QUICK START GUIDE DISPENSERS • CDE215F (115v) • 1 Tap Beer 30659_B
USER GUIDE QUICK START GUIDE u-line.com u-line.com WELCOME TO U-LINE Congratulations on your U-Line purchase. Your product comes from a company with over five decades of premium modular ice making, refrigeration, and wine preservation experience. U-Line creates products focused on functionality, style, and inspired innovations — paying close attention to even the smallest details. Applications include residential, outdoor, ADA height compliant, marine, and commercial.
QUICK START GUIDE u-line.com This Quick Start Guide covers the basics of installation and general use of your product. CONTENTS Safety and Warning 4 Environmental Requirements 5 Electrical 5 Door Swing 5 Door Adjustments 6 General Installation 8 Control Operation 14 First Use 14 Airflow & Product Loading 16 Cleaning 16 Warranty 20 For more details, see the complete User Guide & Service Manual on u-line.com.
QUICKGUIDE START GUIDE USER u-line.com u-line.com Safety and Warning NOTICE ! DANGER Please read all instructions before installing, operating, or servicing the appliance. Service must be done by factory authorized service personnel. Any parts shall be replaced Use this appliance for its intended purpose only and follow with like components.
QUICK START GUIDE 16-1/2" 90° Door Swing Environmental Requirements 16-1/2" 90° Door Swing u-line.com NOTICE Stainless Black and White Models Electrical installation mustModels observe all state and local codes. This unit requires connection to a This model is intended for indoor/interior applications only 2115WC Models grounded (three-prong), polarized receptacle and is not to be used in installations that are open/ Wall Wall electrician.
QUICK START GUIDE u-line.com Door Adjustments REVERSING THE DOOR HINGE COVER Location of the unit may make it desirable to mount the door on the opposite side of the cabinet. Hinge cover included with the literature bag is optional. The hinge hardware will be removed and reinstalled on the opposite side of the cabinet. To install hinge cover: 1. Press hinge cover squarely over hinge.
QUICK START GUIDE 1. u-line.com Install top hinge and door: Remove door by tilting forward and lifting door off bottom hinge. Retain shoulder washers; they will be reused. 2. Use a Philips screwdriver to remove hinge pin and reinstall on the opposite surface of the hinge. 3. Remove three screws from hinge holes on the opposite side. Reinstall into holes where the hinge was removed. Take care not to scratch cabinet. Remove bottom hinge: 1. Remove bottom hinge from cabinet using a 1/4” socket. 1.
QUICK START GUIDE USER GUIDE u-line.com u-line.com General Installation U-Line Single Tap Kits are designed to work with the U-Line keg refrigerator model CDE215F. Tap kits can be installed directly on top of the keg refrigerator in a free-standing application or through a countertop in a built-in application. The CDE215F is designed to fit one 1/6 barrel. (Not Included) Kit includes: 1. Tower (includes faucet, handle, gasket, wrench, & clamp) 2.
USER GUIDE QUICK START GUIDE u-line.com u-line.com Install Tower on Keg Refrigerator Do not remove the protective film on the stainless exterior until the tower is installed. 1. Remove four screws and lift off cap plug and gasket to reveal mounting hole on top of refrigerator. Note: Save gasket and cap plug for conversion back to a standard refrigerator. 2. Insert tap assembly tubing through the provided gasket and then all the way into the refrigerator. 3.
USER GUIDE QUICK START GUIDE u-line.com u-line.com Install Tower on Countertop (see template at the end of this section) 1. Use template to drill four mounting holes. 2. Drill 2-3/4" diameter hole through countertop. 3. Remove four Phillips screws (secured with nuts on the inside of the refrigerator) and lift off cap to reveal tower mounting hole. 4. Slide keg refrigerator into place. 5. Position gasket over mounting hole. 6. Insert tubing into 2-3/4" hole. 7.
QUICK START GUIDE USER GUIDE u-line.com u-line.com Template for Countertop Installation Note: Verify template has printed true to scale - double check hole dimensions and placement.
USER GUIDE QUICK START GUIDE u-line.com u-line.com CO2 Connection NOTE: Regulator and CO2 tank not included 1. Attach regulator to CO2 tank. Hand tighten the coupling nut and then use an adjustable wrench for an additional quarter turn. DO NOT OVER TIGHTEN 2. Attach 5/16” CO2 tubing to regulator nipple and clamp into place. If necessary, make the tubing more pliable by heating the end in boiling water. 3. Attach and clamp CO2 tubing to tap coupler.
USER QUICKGUIDE START GUIDE u-line.com u-line.com Beverage Connection NOTE: Coupler not included 1. Attach and clamp beverage tubing to tap coupler. 2. Attach tap coupler to keg. Locate notch and rotate clockwise 3. Press down and rotate clockwise an additional 4. Open valve on CO2 tank and adjust regulator to desired pressure by turning the handle clockwise. 1/4 turn. 1/4 1/4 turn turn General Installation 1/4 turn.
QUICK START GUIDE u-line.com Control Operation CONTROL FUNCTION GUIDE FUNCTION COMMAND NOTES ON/OFF Press Unit will turn On or OFF Adjust Temperature Press or Toggle between ºF / ºC Hold and and hold for 5 seconds When the display is flashing, press and release adjust the set point temperature. for 5 seconds The display will change units First Use Initial startup requires no adjustments. If the unit was turned off, press and hold for 5 seconds to turn unit on.
QUICK START GUIDE u-line.com Setting CO2 Pressure To minimize foam for most beverages the pressure should be set between 8-12 PSI. • Set the pressure by turning the handle on the front of the regulator counterclockwise until it is all the way out. This will turn the regulator off. • Turn the valves on the bottom of the regulator to the side to ensure no CO2 will pass through the regulator. • Pull the pin on the sides of the couplers to release built up pressure from the kegs. Open the faucets.
monthly. For best results use Claire® Stainless Steel Polish and Cleaner. Comparable products are acceptable. QUICK START GUIDE Frequent cleaning will remove surface contamination that u-line.com could lead to rust. Some installations may require cleaning weekly. Airflow and Product Loading 4 5 1 Do not clean with steel wool pads. Do not use stainless steel cleaners or polishes on 2 AIRFLOW any glass surfaces. External Clean any glass surfaces with a non-chlorine glass cleaner.
USER QUICKGUIDE START GUIDE u-line.com u-line.com Beverage Line and Faucet Cleaning Clean the system using a suitable solution designed for beerdispensing systems. Beer cleaning kits are also available. Solution and/or kit not included. 1. Close CO2 tank. 2. Pull pin on coupler to release pressure from keg. 3. Remove tap coupler from keg. 4. Remove CO2 line from tap coupler. 5. Open tap coupler to allow cleaning solution to flow through it: • Push base of coupler inward and rotate clockwise. 6.
QUICKGUIDE START GUIDE USER 9. u-line.com Remove faucet from tower with supplied faucet wrench. Disassemble, and place all the parts in drainage bucket. 10. Add washer and attach cleaning pump connector to tower. Tighten with faucet wrench. 11. Pump all the solution through the beverage line. 12. Allow tap coupler and faucet to soak in drainage bucket and then use faucet brush to clean faucet. 13. Rinse out and refill plastic jar with clean water. Pump all the water through the beverage line to rinse.
USER GUIDE QUICK START GUIDE u-line.com u-line.com DEFROSTING Under normal conditions this unit does not require manual defrosting. Minor frost on the rear wall or visible through the evaporator plate vents is normal and will melt during each cycle. If there is excessive build-up of 1/4” (6 mm) or more, manually defrost the unit. Ensure the door is closing and sealing properly. High ambient temperature and excessive humidity can also produce frost.
U-Line Corporation (U-Line) Limited Warranty One Year Limited Warranty For one year from the date of original purchase, this warranty covers all parts and labor to repair or replace any part of the product that proves to be defective in materials or workmanship. For products installed and used for normal residential use, material cosmetic defects are included in this warranty, with coverage limited to 60 days from the date of original purchase.
