Installation Guide CO29A and CO29FF Ice Maker/Refrigerators www.U-LineService.com Phone (414) 354-0300 • FAX (414) 354-7905 Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696 OnlineService@U-Line.
CO29A and CO29FF Ice Maker/Refrigerators Contents Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door Swing/Clearances Information . . . . . . . . . . . . . . Reversing the Door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Other Site Requirements . . . . . . . . . . . . . . . . . . . . . . . .
CO29A and CO29FF Ice Maker/Refrigerators General Precautions 2 Inspect and Plan Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide: You have received a carton containing your CO29A or CO29FF Ice Maker/Refrigerator with a package inside containing a User Manual, a Product Registration Card and water connection parts. Complete and mail the Product Registration Card or register online at www.U-LineService.com.
CO29A and CO29FF Ice Maker/Refrigerators Product Dimensions 3 Prepare Site 24" Including Handle Your U-Line product has been designed for either freestanding or built-in installation. When built-in, your unit does not require additional air space for top, sides or rear. However, the front grille must NOT be obstructed and clearance is required for water and electrical connections in the rear. Note: Unit can NOT be installed behind a closed cabinet door.
CO29A and CO29FF Ice Maker/Refrigerators Reversing the Door Wall All units may be left- or right-hand opening. 1/4" Min. Note: The grille should not yet be installed. If it has been installed, remove it for door reversing. See Page 10. To reverse the door: 21-7/16" 1. Remove top hinge from cabinet (three screws). See Figure 4. Hold door to keep it from falling. 2. Lift the door off the bottom hinge. 22-3/8" 90° Door Swing Right-Hand Hinge Wall or Cabinet 1” Min.
CO29A and CO29FF Ice Maker/Refrigerators 5. Relocate plastic spacer/ bushing on bottom of door to opposite side, and place door on bottom hinge pin. See Figure 8. Clean out bushing hole in door bottom with a screwdriver if necessary. 6. Remove plastic hole plug from door handle and relocate on opposite side. See Figure 9. 10. Fasten upper hinge to unit (three screws). Partially tighten screws. See Figure 11. Bushing 11. Adjust door to assure proper seal. Tighten upper and lower hinge screws securely.
CO29A and CO29FF Ice Maker/Refrigerators 4 Prepare and Install Door Panel Units will accept a Custom 1/4" Thick Insert to harmonize with or accent the surrounding decor. If this treatment is not included in this installation, go on to 5 Adjust Door. Custom 1/4" Thick Door Panel Insert Door Panel Preparation A custom door panel can be inserted into the doorframe. Custom door panels can be flat or raised, as long as the maximum panel thickness where inserted into the door reveal (channel) is 1/4"-thick.
CO29A and CO29FF Ice Maker/Refrigerators 5 Adjust Door 6 Prepare Plumbing CAUTION Checking Door Alignment Plumbing installation must observe all state and local codes. All water connections MUST BE made by a licensed/ qualified plumbing contractor. Failure to follow recommendations and instructions may result in damage and/or harm. The unit’s door is aligned at the factory before shipment. However, its alignment could have been disturbed during shipment or during door panel installation.
CO29A and CO29FF Ice Maker/Refrigerators 7 Prepare Power Supply Electrical Specifications CAUTION Electrical installation must observe all state and local codes. This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a qualified electrician. Water Connection Figure 16 Figure 17 The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A power supply (normal household current).
CO29A and CO29FF Ice Maker/Refrigerators 8 Level the Unit 9 Install the Unit Leveling Information Installation of the CO29A/CO29FF 1. Open the water supply valve in the main water source. IMPORTANT 2. Plug in the power cord. It is extremely important that the unit sits on a level surface, as it does not have feet levelers. If it is not level, the ice mold will not fill evenly. 3. Gently push the unit into position. Be careful not to kink the water supply line or entangle the electrical cord.
CO29A and CO29FF Ice Maker/Refrigerators 10 Start-Up for the First Time Initial Start-Up Grille The unit is shipped with the control preset to a mid-point setting between 4 and 5. Assure that setting was not altered in shipment. No other adjustments should be necessary at this time. For information about Adjusting the Temperature Control, see the User Manual.
Start-Up Troubleshooting Who to Call Q: Problem Service Information Unit does not appear to turn on when plugged in. A: Solution Make sure outlet has power (circuit breaker has not tripped). Be sure that control is not turned to the off position. Make sure the on/off switch is turned on. Q: Problem If the need for service arises, contact the dealer from whom the unit was purchased. State the Model Number and Serial Number and explain the problem.
