™ Installation Guide CO2075DWR — Combo Drawer Model Ice Maker/Refrigerator www.U-LineService.com Phone (414) 354-0300 • FAX (414) 354-7905 Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696 OnlineService@U-Line.
™ CO2075DWR — Ice Maker/Refrigerator Contents Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clearances Information . . . . . . . . . . . . . . . . . . . . . . . . . Other Site Requirements . . . . . . . . . . . . . . . . . . . . . . . . No Custom Drawer Panels . . . . . . . . . . . . . . . . . . . . . . .
™ CO2075DWR — Ice Maker/Refrigerator General Precautions 2 Inspect and Plan Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide: You have received a carton containing your CO2075DWR Combo Drawer Model Ice Maker/Refrigerator with a package inside containing a User Manual, a Product Registration Card, water connection parts and Anti-Tip Kit. Complete and mail the Product Registration Card or register online at www.
™ CO2075DWR — Ice Maker/Refrigerator Exterior Cleaning 3 Prepare Site (As Required) Your U-Line product has been designed for built-in installation. Your unit does not require additional air space for top, sides or rear. However, the front grille must NOT be obstructed and clearance is required for water and electrical connections in the rear. Black Models: • The drawers, grille and cabinet may be cleaned with a mild detergent and warm water solution. Do not use solvent-based or abrasive cleaners.
™ CO2075DWR — Ice Maker/Refrigerator Product Dimensions Clearances Information The unit must be installed in a wall or under a countertop to allow for the installation of the Anti-Tip Kit (see Page 14). 25-13/16" Including Handle 23-11/16" WARNING 34-1/8" The Anti-Tip Kit must be installed on this unit before it is used. Never use the drawers as steps or as a shelf to support more than the drawers’ contents. Serious personal injury could occur.
CO2075DWR — Ice Maker/Refrigerator ™ Other Site Requirements The drawer unit can be installed with an appliance or fixture located in front of it, as long as there is adequate clearance for the drawer to be opened and removed when servicing (see Figure 4). Power Supply The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A circuit (normal household current). See Electrical Specifications on Page 13.
™ CO2075DWR — Ice Maker/Refrigerator Drawer Panel Installation 4 Prepare and Install Drawer Panel Install the insert as follows: (Black Units Only) CAUTION Two types of custom drawer panels can be installed on your Black unit to harmonize with or accent the surrounding décor: Custom 1/4" Inserts or Full Overlays. Black units may also be installed with no custom drawer panel. Use care when handling the insert. Insert edges may be sharp. 1. Open drawer.
™ CO2075DWR — Ice Maker/Refrigerator Full Overlay Drawer Panels Attaching the Full Overlay Panel Drawer Panel Preparation 1. If user-supplied cabinet handles will be used, attach their hardware to the overlay panel at this time. Full overlay drawer panels completely cover the drawer fronts and handles to give a built-in appearance. Black units are shipped ready for full overlay installation.
™ CO2075DWR — Ice Maker/Refrigerator CAUTION 5 Adjust Drawers It is important to ensure that all drilled holes are drilled to the correct depth in order to avoid splits in the wood when hardware is installed. Checking Drawer Alignment The unit’s drawers are aligned at the factory before shipment. However, their alignment could have been disturbed during shipment or during overlay panel installation. 4. Remove tape adjoining the panels and enlarge the five holes in the overlay panel using a 0.
™ CO2075DWR — Ice Maker/Refrigerator Adjusting Drawer Alignment Minor Adjustment: Note: The mounting holes on the slide are slightly larger than the screws’ diameter. WARNING SHOCK HAZARD — The unit must be unplugged from the wall outlet during drawer removal, adjustment and re-installation. 1. Loosen the slide’s mounting screws. Drawer Removal 2. Push the slide backward. 1. Confirm that the unit is unplugged from wall outlet. Mounting Screw Push Slide Backward 3. Retighten the screws.
™ CO2075DWR — Ice Maker/Refrigerator Minor Adjustment: Minor Adjustment: Note: The mounting holes on the slide are slightly larger than the screws’ diameter. Note: The mounting holes on the slide are slightly larger than the screws’ diameter. Screws Should Be Loose 1. Loosen one slide’s mounting screws. 1. Loosen one slide’s mounting screws. 2. Level the slide. 2. Push the slide upward or downward to match the position of the other slide. 3. Retighten the screws. See Figure 18. 4.
™ CO2075DWR — Ice Maker/Refrigerator 2. Locate the compression fitting and ferrule packed with the unit. Slide the compression fitting and ferrule over the 1/4-inch OD water supply line. Do not use thread sealing compound or tape. Using two wrenches, tighten the compression fitting on the supply line (see Figure 24). 6 Prepare Plumbing Plumbing installation must observe all state and local codes. All water connections MUST BE made by a licensed/ qualified plumbing contractor.
™ CO2075DWR — Ice Maker/Refrigerator 7 Prepare Power Supply 8 Level the Unit Electrical Specifications Leveling Information CAUTION IMPORTANT It is extremely important that the unit is level. If it is not level, the ice mold will not fill evenly. Electrical installation must observe all state and local codes. This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a qualified electrician. 1.
™ CO2075DWR — Ice Maker/Refrigerator 9 Install the Unit Horizontal Mounting (Left Side Shown) Countertop or Wall Header Installation of the CO2075DWR 1. Make sure the ON/OFF switch is in the OFF position. 2. Open the water supply valve in the main water source. B 3. Plug in the power cord. 4. Gently push the unit into position. Be careful not to kink the water supply line or entangle the electrical cord. A 5. Re-check the leveling, from front to back and side to side.
™ CO2075DWR — Ice Maker/Refrigerator 4. Using two of the screws (C) supplied, fasten the screws through the bracket and into the counter, cabinet or wall. 10 Start-Up for the First Time IMPORTANT Initial Start-Up Certain cabinets or countertops may require special fasteners or additional wood blocking to anchor properly. Once installation and leveling is complete, the unit is ready for initial start-up and operation. The ON/OFF switch is located in the front grille (see Figure 30).
™ CO2075DWR — Ice Maker/Refrigerator Start-Up Troubleshooting Temperature Controller The temperature controller (Figure 32) is located in the top drawer. It consists of an LED display, two LED status indicator lights and three touchpad buttons. The LED display shows the refrigerator temperature set point and is calibrated in degrees Fahrenheit. The controller is factory programmed for a set point of 38°F for the top drawer which will show when the unit is first powered up.
™ Who to Call Service Information If the need for service arises, contact the dealer from whom the unit was purchased. State the Model Number and Serial Number and explain the problem. The Model and Serial Number plate is located inside unit at upper right hand corner. If you need to locate a service company, you can go online at www.U-LineService.com and search for a service company by zip code.
