6-Port Gigabit PoE Router with 1 SFP Port Model: ER-6P
Introduction Thank you for purchasing the Ubiquiti Networks® EdgeRouter™. This Quick Start Guide is designed to guide you through installation and also includes warranty terms. Package Contents EdgeRouter ER-6P Wall Mount Screws (Qty. 2) Power Cord Wall Mount Anchors (Qty. 2) Power Adapter (24V, 2.5A) Ground Screw Cable Clip TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above).
Installation Requirements • Drill with a 6 mm drill bit (for wall-mounting) • Phillips screwdriver • For indoor applications, use Category 5 (or above) UTP cabling approved for indoor use. • For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the power supply.
Hardware Overview Front Panel Ports Console RJ45 (eth0-eth4) SFP (eth5) USB Interface Console Description RJ45 serial console port for Command Line Interface (CLI) management. Use an RJ45‑to-DB9, serial console cable, also known as a rollover cable, to connect the Console port to your computer. (If your computer does not have a DB9 port, then you will also need a DB9 adapter.
Front Panel Button Reset Button Description There are two methods to reset the EdgeRouter to factory defaults: Reset • Runtime reset (recommended) The EdgeRouter should be running after bootup is complete. Press and hold the Reset button for about 10 seconds until the LED for port eth5 starts flashing and then becomes solidly lit. After a few seconds, the LED will turn off, and the EdgeRouter will automatically reboot. • Power-on reset Disconnect the Power Cord from the Power Adapter.
Front Panel LEDs System System LED Note: The System LED functionality has been updated with firmware v1.10.7. We recommend that you update the EdgeRouter to the latest firmware. State Status Flashing White Bootup in progress. White Ready for use, not connected to Ubiquiti® Network Management System (UNMS™). Blue Ready for use, connected to UNMS. Steady Blue with Occasional Flashing Ready for use, unable to connect to UNMS, check connection to UNMS server.
RJ45: PoE SFP: Speed/Link/Act RJ45: Speed/Link/Act RJ45 LEDs LED PoE Speed/ Link/ Activity State Status Off No PoE Green 24V 2-Pair Passive PoE Output Blue 24V 4-Pair Passive PoE Output Off No Link Amber Link Established at 10/100 Mbps Amber Flashing Link Activity at 10/100 Mbps Green Link Established at 1000 Mbps (1 Gbps) Green Flashing Link Activity at 1000 Mbps (1 Gbps) State Status Off No Link Green Link Established at 1 Gbps Green Flashing Link Activity at 1 Gbps SFP LED
Back Panel Ventilation Holes Power Grounding Point Note: There are additional ventilation holes on the sides of the EdgeRouter. Hardware Installation WARNING: FAILURE TO PROVIDE PROPER VENTILATION MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF CLEARANCE NEXT TO THE VENTILATION HOLES FOR ADEQUATE AIRFLOW. Wall Mounting To mount the EdgeRouter on a wall, you will need a drill, a 6 mm drill bit, and a Phillips screwdriver. 1. Use a 6 mm drill bit to drill two holes 125 mm apart. 2.
3. Position the EdgeRouter with the Ethernet ports facing down. Place the wall-mount slots of the EdgeRouter over the screw heads on the wall. Then slide the EdgeRouter down to lock it into place. Grounding the EdgeRouter (Recommended) The EdgeRouter is grounded through the Power Adapter; however, you can add optional ESD grounding for enhanced ESD protection. 1. Attach the Ground Screw to secure a ground wire (not included) to the Grounding Point. 2.
Connecting Power 1. Connect the Power Adapter to the Power port. 2. Connect the Power Cord to the Power Adapter. 3. Connect the other end of the Power Cord to a power outlet.
Using SFP Ports To use an SFP port: 100 Tx1 0M 550 bp nm s SM /Rx /SC 131 0nm20K M DD M 1. Remove the protective plug covering the SFP port. 2. Plug a fiber SFP module into the SFP port. 3. Connect a fiber optic cable to the fiber SFP module. Then connect the other end of the cable to another fiber device. For information about compatible fiber SFP modules, visit: ubnt.
Accessing the EdgeOS Configuration Interface The EdgeOS® configuration interface can be accessed via DHCP or static IP address assignment. By default, eth1 is set up as a DHCP client, while eth0 is assigned a static IP address of 192.168.1.1. To configure the EdgeRouter, proceed to the appropriate section: DHCP or “Static IP Address”. DHCP 1. Connect an Ethernet cable from eth1 on the EdgeRouter to a LAN segment that has an existing DHCP server. 2.
4. The login screen will appear. Enter ubnt in the Username and Password fields. Read the Ubiquiti License Agreement, and check the box next to I agree to the terms of this License Agreement to accept it. Click Login. The EdgeOS Configuration Interface will appear, allowing you to customize your settings as needed. For more information, refer to the EdgeOS User Guide, which is available at www.ubnt.com/download/edgemax For more information on PoE configuration, refer to “Configuring PoE Settings”.
2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet. 3. Launch your web browser. Type https://192.168.1.1 in the address field. Press enter (PC) or return (Mac). 4. The login screen will appear. Enter ubnt in the Username and Password fields. Read the Ubiquiti License Agreement, and check the box next to I agree to the terms of this License Agreement to accept it. Click Login.
Configuring PoE Settings The PoE setting for ports eth0-eth4 is set to Off by default. WARNING: Before activating PoE, ensure that the connected device supports passive PoE and the supplied voltage. 1. In the Dashboard tab, click Actions > PoE of the Ethernet port you want to configure. 2. The Interface Configuration window will appear. Select the appropriate PoE setting, and click Save.
3. The Ethernet port’s PoE LED will confirm the PoE setting. PoE (eth0-eth4) For detailed instructions on configuring other features, please refer to the EdgeOS User Guide. The User Guide is available at www.ubnt.com/download/edgemax You can also manage your device using the Ubiquiti Network Management System. UNMS lets you configure, monitor, upgrade, and back up your devices using a single application. Get started at www.unms.
Specifications ER-6P Dimensions 229 x 136.5 x 31.1 mm (9.02 x 5.37 x 1.22") Weight 730 g (1.61 lb) Max. Power Consumption Power Method 16W (Excludes PoE Output) External AC/DC Power Adapter, 60W (24V, 2.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Failure to provide proper ventilation may cause fire hazard. Keep at least 20 mm of clearance next to the ventilation holes for adequate airflow. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. WARNING: Do not use this product in location that can be submerged by water.
Limited Warranty www.ubnt.com/support/warranty/ The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions. Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. 1.
CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity български [Bulgarian] С настоящото UBIQUITI NETWORKS декларира, че това устройство ER-6P е в съответствие със съществените изисквания и други приложими разпоредби на Директиви 2014/30/ЕС, 2014/35/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: www.ubnt.
Italiano [Italian] Con la presente, UBIQUITI NETWORKS, dichiara che questo dispositivo ER-6P, è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti delle direttive 2014/30/UE, 2014/35/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: www.ubnt.com/compliance Latviešu valoda [Latvian] Ar šo, UBIQUITI NETWORKS, deklarē, ka ER-6P ierīce, ir saskaņā ar būtiskajām prasībām un citiem attiecīgiem noteikumiem Direktīvās 2014/30/ES, 2014/35/ES.
www.ubnt.com Ubiquiti Networks, Inc. 685 Third Avenue, 27th Floor New York, NY 10017 USA ©2017-2019 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, EdgeMAX, EdgeOS, EdgeRouter, TOUGHCable, and UNMS are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. All other trademarks are the property of their respective owners.
