USER GUIDE Single and Double Tap Tower Kits RIGHT PRODUCT. RIGHT PLACE. RIGHT TEMPERATURE. SINCE 1962.
WELCOME TO U-LINE Congratulations on your U-Line purchase. Your product comes from a company with over five decades of premium modular ice making, refrigeration, and wine preservation. U-Line continues to be the American leader, delivering versatility and flexibility for multiple applications including residential, light commercial, outdoor and marine use.
Table of Contents Introduction ................................................................................................ 1 Safety and Warning ....................................................................................... 1 Parts Lists .................................................................................................. 2 Tower Installation ......................................................................................... 3 Install on Refrigerator .........................
Introduction U-Line Single and Double Tap Kits are designed to work with the U-Line keg refrigerator model 1224KEGRSOD. Tap kits can be installed directly on top of the keg refrigerator in a free-standing application or through a countertop in a built-in application. The 1224KEGRSOD is designed to fit up to one 1/4 slim barrel and one 1/6 barrel or one standard 1/4 barrel. It does not accept a 1/2 barrel or larger keg. 1/4 Slim Barrel 1/6 Slim Barrel Standard 1/4 Barrel Quarter Slim 7.
Kits include: 1. Single or Double Tower (includes faucet, handle, gasket, wrench, & clamp) 2. Low profile keg coupler (D system for North American Beers) 3. Regulator / CO2 gauge (includes hose and clamps) 4. 5 lb. CO2 cylinder (ships empty) 5. Drip tray 6. Cleaning kit (includes cleaning pump, detergent, faucet brush, washers) 7.
Install Tower on Keg Refrigerator If your keg refrigerator is new out of the box, do not remove the protective film on the stainless exterior until the tower is installed. Note: These instructions are designed for a standard 36" countertop application. 1. Remove four screws and lift off cap plug and gasket to reveal mounting hole on top of refrigerator. Note: Save gasket and cap plug for conversion back to a standard refrigerator. 2.
Install Tower on Countertop (see template at the end of this user guide) 1. Position keg refrigerator under countertop to determine the desired depth. 2. Use the dimensions from Diagram A to determine the centerpoint of the tower mounting hole. 3. Remove keg refrigerator from under countertop. 4. Use template to drill four mounting holes. 5. Drill 2-3/4" diameter hole through countertop. 6. Insert tubing through provided gasket and into 2-3/4" hole. 7. Secure tower to countertop.
CO2 Connection Our CO2 tanks are delivered empty and need to be filled locally. Check online for beverage or home brew supply stores in your area to have your tank filled. 1. Attach regulator to CO2 tank. Hand tighten the coupling nut and then use an adjustable wrench for an additional quarter turn. DO NOT OVER TIGHTEN 2. Attach 5/16” CO2 tubing to regulator nipple and clamp into place. If necessary, make the tubing more pliable by heating the end in boiling water. 3.
Beverage Connection 1. Attach and clamp beverage tubing to tap coupler. 2. Attach tap coupler to keg. Locate notch and rotate clockwise 3. Press down and rotate clockwise an additional 4. Open valve on CO2 tank and adjust regulator to desired pressure by turning the handle clockwise. 1/4 turn 1/4 turn. 1/4 turn.
Setting CO2 Pressure To minimize foam for most beverages the pressure should be set between 8-12 PSI. • Set the pressure by turning the handle on the front of the regulator counterclockwise until it is all the way out. This will turn the regulator off. • Turn the valve on the bottom of the regulator to the side to ensure no CO2 will pass through the regulator. • Pull the pin on the side of the coupler to release built up pressure from the keg. Open the faucet.
Beverage Line Cleaning You will need: 1. Cleaning Kit Included: 1-quart cleaning pump 1 package of cleaning detergent Faucet wrench Faucet brush 2. Clean bucket 3. Fresh water 1. Close CO2 tank. 2. Pull pin on coupler to release pressure from keg. 3. Remove tap coupler from keg. 4. Remove CO2 line from tap coupler. 5. Open tap coupler to allow cleaning solution to flow through it: • Push base of coupler inward and rotate clockwise. 6. Open cleaning pump. 7.
9. Remove faucet from tower with supplied faucet wrench. Disassemble, and place all the parts in drainage bucket. 10. Add washer and attach cleaning pump connector to tower. Tighten with faucet wrench. 11. Pump all the solution through the beverage line. 12. Allow tap coupler and faucet to soak in drainage bucket and then use faucet brush to clean faucet. 13. Rinse out and refill plastic jar with clean water. Pump all the water through the beverage line to rinse. 14.
Potential Draft Issues WILD BEER CLOUDY BEER Description: Description: Beer, when drawn, is all foam, or too much foam and not enough liquid beer.
Warranty / Support U-Line will replace missing or defective components for 60 days from date of purchase. Contact U-Line at +1.800.798.2547. Proof of purchase is required. Additional tap accessories and cleaning solution are available at your local brewing supply store or online. Copyright © 2017 U-Line Corporation. All Rights Reserved. Publication Number 30600 6/2017 Rev.
Template for Countertop Installation 11-15/16 “ TO SIDE OF REFRIGERATOR 1/4” HOLE 2-3/4” HOLE 12-1/2 “ TO FRONT OF REFRIGERATOR 12
