Advanced Gigabit Router with PoE and SFP Model: ER-X-SFP
Introduction Thank you for purchasing the Ubiquiti Networks® EdgeRouter™ X SFP. This Quick Start Guide is designed to guide you through installation and also includes warranty terms. Package Contents EdgeRouter X SFP Power Adapter (24V, 2.5A) Power Cord TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above).
Installation Requirements • For indoor applications, use Category 5 (or above) UTP cabling approved for indoor use. • For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the power supply. We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial‑grade, shielded Ethernet cable from Ubiquiti Networks. For more details, visit: www.ubnt.
Top Panel Power PoE Link/Act eth5 Power LED State Status Off Power Off Green Power On Off No Link Green 100/1000 Mbps (1 Gbps) Link Flashing Indicates Activity Off No PoE Green 24V Passive Off No Link Green 10/100/1000 Mbps Link Flashing Indicates Activity Status Link/Act eth0-eth4 PoE Link/Act
Back Panel Power Reset Ground Button Description There are two methods to reset the EdgeRouter to factory defaults: Reset Detail Ground Power • Runtime reset (recommended) The EdgeRouter should be running after bootup is complete. Press and hold the Reset button for about 10 seconds until the eth4 Link LED starts flashing and then becomes solidly lit. After a few seconds, the LED will turn off, and the EdgeRouter will automatically reboot. • Power-on reset Disconnect power from the EdgeRouter.
Hardware Installation Place the EdgeRouter on a flat, horizontal surface or mount it on a wall (mounting screws not included). WARNING: FAILURE TO PROVIDE PROPER VENTILATION MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF CLEARANCE NEXT TO THE VENTILATION HOLES FOR ADEQUATE AIRFLOW. Connecting Power 1. Connect the Power Adapter to the Power port. 2. Connect the Power Cord to the Power Adapter. Connect the other end of the Power Cord to a power outlet.
Connecting Ethernet 1. Connect an Ethernet cable from your computer or host system to the port labeled eth0 on the EdgeRouter. Note: PoE is disabled by default. 2. Connect Ethernet cables from the Ethernet ports of your devices to the rest of the ports in this range: eth1-eth4.
Using the SFP Port (Optional) To use the eth5/SFP port: 1. Remove the protective plug covering the eth5/SFP port. 2. Plug a fiber SFP module into the eth5/SFP port. SN: 9 DDM 15 m 2617 K M310nC 20KM - 20 /Rx1 s SM/S 0M 50nm 00 Mbp 1 Tx15 F1000 E 1308 05 3. Connect a fiber optic cable to the fiber SFP module. Then connect the other end of the cable to another fiber device. For information about compatible fiber SFP modules, visit: ubnt.
Accessing the EdgeOS Configuration Interface The EdgeOS® configuration interface can be accessed via DHCP or static IP address assignment. By default, eth1 is set up as a DHCP client, while eth0 is assigned a static IP address of 192.168.1.1. To configure the EdgeRouter, proceed to the appropriate section: DHCP or “Static IP Address”. DHCP 1. Connect an Ethernet cable from eth1 on the EdgeRouter to a LAN segment that has an existing DHCP server. 2.
4. The login screen will appear. Enter ubnt in the Username and Password fields. Read the Ubiquiti License Agreement, and check the box next to I agree to the terms of this License Agreement to accept it. Click Login. The EdgeOS Configuration Interface will appear, allowing you to customize your settings as needed. For more information, refer to the EdgeOS User Guide, which is available at www.ubnt.com/download/edgemax For more information on PoE configuration, refer to “Configuring PoE Settings”.
Static IP Address 1. Connect an Ethernet cable from the Ethernet port on your computer to the port labeled eth0 on the EdgeRouter. 2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet. 3. Launch your web browser. Type https://192.168.1.1 in the address field, and press enter (PC) or return (Mac). 4. The login screen will appear. Enter ubnt in the Username and Password fields.
Configuring PoE Settings The PoE setting for ports eth0-eth4 is set to Off by default. WARNING: Before activating 24V passive PoE, ensure that the connected device supports PoE and the supplied voltage. 1. On the Dashboard screen, go to Actions > PoE for the interface you want to configure. 2. Select 24V from the PoE drop‑down menu. 3. Click Save. For more information, refer to the EdgeOS User Guide, which is available at www.ubnt.
Specifications EdgeRouter X SFP Dimensions Weight Max. Power Consumption Max. Total PoE Output 142 x 75 x 23 mm (5.59 x 2.95 x 0.91") 215 g (7.58 oz) 5W 50W @ 24V PoE Output Passive 24V (Pins 4, 5+; 7, 8-) Power Input 24VDC, 2.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Failure to provide proper ventilation may cause fire hazard. Keep at least 20 mm of clearance next to the ventilation holes for adequate airflow. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. WARNING: Do not use this product in a location that can be submerged by water.
Limited Warranty www.ubnt.com/support/warranty/ The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions. Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity български [Bulgarian] С настоящото UBIQUITI NETWORKS декларира, че това устройство ER-X-SFP е в съответствие със съществените изисквания и други приложими разпоредби на Директиви 2014/30/ЕС, 2014/35/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: www.ubnt.
Italiano [Italian] Con la presente, UBIQUITI NETWORKS, dichiara che questo dispositivo ER-X-SFP, è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti delle direttive 2014/30/UE, 2014/35/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: www.ubnt.
www.ubnt.com Ubiquiti Networks, Inc. 685 Third Avenue, 27th Floor New York, NY 10017 USA ©2015-2018 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, EdgeMAX, EdgeOS, EdgeRouter, TOUGHCable, and UNMS are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. All other trademarks are the property of their respective owners.
