INSTALLATION GUIDE ® MODULAR 3000 SERIES WINE CAPTAIN® MODELS BEVERAGE CENTERS GLASS DOOR REFRIGERATORS REFRIGERATORS U-3018WCOL-00 U-3024BEVOL-00 U-3018RGLOL-00 U-3018RFOL-00 U-3018WCOL-01 U-3024BEVOL-01 U-3018RGLOL-01 U-3018RFOL-01 U-3018WCS-00 U-3024BEVS-00 U-3018RGLS-00 U-3018RFS-00 U-3018WCS-01 U-3024BEVS-01 U-3018RGLS-01 U-3018RFS-01 U-3018WCS-13 U-3036BVWCOL-00 U-3018RGLS-13 U-3024RFOL-00 U-3018WCS-15 U-3036BVWCS-00 U-3018RGLS-15 U-3024RFOL-01 U-3024WCOL-00 U-3036BVWCS
Table of Contents 1 - Safety Precautions Safety Alert Definitions ........................................................................................................................................ 1 General Precautions.............................................................................................................................................. 1 2 - Inspect & Plan Product Registration .......................................................................................................
General Precautions 1 General Information Use this appliance for its intended purpose only and follow these general precautions with those listed throughout this guide: NOTICE • PLEASE READ all instructions before installing, operating, or servicing the appliance. • Proper installation procedures must be followed when completing an installation or relocation of a unit. An INSTALLATION GUIDE for the unit, providing complete installation information, is available from ULine Corporation direct.
Exterior Cleaning 2 Inspect & Plan NOTICE Stainless door panels, handles and frames can discolor when exposed to chlorine gas, pool chemicals, salt water or cleaners with bleach. Product Registration You have received a carton containing your 3000 series unit with a package inside containing a Quick Start Guide and a Registration Card. Please complete and mail the Product Registration Card. You may also register the unit online at u-line.com.
Cut-Out Dimensions 3 Prepare Site 3018 Series Your U-Line product has been designed exclusively for a built-in installation. When built-in, your unit does not require additional air space for top, sides, or rear. However, the front grille must NOT be obstructed. The Modular 3000 Series units are engineered with a variety of adjustment features to help ensure a seamless installation. adjustable doors, leveling legs and grille will assist in fine tuning the installation.
3018, 3024 & 3036 Series 4 Product Dimensions 3024 Series 3018 Series 3036 Series 22-11/16" 22-11/16" 33-11/16" To 34-11/16" 33-11/16" To 34-11/16" 3-5/8" To 4-5/8" 17-3/4" 22-11/16" 3-5/8" To 4-5/8" 33-11/16" To 34-11/16" 23-5/8" 35-7/16" 3-5/8" To 4-5/8" Glass & Solid Overlay Glass & Solid Overlay Glass & Solid Overlay 23-7/16" 23-7/16" 23-7/16" 33-11/16" To 34-11/16" 33-11/16" To 34-11/16" 33-11/16" To 34-11/16" 3-5/8" To 4-5/8" 3-5/8" To 4-5/8" 23-5/8" 35-7/16" 3-5/8" To 4-5/8
Other Site Requirements 5 Door Swing Dimensions Side-By-Side Installation Units have a zero clearance when the door to open 90°. Overlay models will need additional space for any knobs or pulls installed on the overlay panel / frame. Stainless Steel models require 2" door clearance to accommodate the handle if installed next to a wall. Wall Cut-out width for a side-by-side installation is the total of the widths listed under Cut-Out Dimensions in each unit’s Installation Guide. No trim kit is required.
3. Gently pull bottom of wrap away from door. 6 3000 Series Doors 4. The Wrap hinges on top of the door. Carefully pull wrap away and then up. See below. Door Alignment and Adjustment Align and adjust the door if it is not level, or is not sealing properly. If the door is not sealed the unit may not cool properly, or excessive frost or condensation may form in the interior.
7 3000 Series Overlays NOTICE Overlay / Frame Overlay Panel NOTICE • The door panel must not weigh more than 20 lbs (9.1 kg). • It is important to ensure that all drilled holes are drilled to the correct depth in order to avoid splits in the wood when hardware is installed. Appliance will need up to 34-1/2" (876 mm) to the under side of the counter to leave room for leveling adjustments. • Due to differences in surrounding cabinetry the panel may not perfectly align with door.
3024 Models BACK SURFACE MUST HAVE AMPLE FLAT SURFACE TO MOUNT OVERLAY PANEL FLAT AND WITHOUT INTERFERENCE 3/4" (19 mm) BACK SURFACE MUST HAVE AMPLE FLAT SURFACE TO MOUNT OVERLAY FRAME FLAT AND WITHOUT INTERFERENCE 23-3/8" (594 mm) 23-3/8" (594 mm) 2-3/4" MIN (70 mm MIN) 30" (762 mm) Solid Overlay 2. Starting at corner, pull gasket away from door. NOTICE If working with the door that houses the display, make certain the display cable remains securely seated in the inner door channel, see below. 3.
5. The frame should be aligned with the outside edge (opposite the hinge) and high enough to align with the highest point in the door. 10. Be sure the screws force their way past the opening on the gasket channel and sit flush against the bottom of the channel. Align Top Of Panel With Highest Point Of Door Align Frame Against Door Edge First Overlay Panel Overlay Panel 11. Remove clamps from door.
1-1/2" 1-1/2" 1-1/2" 10 u-line.
3036 Side Mount 8 3000 Series Anti-Tip Bracket Side mount configurations work well if you have a granite countertop or do not wish to mount the brackets to the underside of your countertop. Anti-Tip Brackets Installation 1. Align each bracket to the side mounting holes on the hinge side of your model as shown below. ! CAUTION The anti-tip bracket must be installed to prevent the unit from tipping when doors are fully opened, or excess weight is placed on the front of the unit.
3018/3024 Top Mount 3018/3024 Side Mount Left View Of Cabinet Right View Of Cabinet Top mount configurations work well with fully secured wood or laminate countertops. 1. Align the bracket on top of your unit as shown above. The bracket must be used to ensure a secure mount. 2. Using 2 of the supplied 10 #8 5/8" screws, install screws into the plate using a #2 Phillips head screwdriver. 3. Completely slide the unit into its position in the cabinet. Be certain unit height is properly adjusted.
9 Installation 9 Level & Install 1. Plug in the powercord. Leveling Information 2. Gently push the unit into position. Be careful to not entangle the electrical cord. It is recommended that the unit is level once installed. 1. Use a level to check the levelness of the unit from front to back and from side to side. Level should be placed along top edge and side edge as shown. 3. Re-check the leveling, from front to back and side to side. Make any necessary adjustments.
INSTALLATION GUIDE ® PRODUCT INFORMATION Complete Installation Guides, Use and Care Guides, Specifications & Features and Benefits, CAD Drawings, Overlay Panel/Frame and Toe-Kick Specifications and Instructions, Compliance Documentation and Applicable Energy Guides are available for reference and download at u-line.com. SERVICE INFORMATION Please consult your Use and Care Guide for troubleshooting information. Answers to Customer Frequently Asked Questions are available at u-line.
