Programming instructions

Intermec Fingerprint v7.61 – Programmer's Reference Manual Ed. 7326
Chapter 7 Error Messages
1025 File does not exist.
1026 Label pending.
1027 Out of transfer ribbon.
1028 Paper type is not selected.
1029 Printhead voltage too high.
1030 Character is missing in chosen font.
1031 Next label not found.
1032 File name too long.
1033 Too many fi les are open.
1034 Not a directory.
1035 File pointer is not inside the fi le.
1036 Subscript out of range.
1037 No acknowledge received within specifi ed timeout.
1038 Communication checksum error.
1039 Not mounted.
1040 Unknown fi le operating system.
1041 Error in fos structure.
1042 Internal error in mcs.
1043 Timer table full.
1044 Low battery in memory card.
1045 Media was removed.
1046 Memory checksum error.
1047 Interrupted system call.
1051 Dot resistance measure out of limits.
1052 Error in printhead.
1053 Unable to complete a dot measurement.
1054 Error when trying to write to device.
1055 Error when trying to read from device.
1056 O_BIT open error.
1057 File exists.
1058 Transfer ribbon fi tted.
1059 Cutter does not respond.
1060 DC motor to ribbon save did not start/stop.
1061 Wrong type of media.
1062 Not Allowed.
1081 Timer expired
1082 Unsupported protocol
1083 Ribbon Low
1101 Illegal character in bar code.
1102 Illegal bar code font.
1103 Too many characters in bar code.
1104 Bar code too large.
1105 Bar code parameter error.
1106 Wrong number of characters.
1107 Illegal bar code size.
1108 Number or rows out of range.
1109 Number of columns out of range.
1201 Insuffi cient font data loaded.
1202 Transformation matrix out of range.
1203 Font format error.
1204 Specifi cations not compatible with output module.
1205 Intelligent transform not supported.
1206 Unsupported output mode requested.
1207 Extended font not supported.
1208 Font specifi cations not set.
1209 Track kerning data not available.
1210 Pair kerning data not available.
1211 Other Speedo error.
1212 No bitmap or outline device.
1213 Speedo error six.
1214 Squeeze or clip not supported.
1215 Character data not available.
1216 Unknown font.
1217 Font format is not supported.
1218 Correct mapping table is not found.
1219 Font is in the wrong direction.
1220 Error in external map table.
1221 Map table was not found.
1222 Double byte map table is missing.
1223 Single byte map table is missing.
1224 Character map function is missing.
1225 Double byte font is not selected.
1301 Index outside collection bounds.
1302 Collection could not be expanded.
1303 Parameter is not a collection.
1304 Item not a member of the collection.
1305 No compare function, or compare returns faulty value.
1306 Tried to insert a duplicate item.
1601 Reference Font Not Found.
1602 Error in Wand-Device.
1603 Error in Slave Processor.
1604 Print Shift Error.
1605 No Hardware Lock.
1606 Testfeed not done.
1607 General Print Error.
1608 Access Denied.
1609 Specifi ed Feed Length Exceeded.
1610 Illegal Character Map File.
1701 Cutter Error1 (EasyCoder F-series only
1
)
1702 Cutter Error2 (EasyCoder F-series only
1
)
1703 Cutter Error3 (EasyCoder F-series only
1
)
1704 Cutter open (EasyCoder F-series only
1
)
Code Message/Explanation Code Message/Explanation
1
/. See EasyCoder F2 & F4 Service Manual.