Programming instructions

Intermec Fingerprint v7.61 – Programmer’s Reference Manual Ed. 7236
Chapter 2 Program Instructions
SETUP, cont.
Remarks, cont. When creating setup fi les or setup strings, there is a special syntax for each
parameter that must be followed exactly. Variable numeric input data are
indicated by “n” – “nnnnn”, alternative data are indicated by bold characters
separated by vertical bars (|). Compulsory space characters are indicated by
double-headed arrows (
↔
). Note that some parameters listed below may only
apply to a certain printer model or an optional device.
Important!
Do not include any double-headed arrows (
↔
) or vertical bars (|) when
typing a setup string or fi le!
"SER-COM,UART1|UART2|UART3,BAUDRATE,300|600|1200|2400|4800|9600|19200|38400|57600|115200"
"SER-COM,UART1|UART2|UART3,CHAR
↔
LENGTH,7|8"
"SER-COM,UART1|UART2|UART3,PARITY,NONE|EVEN|ODD|MARK|SPACE"
"SER-COM,UART1|UART2|UART3,STOPBITS,1|2"
"SER-COM,UART1|UART2|UART3,FLOWCONTROL,RTS/CTS,ENABLE|DISABLE"
"SER-COM,UART1|UART2|UART3,FLOWCONTROL,ENQ/ACK,ENABLE|DISABLE"
"SER-COM,UART1|UART2|UART3,FLOWCONTROL,XON/XOFF,DATA
↔
FROM
↔
HOST,ENABLE|DISABLE"
"SER-COM,UART1|UART2|UART3,FLOWCONTROL,XON/XOFF,DATA
↔
TO
↔
HOST,ENABLE|DISABLE"
"SER-COM,UART2,PROT
↔
ADDR,ENABLE|DISABLE"
"SER-COM,UART1|UART2|UART3,NEW
↔
LINE,CR/LF|LF|CR"
"SER-COM,UART1|UART2|UART3,REC
↔
BUF,nnnnn"
"SER-COM,UART1|UART2|UART3,TRANS
↔
BUF,nnnnn"
"SER-COM,UART2,PROTOCOL
↔
ADDR.,nn"
"NET-COM,NET1,NEW
↔
LINE,CR/LF|LF|CR"
"FEEDADJ,STARTADJ,nnnn" (negative value allowed)
"FEEDADJ,STOPADJ,nnnn" (negative value allowed)
"MEDIA,MEDIA
↔
SIZE,XSTART,nnnn"
"MEDIA,MEDIA
↔
SIZE,WIDTH,nnnn"
"MEDIA,MEDIA
↔
SIZE,LENGTH,nnnnn"
"MEDIA,MEDIA
↔
TYPE,LABEL
↔
(w
↔
GAPS)|TICKET
↔
(w
↔
MARK)|TICKET
↔
(w
↔
GAPS)|FIX
↔
LENGTH
↔
STRIP|VAR
↔
LENGTH
↔
STRIP"
"MEDIA,PAPER
↔
TYPE,TRANSFER|DIRECT
↔
THERMAL"
"MEDIA,PAPER
↔
TYPE,DIRECT
↔
THERMAL,LABEL
↔
CONSTANT,nnn"
"MEDIA,PAPER
↔
TYPE,DIRECT
↔
THERMAL,LABEL
↔
FACTOR,nnn"
"MEDIA,PAPER
↔
TYPE,TRANSFER,RIBBON
↔
CONSTANT,nnn"
"MEDIA,PAPER
↔
TYPE,TRANSFER,RIBBON
↔
FACTOR,nnn"
"MEDIA,PAPER
↔
TYPE,TRANSFER,LABEL
↔
OFFSET,nnn"
"MEDIA,PAPER
↔
TYPE,TRANSFER,LOW
↔
DIAMETER,nnn"
"MEDIA,CONTRAST,-10%|-8%|-6%|-4%|-2%|0%|2%|4%|6%|8%|10%"
"PRINT
↔
DEFS,PRINT
↔
SPEED,nnn"
"PRINT
↔
DEFS,LTS
↔
VALUE,nn"
"NETWORK,IP
↔
SELECTION,MANUAL|DHCP|BOOTP|RARP"
"NETWORK,IP
↔
ADDRESS,nnn.nnn.nnn.nnn"
"NETWORK,NETMASK,nnn.nnn.n.n"
"NETWORK,DEFAULT
↔
ROUTER,nnn.nnn.nnn.nnn "