Use and Care Guide Refrigerator Models: 1115R, 1175R, 29R Beverage Center Model: 1175BEV 29R 1115R 1175BEV 1175R
1 Introduction Congratulations on your purchase of a U-Line refrigeration product. A pioneer in the field for more than 40 years, U-Line Corporation is the world’s number one manufacturer of built-in, under-counter, specialty refrigeration and ice making products. U-Line dedicates 100% of its research and development to these products. The result: U-Line technology consistently leads the market with innovation, design, depth of product line and performance.
2 Table of Contents Introduction ...............................................................................................................................2 Warranty Registration .......................................................................................................2 Please Record Your Model Information ...........................................................................2 Table of Contents ...........................................................................................
This page intentionally left blank 4 1115R, 1175R, 29R, 1175BEV
WARNING 3 Safety Precautions IMPORTANT PLEASE READ all instructions completely before attempting to install, operate, or service your unit. • Proper installation procedures must be followed if this unit is being initially installed, or is moved to a new location after being in service. An INSTALLATION GUIDE for your unit, providing complete installation information is available from U-Line Corporation directly, and must be consulted before any installation is begun.
Origins Beverage Center Model 1175BEV 4 Product Features Origins Refrigerator Models 1115R, 1175R, 29R • Models 1115R and 1175R feature an electronic control panel with digital display that allows you to display the interior temperature and adjust the setting to your preference. The electronic control and digital display provide an attractive appearance and its method of control permits precise temperature settings. Model 29R is equipped with a manual temperature control.
Interior Lighting 5 Operation Model 1115R, 1175R and 1175BEV The interior of the cabinet can be illuminated whenever the door is opened or remained darkened for a 36-hour period (blackout/Sabbath mode [not Star K certified]). 1 2 3 4 5 ULIN_0126_A Figure 2 IMPORTANT Proper air flow (Figure 2) is required for your unit to operate at its highest efficiently. A grille, located in the base of the unit, must not be blocked at any time, or your unit will not perform as expected.
Electronic Control Panel 1 2 3 Checking Product Temperature 4 5 ULIN_0074_A Figure 5 Models 1115R, 1175R and 1175BEV The electronic control with digital display (Figure 5) is configured to show a single temperature continuously. This set-point temperature is a base number used by the controller to maintain the temperature zone in your unit. The factory default set-point is 38°F. This set-point temperature is used as a gauge if further temperature adjustments are required.
Manual Temperature Control Adjusting Temperature Model 29R IMPORTANT Adjust the set point temperature in single increments, and wait 24 hours for the temperature to stabilize before rechecking. 1 2 3 4 1 5 ULIN_0014_A Figure 8 ULIN_0074_A Figure 7 To adjust the set point temperature: 1. Press and release either the WARMER (Figure 7, 4) or COOLER (Figure 7, 5) button to put the controller in the SET TEMPERATURE mode. The °F (or °C) symbol will begin to flash.
Wine Stocking Recommendations Storage, Vacation, Moving Model 1175BEV If the unit will not be used for an extended period, or otherwise stored, follow these steps completely: Specially designed wine racks allow for the proper horizontal storage of wine. The bottles are properly positioned so the wine remains in contact with the cork to assure that the cork does not become dry. The wine racks should be stocked staggering the bottles as shown (Figure 9). WARNING Electrical Shock Hazard.
Suggestions for Matching Food and Wine 6 Wine Guide Wine Recommendations To most, wine is a delicious mystery. We purchase it, uncork it, and savor its taste and beauty. But there is so much more to true wine appreciation. Many secrets are simply too good to keep bottled up. The U-Line Corporation is proud to present Spilling Wine Secrets online at www.U-Line.com/resources/wine_secrets.
Guide to Common Styles of Wine Red Wines Full-Bodied Dry California French Italian Zinfandel, Cabernet Rhone, Chateauneuf-du-Pape Barbaresco, Barolo Medium-Bodied Dry California French Pinot Noir Bordeaux, Burgundy Light-Bodied Dry French Italian Beaujolais Chianti, Bardolino Full-Bodied Dry California French Chardonnay Montrachet, Meursault Puligny-Montrachet Medium-Bodied Dry California French Sauvignon-Blanc Pouilly-Fuisse, Sancerre, Vouvray, Graves Light-Bodied Dry French Chablis, Musca
7 Cleaning and Maintenance General Cleaning • Do not use any solvent-based or abrasive cleaners. These types of cleaners may transmit taste to the interior products and damage or discolor the interior. Maintenance Exterior Cleaning (As Required) Vinyl Clad (Black or White) Models: • Surfaces may be cleaned with a mild detergent and warm water solution. Do not use solvent-based or abrasive cleaners. Use a soft sponge and rinse with clean water. Wipe with a soft, clean towel to prevent water spotting.
To defrost: 4. Remove grille and grille cap from unit. 1. Turn unit off. 1 2. Remove all products from the interior and prop the door in an open position (2 in. (5 cm) minimum). 3. Allow the frost to completely melt naturally. Clean the interior and all removed components using a mild nonabrasive detergent and warm water solution applied with a soft sponge or non-abrasive cloth. NOTE: DO NOT use any solvent-based or abrasive cleaners. They will discolor or damage the interior. 4.
1 1 2 ULIN_0156_A Figure 15 3 4. Clean the condenser coil (Figure 15, 1) using a using a soft brush with a “combing” action or vacuum cleaner. Do not touch the condenser coil. ULIN_0159_A Figure 18 5. Place the hook-hinge (Figure 18, 1) located on the rear bottom side of the grille onto the front lip (Figure 18, 2) of the unit base. Swing the grille up into position, and align the screw holes on the grille to the grille screw hole on the cabinet. 6.
Door Reversal Black or white unit doors may be left- or right-hand opening. Depending upon the location of the unit, it may be desirable to change the side on which the door is mounted. Black Model 1115R To reverse the door, perform the following: 1 ULIN_0042_A 1. Remove the grille and grille cap (two screws). Figure 20 2. If the unit is not level, adjust the feet on the corners of the unit as necessary (Figure 20). 3.
7. Relocate plastic spacer/bushing (Figure 26) on bottom of door to opposite side, and place door on bottom hinge pin. Clean out bushing hole in door bottom with a screwdriver if necessary. Hinge Plastic Plug Hole Plastic Plug Hole Screw Right Side Door Swing Left Side Door Swing Right Side Hinge ULIN_0122_A Invert Screw Invert Hinge ULIN_0142_A Figure 24 Figure 27 5. Remove screws on opposite side of cabinet (Figure 24). Note that there may be a nut behind one or both screws on either side. 8.
12. Fasten upper hinge to unit (three screws) (Figure 29). Partially tighten screws. 13. Adjust door to assure proper seal. Tighten upper and lower hinge screws securely. Hinge Plastic Plug Hole Plastic Plug Hole 14. Replace three plastic plugs removed in Step 10 into holes on top of unit. Replace screws in holes in bottom of unit on opposite side. 15. Replace the grille and grille cap. Be sure to place grille cap on opposite side of unit from where it was originally.
2. Remove two screws from grille (Figure 37, 2) and save. 3. Remove the grille and grille cap from unit. 1 ULIN_0109_A Figure 35 9. Relocate plastic spacer/bushing (Figure 35) on bottom of door to the opposite side. Clean out bushing hole in door bottom if necessary. ULIN_0143_A Figure 38 4. Remove top hinge from cabinet (three screws) (Figure 38). Hold door to keep it from falling. 5. Lift the door off the bottom hinge. ULIN_0110_A Figure 36 10. Place door on lower hinge pin.
9. Relocate plastic spacer/bushing (Figure 42, 1) on bottom of door to opposite side, and place door on bottom hinge pin. Clean out bushing hole in door bottom with a screwdriver if needed. Hinge Plastic Plug Hole Plastic Plug Hole Screw Right Side Door Swing Left Side Door Swing Right Side Hinge ULIN_0122_A Invert Screw Invert Hinge ULIN_0142_A Figure 40 Figure 43 7. Remove screws on opposite side of cabinet (Figure 40). Note that there may be a nut behind one or both screws on either side. 10.
Door Shelf Removal/Insertion 1 2 ULIN_0143_A Figure 45 ULIN_0040_A 14. Fasten upper hinge to unit (three screws) (Figure 45). Partially tighten screws until door is aligned. Figure 47 15. Adjust door to assure proper seal. Tighten upper hinge screws securely. NOTE: 1115R and 1175R models only 16. Replace three plastic plugs removed in Step 11 into holes on top of unit. Replace screws in holes in bottom of unit, opposite side. 1.
Glass Shelf Removal/Installation 2. Tilt up right-hand edge of shelf (Figure 49, 2). 3. Remove shelf from unit by pulling out (Figure 49, 3). Insert the shelves as follows: 1. To move to a different position in the unit, insert shelf at an angle, approximately 15-20°, over the rib in the side of the unit where you want to place the shelf. The shelf must be started into the unit at an angle to clear the door. 2. Continue to slide the shelf into the unit at an angle until it clears the door. 1 3.
Wine Rack Removal/Installation Wood Trim Finishing 1175BEV Interior components of your U-Line unit are equipped with a natural wood trim for appearance and durability. Although this wood trim has been coated with a clear sealer at the factory, it is recommended that the trim be stained (if desired), and receive a final finish coating prior to the unit going into full-time service. To remove a rack from the cabinet: 1. Grasp the end of the rack, and gently slide it out until it stops. 2.
6. Remove all dust from the wood, and apply one coat of Minwax® Polycrylic® Protective Finish using a synthetic bristle brush to the wood. This finish should be applied in a thin coat following the direction of the grain. Apply the finish to the back and sides of the wood first, and allow it to dry for two hours. Apply the finish to the front side of the wood next, and allow it to dry for two hours. Sand with very fine 220 grit sandpaper.
Troubleshooting Guide NOTE: Recommended temperature setting is 38°. DANGER ELECTROCUTION HAZARD Never attempt to repair or perform maintenance on the unit until the main electrical power has been disconnected. Troubleshooting - What to check when problems occur: PROBLEM POSSIBLE CAUSE REMEDY Unit does not operate and electronic display is blank. No electrical supply Plug unit in or check circuit breaker.
Troubleshooting - Models with an electronic display: PROBLEM POSSIBLE CAUSE REMEDY Electronic display is blank and interior light is off with door open. Unit is in blackout/Sabbath mode (not Star K certified). Exit blackout/Sabbath mode (not Star K certified) (See OPERATION). Electronic display is blank and interior light is on with door open. A display function has changed. Touch and hold the WARMER button and touch and release the ON/OFF button three times, then release the temperature button.
Electronic Control Quick Guide Task Turn ON/OFF Adjust Temperature Touch ON/ OFF WARMER Hold 10 seconds or COOLER Touch and release View Actual Temp WARMER Change F/C Hold 5 seconds Hold Blackout Mode Touch Display Release when °F flashes. or WARMER or °F flashes after first touch, set-point saved after 5 seconds of inactivity and °F stops flashing. COOLER Touch to change temperature WC models will scroll top/mid/bottom temps. Release when °F flashes.
This page intentionally left blank 28 1115R, 1175R, 29R, 1175BEV
This page intentionally left blank 1115R, 1175R, 29R, 1175BEV 29
This page intentionally left blank 30 1115R, 1175R, 29R, 1175BEV
U-Line Corporation Limited Warranty U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from defects in materials and workmanship for a period of five years from the date of purchase.
For General Inquiries: P.O. Box 245040 Milwaukee, Wisconsin 53224-9540 U.S.A. Phone (800) 779-2547 FAX (414) 354-5696 www.U-Line.com For Service and Parts Assistance: Phone (800) 779-2547 (414) 354-0300 FAX (414) 354-5696 Email: OnLineService@U-Line.com www.U-LineService.com E-mail: OnlineParts@u-line.com For more than four decades, U-Line has distinguished itself as the leader in built-in under-counter ice making, refrigeration and wine storage appliances.
