QUICK START GUIDE Outdoor Collection 30607 Rev_A
QUICK START GUIDE u-line.com WELCOME TO U-LINE Congratulations on your U-Line purchase. Your product comes from a company with over five decades of premium modular ice making, refrigeration, and wine preservation experience. U-Line continues to be the American leader, delivering versatility and flexibility for multiple applications including residential, light commercial, outdoor and marine use.
QUICK START GUIDE u-line.com This Quick Start Guide covers the basics of installation and general use of your product. CONTENTS Safety and Warning 4 Environmental Requirements 5 Electrical 5 Water Hookup 6 Drain 9 Door Swing 10 Door Adjustments 11 General Installation 17 Control Operation 18 First Use 22 Ice 23 Cleaning 26 Warranty 30 For more details, see the complete User Guide & Service Manual on u-line.com.
QUICK START GUIDE u-line.com Safety and Warning ! DANGER Please read all instructions before installing, operating, or servicing the appliance. Your product may contain R600a (Isobutane) which is a flammable hydrocarbon. To confirm, check serial tag inside of unit. It is safe for Use this appliance for its intended purpose only and follow regular use. Do not use sharp objects to expedite these general precautions with those listed throughout this defrosting.
QUICK START GUIDE u-line.com Environmental Requirements Electrical This unit is designed to operate between 50°F (10°C) and ! WARNING 100°F (38°C). Higher ambient temperatures may reduce the unit’s ability to reach low temperatures and/or reduce SHOCK HAZARD — Electrical Grounding ice production on applicable models. Required. Never attempt to repair or perform maintenance on the unit until the electricity has For best performance, keep the unit out of direct sunlight been disconnected.
QUICK START GUIDE u-line.com Water Hookup ! CAUTION PREPARE PLUMBING Do not use any plastic water supply line. The line The water valve uses a standard 1/4" (6.35 mm) is under pressure at all times. Plastic may crack compression fitting. U-Line recommends using accessory or rupture with age and cause damage to your water hook up kit – part # 80-54674-00. The kit includes a home. 10' (3 m) braided flexible water supply line and a brass hose fitting.
QUICK START GUIDE u-line.com 3. Locate water valve inlet. 9. Install retaining clip. 4. Break away filler feature in bushing with flat screwdriver. CLEAR ICE MACHINES Remove ZLWK ɠDW screwdriver 1. Turn off water supply and disconnect electrical supply to product prior to attempting installation. 5. Thread water line through back panel hole 2. Remove the grille/access panel in the front and the (with bushing). back panel. 6. Locate water valve inlet 3. Locate water and connect to valve.
QUICK START GUIDE u-line.com 4. On the back panel, 3. Thread water line through back panel hole (with break away filler feature bushing). in bushing with flat screwdriver. 3 Remove ZLWK ɠDW screwdriver 5. Thread water line through back panel hole (with bushing) and connect to cold water supply line. 4. Locate water valve inlet and connect to valve. 4 6. Turn on water supply and check for leaks. 7. Reinstall back panel and grille/front access panel. 8. Install retaining clip. 5.
QUICK START GUIDE u-line.com Drain GRAVITY DRAIN CLEAR ICE AND NUGGET ICE MACHINES ONLY Normal Proper Drain Model numbers including “CL” or “NB” do not include a factory installed drain pump. With Trap Poor Drainage, Water Will Back Up Model numbers including “CP” or “NP” include a factory installed drain pump.
QUICK START GUIDE u-line.com FACTORY INSTALLED DRAIN PUMP Y-Branch Tailpiece P60 Pump Required If your drain line will run up to a stand pipe, disposal or Air Gap (Optional Hook-Up) spigot assembly, or does not otherwise meet the requirements for a gravity drain, you may have ordered a pre-installed U-Line P60 drain pump. Waste If you need to install a P60 drain pump into your unit, see 6KXW 2ɞ Valve DRAIN PUMP section in the User Manual.
QUICK START GUIDE u-line.com Door Adjustments 5. Tighten bottom hinge screws. CRESCENT ICE MAKERS 6. Tighten top hinge screws and replace hinge cover. REVERSING THE DOOR HINGE COVER Location of the unit may make it desirable to mount the Hinge cover included with the literature bag is optional. door on the opposite side of the cabinet. To install hinge cover: The hinge hardware will be removed and reinstalled on the Press hinge cover squarely over hinge opposite side of the cabinet.
QUICK START GUIDE u-line.com Install top hinge and door: 4. Remove door by tilting forward and lifting door off bottom hinge. Retain shoulder washers; they will be Top Hinge Right Side reused. 5. Remove three screws from hinge holes on the opposite side. Reinstall into holes where the hinge was Top Hinge Left Side removed. Take care not to scratch cabinet. Pivot Screw Remove bottom hinge: 1. Remove bottom hinge from cabinet using 1/4” socket. 1.
QUICK START GUIDE u-line.com Door Adjustments 5. Tighten bottom hinge screws. 15” REFRIGERATORS AND CLEAR ICE MACHINES 6. Tighten top hinge screws and replace hinge cover. REVERSING THE DOOR HINGE COVER Location of the unit may make it desirable to mount the Hinge cover included with the literature bag is optional. door on the opposite side of the cabinet.
QUICK START GUIDE u-line.com Remove bottom hinge: Install top hinge and door: 1. Remove bottom hinge from cabinet using 1/4” socket. Top Hinge Right Side Top Hinge Left Side Pivot Screw 1. Remove pivot screw from hinge, flip hinge over, and 2. Remove corresponding screws on opposite side of install the pivot screw in the same hole from the cabinet. On some models there may be a nut behind opposite surface. one or both screws on either side.
QUICK START GUIDE u-line.com Door Adjustments 6. Tighten top hinge screws and replace hinge cover. 24” MODELS AND NUGGET ICE MACHINES REVERSING THE DOOR HINGE COVER Hinge cover included with the literature bag is optional. Location of the unit may make it desirable to mount the door on the opposite side of the cabinet. To install hinge cover: The hinge hardware will be removed and reinstalled on the 1. Press hinge cover squarely over hinge. opposite side of the cabinet.
QUICK START GUIDE u-line.com Prepare door for reinstallation: 1. Remove gasket. This will reveal mounting holes for the magnet assembly. 2. Remove magnet assembly from door with T-10 TORX driver. Be sure to only remove the two screws holding the assembly to the door. Reinstall on the opposite end 3. Remove door by tilting forward and lifting door off of the door. bottom hinge. Retain shoulder washers; they will be reused. 3.
QUICK START GUIDE u-line.com General Installation INSTALLATION 1. Plug in the power/electrical cord. LEVELING INFORMATION 1. Use a level to 2. Gently push the unit into position. Be careful not to confirm the unit is entangle the cord or water and drain lines, if level. Level should applicable. be placed along top edge and side edge 3. Re-check the leveling, from front to back and side to as shown. side. Make any necessary adjustments.
QUICK START GUIDE u-line.com Control Operation REFRIGERATORS CONTROL FUNCTION GUIDE FUNCTION COMMAND NOTES ON/OFF Press Unit will turn ON or OFF and hold for 5 seconds Press Leave interior light on and release to leave interior light on for 3 hours; press again to deactivate After 3 hours, factory default is restored; light will turn on when door is open When the display is flashing, press Adjust temperature Press or and release or to adjust the set point temperature.
QUICK START GUIDE u-line.com Control Operation CLEAR ICE MACHINES CONTROL FUNCTION GUIDE FUNCTION COMMAND NOTES ON/OFF Press Unit will immediately turn ON or OFF Adjust ice thickness See “Ice” section Enable Sabbath Mode Disable Sabbath Mode Press and release and hold for 5 seconds and release The oF / oC symbol will flash briefly after 5 seconds.
QUICK START GUIDE u-line.com Control Operation CONVERTIBLE FREEZER CONTROL FUNCTION GUIDE FUNCTION COMMAND NOTES ON/OFF Press and release Unit will immediately turn ON or OFF Press and release to leave interior Leave interior light on light on for 12 hours; press again to deactivate After 12 hours, factory default is restored; light will turn on when door is open When the display is flashing, press Adjust Temperature Press or and release or to adjust the set point temperature.
QUICK START GUIDE u-line.com Control Operation NUGGET ICE MACHINES CONTROL FUNCTION GUIDE FUNCTION COMMAND NOTES ON/OFF Press and release Unit will immediately turn ON or OFF. Press and hold for 5 seconds and Enable Sabbath Mode release. The oF / oC symbol will flash briefly after 5 seconds. Interior light and display will go dark and remain so until user resets mode - unit continues to operate. Disable Sabbath Mode Press and release.
QUICK START GUIDE u-line.com First Use CONVERTIBLE FREEZER CRESCENT ICE MAKERS Initial startup requires no adjustments. If the unit was turned off, press Initial startup requires no adjustments. and the unit will immediately switch on. To turn off, press and release. See CONTROL OPERATION section for more details.
QUICK START GUIDE u-line.com Ice During periods of limited use or high ambient CRESCENT ICE MAKERS Gently shake the bucket to break apart cubes. If not using temperatures, it is common for cubes to fuse together. the ice maker regularly, empty the ice bucket periodically to ensure fresh cubes. ICE MAKER OPERATION When the ice bucket is full, the ice making mechanism will It is normal for cubes to appear cloudy. The cause is air shut off.
QUICK START GUIDE u-line.com CLEAR ICE MACHINES ! CAUTION ICE CUBE THICKNESS ADJUSTMENT Too large of an adjustment to the screw can Ice thickness adjustment should only be made cause the water to overflow the ice maker and one increment at a time. Allow ice maker can cause property damage. production to stabilize for 24 hours before rechecking ice thickness. 3.
QUICK START GUIDE u-line.com NUGGET ICE MACHINES Your clear ice machine is preset to produce ice between the optimal dimensions illustrated below: The Nugget Ice Machine produces cylindrical bits of Cube Details 1/4" TO 1/2" (6.4 mm to 12.7 mm) DIMPLE compressed ice approximately 3/4” x 1/2”. 1/16" TO 1/8" (1.6 mm to 3.2 mm) ICE BRIDGE Ice is produced until the machine senses the bin is full. As ice slowly melts in the bin, the level of ice drops and ice production resumes.
QUICK START GUIDE u-line.com Cleaning ! CAUTION CLEAR ICE MACHINE CLEANING CYCLE Never use anything Your U-Line clear ice machine has an automatic clean Evaporator cover to force ice from the alert function. Cleaning cycles should be run as notified. evaporator. Damage Otherwise, to maintain operational efficiency the unit may result. should be cleaned every three months. Depending on water conditions, more frequent cleaning may be 1. Turn the ice necessary.
QUICK START GUIDE u-line.com • Using a sponge or cloth, clean interior of ice bin, NOTICE tubing and door. This cleaner will remove all mineral Discard all ice produced in the first harvest. deposits and other contaminants from the surfaces. Should power to the unit be interrupted during • Using a bottle brush, clean out the trough drain tube the self-clean cycle, it will be necessary to and pump tubing where needed. repeat the complete cleaning cycle after power is restored.
QUICK START GUIDE You may override u-line.com CL in the display without cleaning by c. Remove all ice in bin pressing and holding the up, down, & light button for 10 d. Remove any ice protruding from the ice dispenser tube ICE will scroll in the display and the cleaning reminder (CL) will be reset for another approximate six seconds. e. Insert the end of the cleaning tube into the ice dispenser; slowly pour in approximately 1 quart of hot water. This will melt ice inside the dispenser tube.
QUICK START GUIDE u-line.com b. Press and release 6. 06 will appear in the display a. Reinstall shield and close door - no further action is required b. The machine will circulate water and perform a series of final rinses for approximately 15 minutes. The unit will resume making ice - indicated by 3 soft tones and ICE scrolling in the display.
U-Line Corporation (U-Line) Limited Warranty One Year Limited Warranty For one year from the date of original purchase, this U-Line product warranty covers all parts and labor to repair or replace any part of the product that proves to be defective in materials or workmanship. For products installed and used for normal residential use, material cosmetic defects are included in this warranty, with coverage limited to 60 days from the date of original purchase.
