User's Guide

【Introduction】
【App INSTALLATION】
1. Appearance Introduction
2. Screen Icons Introduction
3. Device Operations
1. App INSTALLATION
2. PC Offline Tools Installation
3. WiFi Setup
4. ETH network Setup
( suits AETH1RS version)
This manual book is a general guidance for all types of our Industrial-grade GS1
devices. Some features which are marked with asterisk are available for specific
versions. Please refer to related instructions according to the version you purchased.
Industrial-grade Wireless
Smart Multi-Sensor Device GS1
User Guide
Menu button
Light sensor*
External power plugged in
DC5V-12V Power port
Temperature & humidity sensor
WiFi/GPRS antenna*
Power button
USB Type-C
Ethernet cable port*
RS485 interface*
SIM
T/H
E-T/H
S-T/H
E-T
LIGHT
WS
CO
2
PH
AP
×
×
SIM
m/s
CO
2
PH
RH%
T/H
Lux
X100
PPM
X100
Usage
S-T/H
E-T/HE -TLIGHTWSCO
2
PH
AP
PH sensor*
Storage status
CO2 sensor*
Wind speed sensor*
Light sensor *
External temperature sensor *
Soil temperature and humidity sensor*
External temperature and humidity sensor*
Internal temperature and humidity sensor
Ethernet cable connected*
Error code
Device setup mode
SIM card installed*
Mobile data strength*
Sending data
Network connection/ failure
Press and hold the power button for 3 seconds until the screen
is lit up. Release the button and the device is now on.
Press the menu button once to toggle between the internal
sensor readings and external probe readings.
Download the App from www.ubibot.io/setup
Or
Search for “UbiBot” on the App Store or Google
Play.
Launch the App, register an account if needed and log
in. On the home screen click the “+” to add your
device. Scan the QR code on the back of the device, or
manually enter the serial number.
Download the tool from www.ubibot.io/setup
Please note that this tool is for professional use only to export
offline data to PC.
Press the menu button twice in quick succession to enable or
disable the voice guide. This will also refresh the last sensing
data.
Press the power button twice to toggle between displaying
Celsius or Fahrenheit. This will also refresh the last sensing data.
Pressing either of the buttons will switch on the display
backlight for a short time. Pressing both the two buttons at the
same time will keep the backlight alight constantly. Pressing
another time will switch off the backlight.
Switch the device off. Now press and hold the menu button and
power buttons together for at least 8 seconds. Release the
buttons when you hear the voice guidance “ The device will now
reset”.
Press and hold the power button for 3 seconds until the screen
is off. The device is now off.
With the device switched on, press and hold the menu button
for 3 seconds. Release the button until the AP icon flashes on
the screen.
With the device switched on, press the power button once to
trigger a manual data sync. The icon will flash while the data
is being transferred. You can also hear the voice guidance.
WiFi connection/ failure
Battery level
Switch On
Switch Off
Device Setup Mode
Manual Data Synchronisation
Toggle Screen Readings
Toggle Celsius or Fahrenheit*
Display Backlight *
Reset to Default Settings
Switch On/Off Voice Guide*
1 2 3 4 5 6
STEP1.
Put your device into device setup mode . The AP icon
should flash on the screen.
STEP2.
Plug in the Ethernet cable into the port on the left side
of the device.
STEP1.
Launch the app, register if needed and log in. On the
main screen, click the “+” to add your device. Scan the
QR code on the back of the device, or manually enter
the serial number. Follow the onscreen guidance to
complete the setup.
STEP2.
The device will ask you to enter your WiFi password.
Check that the correct SSID is selected and enter the
password.The App will now prompt you to go to your
phone settings screen. Change to the UbiBot-xxx
network and return to the App.
The device will now complete the setup process,
register with the server and do the initial data sync.
Your phone will automatically switch back to its
normal WiFi network. If the connection failed, please
repeat the process and ensure you entered the correct
WiFi details in step 3.
STEP3.
STEP4.
IMPORTANT
ALL STORED DATA WILL BE LOST IF YOU RESET YOUR DEVICE TO DEFAULT
SETTINGS!
REMEMBER TO SYNCHRONISE THE SENSING DATA TO THE UBIBOT® IoT
PLATFORM OR EXPORT THE DATA TO YOUR COMPUTER BEFORE RESETTING IT.
Device Management
Αδ δ ψουρ δ ε ϖιχε Σχαν τηε ΘΡ χοδ ε
ＷＬ Ａ Ｎ
Ｕｂｉｂｏｔ－ ５０８４６
ＷＬ ＡＮ
Next Step
Serial No.
SSID
Password