DVW3201B Advanced Wireless Voice Gateway Firmware Version: 9.8.3012_D1 Subscriber User Guide May 2012 www.ubeeinteractive.com 8085 S. Chester Street, Suite 200 Englewood, CO 80112 1.888.390.8233 Sales (email): amsales@ubeeinteractive.com Support (email) amsupport@ubeeinteractive.
Notices and Copyrights Copyright 2012 Ubee Interactive. All rights reserved. This document contains proprietary information of Ubee and is not to be disclosed or used except in accordance with applicable agreements. This material is protected by the copyright laws of the United States and other countries.
Contents 1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 Understanding Safety and Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.1 Understanding Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1.2 Understanding Eco-Environmental Statements . . . . . . . . . . . . . . . . . . . . . . . 1.1.
Ubee Interactive 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11 5.12 5.13 Using the Gateway Information Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Setup Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.1 Viewing IPv6 Addresses in the Gateway Setup Option . . . . . . . . . . . . . . . . 5.2.2 Using the LAN IPv6 Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 Introduction Welcome to the Ubee family of data networking products. This guide is specific to the DVW3201B and serves the following purposes: Provides multiple system operators (MSOs) for cable systems with all information necessary to operationally stage, deploy, and support the DVW3201B. Provides the technical details needed to locally and remotely manage deployed devices.
Understanding Safety and Regulatory Information 1.1 Ubee Interactive Understanding Safety and Regulatory Information The following information provides safety and regulatory standards to install, maintain, and use the DVW3201B Advanced Wireless Voice Gateway. 1.1.1 Understanding Safety WARNING: The following information provides safety guidelines for anyone installing and maintaining the DVW3201B.
Ubee Interactive 1.1.3 Understanding Connections and Applications Understanding Regulatory Statements The following regulatory statements apply to the DVW3201B. Industry North America Statement: This device complies with RSS-210 of the Industry North America Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
Checking Device Package Components 1.4 Ubee Interactive Checking Device Package Components The package for the DVW3201B contains the following items: Item Description 1 - RJ45 Cable (Ethernet) Length ~ 6.0 ft RoHS & UL compliant Sample image, actual appearance subject to change. 1 - RJ11 Cable (Telephone) Sample image, actual appearance subject to change. 1 - AC Power Cord 10A / 125V Sample image, actual appearance subject to change. 1 - Lithium-ion Battery Model: SMPCM9 Rating: 11.1V @ 2.55 Ah 28.
Ubee Interactive 1.5 Understanding the Device Rear Panel Understanding the Device Rear Panel Review the following image and descriptions of the rear panel connections on the device. Item Description RESET Restores the default settings of the device including wireless and custom gateway settings. Use a pointed object to push down the reset button for 5-10 seconds until the power LED turns off. After the power LED turns off, release the button.
Understanding Specifications, Standards, and Firmware Ubee Interactive Item Description WPS 1.6 Connects a PIN-protected Wi-Fi device to the cable modem when the Wi-Fi Protected Setup method is used. When the WPS button is pushed or triggered through the device’s Web UI, an LED on the top-front of the device flashes for four minutes until a PIN is entered from the wireless client, such as a laptop computer, that wants to connect.
Ubee Interactive Understanding Specifications, Standards, and Firmware Max Bandwidth of 4 Channels = 122.88 (108) Mbps, bandwidth per channel (up to 4 channels) = [QPSK 0.32 ~ 10.24 Mbps, 8 QAM 0.48 ~ 15.36 Mbps, 16 QAM 0.64 ~ 20.48 Mbps, 32 QAM 0.80 ~ 25.60 Mbps, 64 QAM 0.96 ~ 30.72 Mbps, 128 QAM/TCM 30.72 Mbps] Symbol Rate: 160, 320, 640, 1280, 2560, 5120 Ksps RF Output Power: TDMA/ATDMA: +8dBmV to +54dBmV (32/64 QAM). ATDMA Only: +8dBmV to +55dBmV (8/16 QAM), +8dBmV to +58dBmV (QPSK).
Understanding Default Values and Logins 1.7 Ubee Interactive Understanding Default Values and Logins The DVW3201B is pre-configured with the following parameters. Some regions may change default values using the cable modem or XML configuration file. Check with your provisioning team to determine the default values for your region. Local Port Address: 192.168.100.1, Web Interface: http://192.168.100.1 Operation Mode: NAT Mode Subnet Mask: 255.255.255.
Ubee Interactive 1.8.1 Understanding LED Operations Understanding the Device Front Panel The following image represents the front panel of the device. LED descriptions are provided in the following table. 1.8.2 Understanding LED Behavior The following table summarizes the behavior of the device LEDs. LED Color Description POWER White On – Internal power-on completes successfully. Blinks – Power-on fails. DS/US White Blinks – Initializing.
Understanding LED Operations LED Ubee Interactive Color Description BATTERY White On – The battery is installed and AC power is on and properly functioning. Off – If there is no AC power to the device, the Battery LED is Off, the Power LED flashes, and the TEL1 LED is On. All other LEDs are Off. Blinks – If the battery is at low power level (30mins left).
2 Installing the DVW3201B This chapter explains how to set up and connect the DVW3201B, connect additional devices, and troubleshoot the installation. Topics See the following topics: Setting Up and Connecting the DVW3201B on page 11 Connecting Devices to the Network on page 12 Troubleshooting the Installation on page 14 2.1 Setting Up and Connecting the DVW3201B Use the following instructions to set up and connect the DVW3201B.
Connecting Devices to the Network Ubee Interactive 3. Power on your PC. The PC must have an Ethernet network adaptor or Ethernet port and an Internet browser installed, such as Netscape or Internet Explorer. The following browsers are supported: For Windows 2000, XP, Vista, Windows 7, Firefox 1.07 and higher, Internet Explorer v7 and above, Netscape. For MAC OS X, 10.2, and higher: Firefox 1.07 and higher, Safari 1.x and higher. 4.
Ubee Interactive Connecting Devices to the Network 4. If the connected device is a gaming console, perform any online task supported by the console (for example, log into the gaming server, play an online game, download content). Refer to Troubleshooting the Installation on page 14 for troubleshooting information. 2.2.2 Connecting a Wireless Device Use the following steps to connect a wireless device to the cable modem (for example, a laptop computer). Default values are shown in the steps below.
Troubleshooting the Installation Ubee Interactive 4. Confirm connectivity by opening a Web browser and going to any Web site (for example, http://www.wikipedia.org) or access the Web interface for the DVW3201B. Note The Web interface allows you to customize the configurations and capabilities for the device. For a full explanation of all Web interface functions, refer to Using the Web User Interface on page 17.
Ubee Interactive Troubleshooting the Installation 2. Choose the Device Manager tab and look for a yellow exclamation point or red X over the network interface card (NIC) in the Network Adaptors field. If you see either one, you may have an interrupt request (IRQ) conflict. Refer to the manufacturer’s documentation or your service provider for further assistance. Verify that TCP/IP is the default protocol for your network interface card.
Troubleshooting the Installation 16 Ubee Interactive Ubee DVW3201B Advanced Wireless Voice Gateway Subscriber User Guide • May 2012
3 Using the Web User Interface The Web user interface (UI) for the DVW3201B is easy to use and allows you to view and configure several settings for your wireless gateway device. You can also validate the installation by accessing the Web user interface on the device. Topics See the following topics: Accessing the Web Interface on page 17 Logging Out of the Web Interface on page 18 Understanding Operation Modes and the Web User Interface on page 19 3.
Logging Out of the Web Interface Ubee Interactive Note:The MAC address of the device can be found on the device label, usually on the bottom of the cable modem. Standard subscriber Web interface login (enter in lower case letters): Username: user Password: user 5. Click OK. The Cable Modem screen of the Web interface is displayed. Subscriber Options: 3.2 Logging Out of the Web Interface Log out when finished using the Web user interface. Steps To log out of the user interface: 1.
Ubee Interactive Understanding Operation Modes and the Web User Interface The logout screen is displayed. 2. Click Back to Login to access the Login screen and begin a new user interface session. 3.3 Understanding Operation Modes and the Web User Interface The DVW3201B provides four operation modes. Different options are available in the Web user interface depending on the mode and the type of user logged in. The operation mode is set from the Tools menu Operation Mode option.
Understanding Operation Modes and the Web User Interface Ubee Interactive Router Operates in Router Mode for assigning Static Public IP addresses with RIP when this mode is enabled. DHCP, Firewall, and NAT functionality are disabled by default. When Route Mode is enabled, you can configure the device from the Web User Interface (UI) Routing screen, or through the Telnet Command Line Interface (CLI). Refer to Using the Routing Setup Option on page 92 for more information.
4 Understanding the Modem Menu The Modem menu of the Web interface allows you to access information about the modem, such as status and battery information.
Using the Information Option Ubee Interactive Steps To view modem information: 1. Click the Modem link from the top of the screen. 2. Click the Information link from the left side of the screen. Field explanations are listed below the following screen example. Label Description Cable Modem Information Cable Modem Defines the current DOCSIS standard of the device. MAC Address Defines the unique media access control (MAC) hardware address of the cable modem.
Ubee Interactive 4.2 Using the Status Option Using the Status Option The Status screen displays the device’s general connection information. Steps To view modem status: 1. Click the Modem link from the top of the screen. 2. Click the Status link from the left side of the screen. Field explanations are listed below the following screen example. Label 4.3 Description Acquired Downstream Channel Displays the Downstream channel tat the cable modem is trying to lock to and its progress.
Using the Downstream Option Ubee Interactive Label 24 Description DS-1 to DS-8 Numbers the downstream channels. Frequency Displays the downstream channel frequency on which the cable modem is scanning. Lock Status Displays if the cable modem succeeded in locking to a downstream channel. Channel Id Displays the downstream channel ID. Modulation Displays the modulation method required for the downstream channel to lock on to by the cable modem. This method is determined by the service provider.
Ubee Interactive Using the Upstream Option Label 4.4 Description RxMER (dB) Displays the Receiver Modulation Error Ratio used to quantify the performance of a digital radio receiver in a communications system using digital modulation. Correctable Codewords Displays the quantity of codewords which are correctable. Uncorrectable Codewords Displays the quantity of codewords which are not correctable. Refresh Updates the screen with the latest information.
Using the Operation Config Option Ubee Interactive Label 4.5 Description Modulation Displays the current cable modem upstream modulation type (QPSK/ QAM8 /QAM16/ QAM32/ QAM64/ QAM128/ QAM256). Symbol Rate (Ksym/sec) Displays the symbol rate. Upstream Mini-Slot Size Displays the current cable modem upstream mini-slot size in Timebase Ticks of 6.25. Power Level (dBmV) Displays the current cable modem upstream transmit power in decibel millivolts. T-1 Displays DHCP time expiration.
Ubee Interactive Using the Event Log Option Label Description General Configuration Network Access Displays the status of the cable modem. Denied – Connectivity is not established. Allowed – connectivity is established to the Internet. Maximum Number of CPEs Displays the maximum number of Ethernet devices that can be connected (LAN side) to access the network at the same time. Baseline Privacy Displays highlighted device configurations, such as PHS Enabled.
Using the Battery Info Option Ubee Interactive Label 4.7 Description First Time Displays the time the event started. Last Time Displays the last time the event was last recorded. Priority Displays the event log severity. Description Displays a detailed description of the event log. Refresh Updates the event log record to its most current state when you click Refresh.
Ubee Interactive Using the Battery Info Option Label Description Current Power Source Displays the power source for the device, such as Utility through the power cord or internal battery power. State Displays the status of the battery, such as Sleep or Idle. Temperature Displays the battery temperature in Fahrenheit and Celsius. Estimated Time Remaining Displays how much time is left on the battery in minutes. Low Battery Time Displays low battery time in minutes.
Using the Battery Info Option 30 Ubee Interactive Ubee DVW3201B Advanced Wireless Voice Gateway Subscriber User Guide • May 2012
5 Understanding the Gateway Menu The Gateway functions provide the majority of configuration for the device including WAN IP addresses, LAN IP addresses, and DHCP. Advanced settings like MAC filtering and port forwarding are provided.
Using the Gateway Information Option 5.1 Ubee Interactive Using the Gateway Information Option The Information option allows you to view basic information for the device. Steps To view gateway information: 1. Click the Gateway link from the top of the screen. 2. Click Information. Information fields are defined following this screen example.
Ubee Interactive Using the Gateway Information Option Label Description Internet Settings Gateway MAC Address Displays the Media Access Control (MAC) address of the residential gateway. Internet IP Address Displays the Internet IP address obtained from the service provider. Subnet Mask Displays the subnet mask of the Internet IP address. Default Gateway Displays the default gateway IP address. DNS Displays the DNS server IP address.
Using the Setup Option Ubee Interactive Label 5.2 Description Private IP Range Displays the private IP address assigned to the DHCP client. Public IP Range Displays the Public IP DHCP Server Range. System Up-Time Displays the accumulated time since the last power cycle. Using the Setup Option The Setup option allows you to make basic configurations to the device. Steps To configure gateway settings: 1. Click the Gateway link from the top of the screen. 2.
Ubee Interactive Using the Setup Option Label Description MAC Address Displays the WAN interface’s hardware address. Duration Displays the accumulated time since successfully acquiring a WAN public IP address. Expires Displays the remaining time before the WAN IP address expires, if applicable. IPv4 DNS Servers Lists the DNS servers available on the network. Release WAN Lease Releases the WAN public IP address when clicked. Renew WAN Lease Renews the WAN IP address when clicked.
Using the Setup Option 5.2.1 Ubee Interactive Viewing IPv6 Addresses in the Gateway Setup Option Additional IP addresses are needed to support the increase in Internet activity. Internet Protocol version 6 (IPv6) addressing is supported by the DVW3201B and displayed when the CMTS uses IPv6. The screen shot below displays an IPv6 address configuration in the Gateway Basic Setup option. 5.2.2 Using the LAN IPv6 Option When the CMTS supports IPv6 address configuration, the LAN IPv6 option is available.
Ubee Interactive Using the DHCP Option Label 5.3 Description IP Address Displays the IPv6 address of the connected device. MAC Address Displays the MAC address of the connected device. Reachability State Displays the status of the neighboring device. Reachable indicates the device can be contacted and configuration information can be obtained from the device. Using the DHCP Option The dynamic host configuration protocol (DHCP) option allows you to configure DHCPspecific behavior on the device.
Using the DHCP Option Ubee Interactive Label 38 Description DHCP Server Enables (Yes) or disables (No) DHCP on the device. If No is selected, all the static DHCP rules in this screen are ignored. Private Starting Address Defines the starting private IP address for the pool of IP addresses that can be used by connecting clients. Private addresses are translated to public IPs to be used on the network. Public Starting Address Defines the starting public IP address.
Ubee Interactive Using the DHCP Static Lease Option Label 5.4 Description Apply Applies and saves all changes when clicked. DHCP Clients Lists all DHCP clients currently connected to the device, either via an Ethernet link, or via a wireless connection. Each client is listed with the following information: MAC Address / IP Address / Subnet Mask Duration / Expires: Duration displays the accumulated time since the client acquired the IP address.
Using the Time Option Ubee Interactive Label 5.5 Description Index Provides an index number for each client that connects to your network. MAC Address Defines the MAC address of the client to which you want to assign a static IP address. IP Address Defines an IP address to the specific client/host. Enabled Activates this rule when Enable is checked. Clear Deletes the rule when Clear is checked. Apply Saves all screen changes when clicked.
Ubee Interactive Using the Advanced Gateway Setup Options Label 5.6 Description Enable SNTP Enables (Yes) or disables (No) the SNTP feature. Current Time Displays the current system time. System Start Time Displays the accumulated time since the system was started. Time Server 1 Defines the IP address or Domain name of the time server. Use the one provided or enter an alternative choice. Time Server 2 Defines the IP address or Domain name of the time server.
Using the Advanced Gateway Setup Options Label 42 Ubee Interactive Description WAN Blocking Blocks connection requests initialized from Internet users when enabled. WAN Blocking must be disabled to be able to PING the WAN gateway IP. Ipsec PassThrough Forces the router to redirect the IPSec request to the local host when enabled. NAT fails this attempt if Internet users initialize an IPSec VPN request to a host located behind the router.
Ubee Interactive Using the Advanced Gateway Setup Options Label DNS Relay Description Allows the cable modem to act as the “relay” device. Each PC that wants to access a URL does not have to send a DNS request to a DNS server on the Internet. DNS is used to resolve a URL (Web site name) to an IP address.
Using the Advanced Gateway Setup MAC Filtering Option Ubee Interactive Label Description SIP Enables or disables the session initiation protocol application layer gateway (SIP ALG). SIP ALG inspects protocol packets and formats SIP message headers and SDP body to ensure proper signaling. Note: Some hosted VoIP services prefer this function to be performed by their own session border controller (SBC) and require the SIP ALG to be disabled. Some IP-PBXs may require SIP ALG enabled. 5.
Ubee Interactive Using the Advanced Gateway Setup IP Filtering Option Label 5.8 Description Index Assigns an index number to the rule. MAC Address Defines the MAC address to block. Clear Deletes the filtering rule when the Apply button is clicked and the Clear box is checked. View Additional Rules: Displays rules 11-20 when selected from the drop-down list, if they exist. A total of twenty rules are supported. Apply Saves all screen changes when clicked.
Using the Advanced Gateway Setup Port Filtering Option Ubee Interactive which you want to deny Internet access. Click Apply. For more information, refer to Using the DHCP Static Lease Option on page 39. A static lease ensures that the device always gets the same IP address. That way, if filtered, it gets filtered continuously. Otherwise, the IP address would change for the device and the filtering rule would not work.
Ubee Interactive Using the Advanced Gateway Setup Forwarding Option For example, to prevent all Telnet access into and across your LAN, you would enter the Start and End ports to be 23, select Both for Protocol, and click the Enabled selection box. Be careful using port filtering by port range as you may accidentally prevent traffic that should pass through your network (for example, http or email).
Using the Advanced Gateway Setup Forwarding Option Ubee Interactive that cannot be accessed from the Internet directly (for example, a request to a local audio server). Port forwarding tells the cable modem to which computer on the local area network to send the data. Here are some examples: Xbox/PlayStation – Games/applications may require port forwarding. Home Security Systems – Security systems that use the Internet may require port forwarding.
Ubee Interactive 5.10.1 Using the Advanced Gateway Setup Forwarding Option Setting Up Port Forwarding for an Xbox Example: To setup Port Forwarding, use the following procedure. See the following page for screen field definitions. Steps To set up port forwarding for an Xbox: 1. Click the Gateway link from the top of the screen. 2. Click Forwarding from the left side of the screen. The following example shows how to setup a single Xbox running Modern Warfare 2.
Using the Advanced Gateway Setup Forwarding Option Label Ubee Interactive Description Internal Index Displays the Index number of the rule. Local IP Defines the last digits of the IP address of the local LAN device to which the forwarding rule applies,. For example, an Xbox or PC. Start Port Defines the starting port number listened to by the server host located in your LAN. End Port Defines the ending port number listened to by the server host located in your LAN.
Ubee Interactive 5.10.2 Using the Advanced Gateway Setup Port Triggering Option Enabled Enables this rule when checked. View Additional Rules Displays rules 11-20 when selected from the drop-down list, if they exist. A total of twenty rules are supported. Apply Saves all screen changes when clicked. Port Map Shows a list of common applications and their ports. Viewing Port Maps Port maps display a list of common applications and the port to which they are assigned.
Using the Advanced Gateway Setup Port Triggering Option Ubee Interactive With port triggering, we define two kinds of ports: Trigger Port and Target Port. Trigger port is the service request with a specific destination port number sent from a LAN side host. Target Port is the port this specific application requires a LAN host to listen to. Thus, the server returns responses to these ports. For example: 1. John requests a file from the Real Audio server (port 7070).
Ubee Interactive Using the Advanced Gateway Settings Pass Through Option Label Trigger Range Defines the trigger port or a range of ports that trigger the router to record the IP address of the LAN computer that sent the traffic to a server on the WAN. Start Port Defines a port number or the starting port number in a range of port numbers. End Port Defines a port number or the ending port number in a range of port numbers.
Using the Advanced Gateway Settings DMZ Host Option Ubee Interactive Steps To set up a pass through table: 1. Click the Gateway link from the top of the screen. 2. Click Pass Through from the left side of the screen. The Pass Through fields are explained following this screen example. Label 5.13 Description Index Defines the index number of the pass through rule. MAC Address Defines the input host’s MAC address. Clear Deletes this rule when checked and the Apply button is clicked.
Ubee Interactive Using the Advanced Gateway Settings DMZ Host Option 4. Go to Tools>>Client List. Your PC and other devices are listed. Note the MAC address and IP address of the Home Gateway, VoIP Phone, or other device to put in the DMZ. For more information, refer to Using the Client List Option on page 83. 5. Go to Gateway>>Static Lease. Enter the MAC address and IP address of a Home Gateway (or other device you wish to be in the DMZ). 6. Click Apply.
Using the Advanced Gateway Settings DMZ Host Option 56 Ubee Interactive Ubee DVW3201B Advanced Wireless Voice Gateway Subscriber User Guide • May 2012
6 Understanding the Wireless Menu This Wireless menu provides settings to configure a wireless network. Topics See the following topics: Using the Wireless Radio Option on page 57 Using the Primary Network Option on page 61 Using the Access Control Option on page 65 Steps To access the wireless menu: 1. Access the Web interface. Refer to Accessing the Web Interface on page 17. 2. Click the Wireless link from the top of the screen. 6.
Using the Wireless Radio Option Ubee Interactive Label 58 Description Wireless Interfaces Displays the wireless name and MAC address. Wireless Displays the wireless radio’s status, Enabled or Disabled. Country Defines the country where this device is used. Output Power Sets the percent of the Output Power for the radio. 802.11 Band Defines the radio band as 2.4Ghz or 5 Ghz. Note: The distance coverage for 5Ghz is less than 2.4Ghz. 802.11 n-Mode Sets the wireless networking standard.
Ubee Interactive Using the Wireless Radio Option Label 6.1.1 Description Regulatory Mode Defines whether Regulatory Mode is set to off, 802.11d, or 802.11h. Pre-Network Radar Check Defines the number of seconds to check for radar on a channel before establishing a network. Current specs specify 60 seconds. Range 0-99. Zero disables checking. Designed so APs avoid channels that contain radar systems. Used for 802.11h only.
Using the Wireless Radio Option Ubee Interactive 2. Click Refresh to update the results. Label 60 Description Network Name Displays the name of the wireless network (SSID) broadcast by the access point. Security Mode Displays the encryption method used. Mode Displays the mode of the wireless access point: Possible modes are: Master – Communicates with associated wireless cards that are in managed mode. Appears as a normal access point with an SSID and channel.
Ubee Interactive 6.2 Using the Primary Network Option Using the Primary Network Option The Primary Network option allows you to configure a variety of wireless security settings. Steps To configure wireless security options: 1. Click the Wireless link from the top of the screen. 2. Click Primary Network from the left side of the screen. The Primary Network fields are explained following this screen example. Note: Wireless default values are discussed in Understanding Default Values and Logins on page 8.
Using the Primary Network Option Ubee Interactive Label 62 Description Primary Network Enables or disables the primary network. Network Name Allows you to define the unique SSID of the cable modem or accept the default. Refer to Understanding Default Values and Logins on page 8 for more information on the SSID. Closed Network Hides the selected SSID when enabled so it is not visible to wireless clients unless manually set up on the client. If disabled, the SSID is visible.
Ubee Interactive Using the Primary Network Option Label Description RADIUS Port Defines a RADIUS port number when WPA or 802.1x network authentication is selected. RADIUS Key Defines the RADIUS Key when WPA or 802.1x network authentication is selected. Group Key Rotation Interval Allows the device to generate the best possible random group key and update all the key-management capable stations periodically.
Using the Primary Network Option Ubee Interactive Label Description WPS Setup AP UUID Defines the universal unique identifier (UUID) for this access point. PIN Defines the Personal Identification Number for this access point. WPS Add Client 6.2.1 Add a client Activates wireless protected setup (WPS) security on the device. To add a client: 1. Click Add a client. The WPS Add Client screen is displayed. 2. Click PUSH on the WPS Add Client screen.
Ubee Interactive 6.3 Using the Access Control Option Using the Access Control Option The Access Control option allows you to configure which clients can access your wireless network. Steps To configure client access: 1. Click the Wireless link from the top of the screen. 2. Click Access Control from the left side of the screen. The Access Control fields are explained following this screen example.
Using the Access Control Option Ubee Interactive Label 66 Description Wireless Interface Defines the network name for which you are setting access control parameters. MAC Restrict Mode Controls wireless access to your network by MAC address. Disabled turns off MAC restrictions and allows any wireless client to connect to this device. However, if you use other security mechanisms for access to the wireless network, clients must still adhere to those restrictions.
Ubee Interactive Deploying and Troubleshooting the Wireless Network Label 6.4 Description MAC Addresses Defines the MAC addresses. Note: You may cut and paste MAC addresses from the connected clients list at the bottom of the screen. Apply Saves changes when clicked. Connected Clients Lists wireless clients currently connected listed by MAC address. MAC Address – Displays the MAC addresses entered in the MAC Addresses field (see above).
Deploying and Troubleshooting the Wireless Network Ubee Interactive Understanding Received Signal Strength Received signal strength (RSSI) is measured from connected wireless client devices to the wireless cable modem. This value can significantly impact wireless speeds/performance.
Ubee Interactive Deploying and Troubleshooting the Wireless Network Attenuation Considerations at 2.4GHz Material Attenuation Glass Window (not tinted) 2dB to 3dB Double Pane Coated Glass 13dB Bullet Proof Glass 10dB Steel / Fire Exit Door 13dB to 19dB Human Body 3dB Trees (Note 2) .
Deploying and Troubleshooting the Wireless Network Ubee Interactive b. Review the speed and signal strength in the Status window. Selecting a Wireless Channel You may need to change the wireless channel on which the wireless cable modem operates when you are in computing, test, and other environments where several wireless access points may be operating in the 2.4Ghz range.
7 Understanding the Firewall Menu This chapter provides instructions to configure the DVW3201B firewall to control what types of traffic are allowed on your network. The firewall can block certain Web-oriented cookies, java scripts, and pop-up windows. It is highly recommended the Firewall is left enabled at all times to protect against denial of service (DoS) attacks. Refer to Using the Basic Option on page 77 to block Internet access to specific sites.
Using the Content Filter Option Ubee Interactive explained following this screen example. Label Description Content Filter Settings Filter Proxy Acts as an intermediary between a user and the Internet to provide security, administrative control, and caching service. When a proxy server is located on the WAN, it is possible for LAN users to circumvent content filtering by pointing to this proxy server. Filter Cookies Stops Cookies from being stored on a connected computer’s hard drive.
Ubee Interactive Using the Event Log Option Label 7.2 Description Firewall Protection Activates the firewall function. Protection against incoming connection requests on routed subnet Protects all the routed subnets connected to the device. Apply Saves the configuration when clicked. Using the Event Log Option The Event Log option allows you to configure firewall event log reporting via email alerts and report on possible attacks on the system. Steps To configure firewall event reporting: 1.
Using the Remote Log Option 7.3 Ubee Interactive Using the Remote Log Option The Remote Log option allows you to configure events to be sent to a local SysLog server. Steps To configure the firewall remote log: 1. Click the Firewall link from the top of the screen. 2. Click Remote Log from the left side of the screen. The Remote Log fields are explained following this screen example. Label 74 Description Permitted Connections Logs all access attempts that are allowed by the firewall.
8 Understanding the Parental Control Menu Parental Controls allow you to control Internet access for users on the DVW3201B network. Parental Controls provides the following features: Define user/password access. Block specific Web sites and Web sites based on keywords. Define the times users are allowed to access the Internet. View an event log to view Internet activity.
Using the Parental Control User Setup Option Ubee Interactive Steps To configure user accounts: 1. Click the Parental Control link from the top of the screen. 2. Click User Setup from the left side of the screen. The User Setup fields are explained following the screen example. Note: To enable Parental Control, refer to Using the Basic Option on page 77. Label 76 Description Add User Remove User Enable Defines user accounts.
Ubee Interactive Using the Basic Option Label 8.2 Description White List Access Only Selects the White List Access option. If you have created a content rule that defines a black list and white list, select the White List Access Only checkbox to force the wireless modem to execute the policy for the selected user. Time Access Rule Selects a defined time access rule to apply to the selected user. Session Duration Allows you to enter a time in minutes for the user’s session to expire.
Using the Basic Option Ubee Interactive Label Description Enable Parental Control Activates the Parental Control feature when checked. Apply Saves all changes in the screen and activates Parental Control, if enabled. Content Policy Configuration 78 Add New Policy Adds a policy to the Policy List. Enter the policy name and click Add New Policy. Content Policy List Lists existing policies you can choose to use. Remove Policy Deletes a policy from the list.
Ubee Interactive Using the Tod Filter Option Label 8.3 Description Allowed Domain List DIsplays domains you can assign to users to visit only the sites allowed. Add Allowed Domain Adds allowed domains to the list. Enter the name and click Add Allowed Domain. Remove Allowed Domain Removes domain names from the list. Highlight the domain from the list and click Remove Allowed Domain.
Using the Event Log Option Ubee Interactive Label 8.4 Description Days to Block Selects the days to block Internet access. Time to Block: All Day or by 24 hour clock time Defines the time to block. To block all day, check All Day to eliminate all access during the days selected. To a specific time, enter the time range in the fields provided in a 24 hour clock (00:00 - 24:00) format. Apply Saves all changes when clicked.
9 Understanding the Tools Menu This chapter instructs you how to use a variety of tools to evaluate and diagnose the DVW3201B. Topics See the following topics: Using Using Using Using Using the the the the the Ping Option on page 81 Trace Route Option on page 82 Client List Option on page 83 Password Option on page 84 User Defaults Option on page 85 Steps To access the tools menu: 1. Access the Web interface. Refer to Using the Web User Interface on page 17. 2.
Using the Trace Route Option Ubee Interactive screen example. Label Description Ping Test Parameters 9.2 Ping Target Defines the IP address to which you want to send a ping. Ping Size Defines the packet size to send for the ping operation. No. of Pings Defines the number of ping commands to send to the ping target. Ping Interval Defines the interval between ping operations in milliseconds. Start Test/Abort Test/Clear Results Defines what you want to do. To start the test, click Start.
Ubee Interactive Using the Client List Option Label Description Tracert Test Parameters 9.3 Tracert Target Defines the specific IP address or domain (for example, yahoo.com) to which you want to trace a route. MAX Hops Defines the MAX hops. Hops is the number of routers that the trace route traverses. Time out Defines the time out interval (100–10000) in milliseconds. Start Test Abort Test Clear Results Defines what you want to do. To start the test, click Start Test.
Using the Password Option Ubee Interactive 2. Click Client List from the left side of the screen. The Client List fields are explained following this screen example. Note – Devices connected with an IPv6 IP address are shown in the Gateway–Setup– LAN IPv6 screen. Label 9.4 Description Hostname DIsplays the hostname of the DHCP clients connected to the DVW3201B. IP Address DIsplays the IP address of the DHCP clients connected to the DVW3201B.
Ubee Interactive Using the User Defaults Option Label 9.5 Description User Name Allows you to enter a new user name for the user account to this web interface of the DVW3201B. See Understanding Default Values and Logins on page 8 for more information on logins and defaults. Enter the new Password and re-enter the new password to confirm. Click Apply to save the changes. New Password Allows you to enter a new password for the user account.
Using the User Defaults Option 86 Ubee Interactive Label Description Restore Factory Defaults to Firewall and Parental Control Restores settings to factory defaults. Select Yes to restore the device to default settings for the Firewall and Parental Control settings. This operation does not require a reset of the system. Reset The system Resets the system. Select Yes to power cycle the device. Apply Applies the options selected in this screen.
10 Glossary This chapter defines terms used in this guide and in the industry. Broadcast A packet sent to all devices on a network. Cable Modem Termination System (CMTS) Typically located in the cable company’s headend, the CMTS is equipment that provides high-speed data services to subscribers, such as cable Internet and VoIP. Channel Bonding A computer networking configuration where two or more network interfaces are combined on a host computer for redundancy or increased throughput.
Ubee Interactive Downstream A term to describe the direction of data from the network service provider to the customer. Dynamic Host Configuration Protocol (DHCP) A protocol that centrally automates the assignment of IP addresses IP Addressin a network. Using the Internet’s set of protocols (TCP/IP) Transmission Control Protocol/Internet Protocol (TCP/IP), each machine that can connect to the Internet needs a unique IP address.
Ubee Interactive Internet Service Provider (ISP) A company that provides individuals and companies access to the Internet and other related services. Interval Usage Code (IUC) Interval usage codes define different profiles for upstream burst profiles to use for the data. IUCs are sent to the cable modem from the CMTS to tell the device important characteristics to use for the burst, such as modulation type, preamble length, and so on.
Ubee Interactive Routing Information Protocol (RIP) A protocol in which routers periodically exchange information with one another to determine minimum-distance paths between sources and destinations. Router A device that forwards data between networks. An IP router forwards data based on IP source and destination addresses. Subnet A portion of a network that shares a common address component. On TCP/IP networks, subnets are defined as all devices whose IP addresses have the same prefix.
Ubee Interactive Upstream A term to describe the direction of data from the customer to the network service provider. Uniform Resource Locator (URL) A URI that specifies where a known resource is available and how to retrieve it. Wide Area Network (WAN) A long-distance link or computer network that spans a relatively large geographical area that connects remotely located LANs. Typically, a WAN consists of two or more LANs. The Internet is a large WAN.
Ubee Interactive 92 Ubee DVW3201B Advanced Wireless Voice Gateway Subscriber User Guide • May 2012
