Installation Guide 2275DWRR — Refrigerator Drawer www.U-LineService.com Phone (414) 354-0300 • FAX (414) 354-7905 Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696 OnlineService@U-Line.
275DWRR — Drawer Model Refrigerator Contents Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clearances Information . . . . . . . . . . . . . . . . . . . . . . . . . Other Site Requirements . . . . . . . . . . . . . . . . . . . . . . . . No Custom Drawer Panels . . . . . . . . . . . . . . . . . . . . . . .
2275DWRR — Drawer Model Refrigerator General Precautions 2 Inspect and Plan Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide: You have received a carton containing your 2275DWRR Drawer Model Refrigerator with a package inside containing a Use and Care Guide, a Product Registration Card and Anti-Tip Kit. Complete and mail the Product Registration Card or register online at www.U-LineService.com.
2275DWRR — Drawer Model Refrigerator Exterior Cleaning 3 Prepare Site (As Required) Your U-Line product has been designed for built-in installation. Your unit does not require additional air space for top, sides or rear. However, the front grille must NOT be obstructed and clearance is required for electrical connection in the rear. Overlay Models: • The drawers, grille and cabinet may be cleaned with a mild detergent and warm water solution. Do not use solvent-based or abrasive cleaners.
2275DWRR — Drawer Model Refrigerator Product Dimensions Clearances Information The unit must be installed in a wall or under a countertop to allow for the installation of the Anti-Tip Kit (see Page 13). 25-13/16" Including Handle 23-11/16" WARNING 34-1/8" The Anti-Tip Kit must be installed on this unit before it is used. Never use the drawers as steps or as a shelf to support more than the drawers’ contents. Serious personal injury could occur.
2275DWRR — Drawer Model Refrigerator Other Site Requirements The drawer unit can be installed with an appliance or fixture located in front of it, as long as there is adequate clearance for the drawer to be opened and removed when servicing (see Figure 4). Power Supply The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A circuit (normal household current). See Electrical Specifications on Page 12.
2275DWRR — Drawer Model Refrigerator Drawer Panel Installation 4 Prepare and Install Drawer Panel Install the insert as follows: (Overlay Units Only) CAUTION The Overlay unit comes standard out of the factory ready to accept the 3/4” Full Overlay Panels. Use care when handling the insert. Insert edges may be sharp. Two types of custom drawer panels can be installed on your Overlay unit to harmonize with or accent the surrounding décor: Custom 1/4" Inserts or Full Overlays.
2275DWRR — Drawer Model Refrigerator Full Overlay Drawer Panels Attaching the Full Overlay Panel Drawer Panel Preparation 1. If user-supplied cabinet handles will be used, attach their hardware to the overlay panel at this time. Full overlay drawer panels completely cover the drawer fronts and handles to give a built-in appearance. Overlay units are shipped ready for Full Overlay installation.
2275DWRR — Drawer Model Refrigerator CAUTION 5 Adjust Drawers It is important to ensure that all drilled holes are drilled to the correct depth in order to avoid splits in the wood when hardware is installed. Checking Drawer Alignment The unit’s drawers are aligned at the factory before shipment. However, their alignment could have been disturbed during shipment or during overlay panel installation. 4. Remove tape adjoining the panels and enlarge the five holes in the overlay panel using a 0.
2275DWRR — Drawer Model Refrigerator Adjusting Drawer Alignment Minor Adjustment: Note: The mounting holes on the slide are slightly larger than the screws’ diameter. WARNING SHOCK HAZARD — The unit must be unplugged from the wall outlet during drawer removal, adjustment and re-installation. 1. Loosen the slide’s mounting screws. Drawer Removal 2. Push the slide backward. 1. Confirm that the unit is unplugged from wall outlet. Mounting Screw Push Slide Backward 3. Retighten the screws.
2275DWRR — Drawer Model Refrigerator Minor Adjustment: Minor Adjustment: Note: The mounting holes on the slide are slightly larger than the screws’ diameter. Note: The mounting holes on the slide are slightly larger than the screws’ diameter. Screws Should Be Loose 1. Loosen one slide’s mounting screws. 1. Loosen one slide’s mounting screws. 2. Level the slide. 2. Push the slide upward or downward to match the position of the other slide. 3. Retighten the screws. See Figure 18. 4.
2275DWRR — Drawer Model Refrigerator 6 Prepare Power Supply 7 Level the Unit Electrical Specifications Leveling Information Note: It is recommended that the unit is level. CAUTION 1. Use a level to check the levelness of the unit from front to back and from side to side. Level should be placed along top edge and side edge as shown (see Figure 24). Electrical installation must observe all state and local codes.
2275DWRR — Drawer Model Refrigerator 8 Install the Unit Horizontal Mounting (Left Side Shown) Countertop or Wall Header Installation of the 2275DWRR 1. Plug in the power cord. B 2. Open the top drawer and press the POWER icon to turn the unit off. (see Figure 27,1 page 14) 3. Gently push the unit into position. Be careful not to entangle the electrical cord. A 4. Re-check the leveling, from front to back and side to side. Make any necessary adjustments.
2275DWRR — Drawer Model Refrigerator 4. Using two of the screws (C) supplied, fasten the screws through the bracket and into the counter, cabinet or wall. 9 Start-Up for the First Time IMPORTANT Initial Start-Up Certain cabinets or countertops may require special fasteners or additional wood blocking to anchor properly. Once installation and leveling is complete, the unit is ready for initial start-up and operation.
Start-Up Troubleshooting Who to Call Q: Service Information Problem Unit does not appear to turn on POWER icon is pressed. A: Solution Make sure unit is plugged in and outlet has power (circuit breaker has not tripped). IMPORTANT See the Use and Care Guide’s Troubleshooting Guide for more solutions. If the need for service arises, call the U-Line Customer Care Center directly @ 800-779-2547.
