Programming instructions

Intermec Fingerprint v7.61 – Programmer’s Reference Manual Ed. 7328
Chapter 8 EasyLAN 100i Setup
lan1 section
Objects
NODE_ADDR, HP_JETADMIN, DEF_OUT, SYS_LOC, SYS_CONT, NETW_ENB,
PS_NAME, JOB_CHECK_DELAY, CONF_CHECK_DELAY, FR_802_3,
FR_ETH_2, FR_802_2, FR_SNAP, NCP_BURST_MODE, PSERVER_NDS,
PSERVER_BINDERY1, PSERVER_BINDERY2, PSERVER_BINDERY3,
PSERVER_BINDERY4, PSERVER_BINDERY5, PSERVER_BINDERY5,
PSERVER_BINDERY7, PSERVER_BINDERY8, PSERVER_BINDERY9,
PSERVER_BINDERY10, PSERVER_BINDERY11, PSERVER_BINDERY12,
PSERVER_BINDERY13, PSERVER_BINDERY14, PSERVER_BINDERY15,
PSERVER_BINDERY16, NPRINTER1, NPRINTER2, NPRINTER3,
NPRINTER4, NPRINTER5, NPRINTER6, NPRINTER7, NPRINTER8,
LSLM_ENB, NB_FR_TYPE, LPRINT_1, LLOGIC_1, LPRINT_2, LLOGIC_2,
LPRINT_3, LLOGIC_3, LPRINT_4, LLOGIC_4, LPRINT_5, LLOGIC_5,
LPRINT_6, LLOGIC_6, LPRINT_7, LLOGIC_7, LPRINT_8, LLOGIC_8,
PR1_IN, PR1_BEF, PR1STR, PR1_AFT, PR1_IN, PR1_BEF, PR1STR,
PR1_AFT, PR1_IN, PR1_BEF, PR1STR, PR1_AFT, PR2_IN, PR2_BEF,
PR2STR, PR2_AFT, PR3_IN, PR3_BEF, PR3STR, PR3_AFT, PR4_IN,
PR4_BEF, PR4STR, PR4_AFT, PR5_IN, PR5_BEF, PR5STR, PR5_AFT,
PR6_IN, PR6_BEF, PR6STR, PR6_AFT, PR7_IN, PR7_BEF, PR7STR,
PR7_AFT, PR8_IN, PR8_BEF, PR8STR, PR8_AFT, TCP_ENB, INT_ADDR,
DEF_ROUT, NET_MASK, PROSPRT, LPD_BANN, DHCP_ENB, BOOTP_ENB,
RARP_ENB, WINS_ENB, WINS_ADDR1, WINS_ADDR2, NBT_SCOPE_ID,
RTN_OPT, RTEL_PR1, RTEL_PR2, RTEL_PR3, RTEL_PR4, RTEL_PR5,
RTEL_PR6, RTEL_PR7, RTEL_PR8, READ_COM, WRT_COM, TRAPADDR,
TRAP_COM, SYS_NAME, SNMP_AUT,TRAP_PRT
Value Syntax
As defi ned by Axis.
Example
SETUP "lan1","RTEL_PR1","9090"
Limitations
NODE_ADDR is read-only.
Section "lan1" is impervious to volatile setup mode, that is, the setting
will be stored non-volatile
.
If the ip-settings are changed, the printer must be rebooted to update
to the new settings.
Sections, Objects,
and Values, cont.