Integration Manual
Table Of Contents
- Document information
- Contents
- 1 System description
- 1.1 Overview
- 1.2 Architecture
- 1.3 Pin-out
- 1.4 Operating modes
- 1.5 Supply interfaces
- 1.5.1 Module supply input (VCC)
- 1.5.1.1 VCC supply requirements
- 1.5.1.2 VCC current consumption in LTE connected mode
- 1.5.1.3 VCC consumption in deep-sleep mode (low power mode and PSM enabled)
- 1.5.1.4 VCC current consumption in low power idle mode (low power mode enabled)
- 1.5.1.5 VCC current consumption in active mode (low power mode and PSM disabled)
- 1.5.2 Generic digital interfaces supply output (V_INT)
- 1.5.1 Module supply input (VCC)
- 1.6 System function interfaces
- 1.7 Antenna interfaces
- 1.8 SIM interface
- 1.9 Data communication interfaces
- 1.10 Audio
- 1.11 General purpose input / output (GPIO)
- 1.12 Reserved pin (RSVD)
- 2 Design-in
- 2.1 Overview
- 2.2 Supply interfaces
- 2.2.1 Module supply (VCC)
- 2.2.1.1 General guidelines for VCC supply circuit selection and design
- 2.2.1.2 Guidelines for VCC supply circuit design using a switching regulator
- 2.2.1.3 Guidelines for VCC supply circuit design using low drop-out linear regulator
- 2.2.1.4 Guidelines for VCC supply circuit design using a rechargeable battery
- 2.2.1.5 Guidelines for VCC supply circuit design using a primary battery
- 2.2.1.6 Guidelines for external battery charging circuit
- 2.2.1.7 Guidelines for external charging and power path management circuit
- 2.2.1.8 Guidelines for removing VCC supply
- 2.2.1.9 Additional guidelines for VCC supply circuit design
- 2.2.1.10 Guidelines for VCC supply layout design
- 2.2.1.11 Guidelines for grounding layout design
- 2.2.2 Generic digital interfaces supply output (V_INT)
- 2.2.1 Module supply (VCC)
- 2.3 System functions interfaces
- 2.4 Antenna interfaces
- 2.5 SIM interface
- 2.6 Data communication interfaces
- 2.6.1 UART interfaces
- 2.6.1.1 Guidelines for UART circuit design
- Providing 1 UART with the full RS-232 functionality (using the complete V.24 link)
- Providing 1 UART with the TXD, RXD, RTS, CTS, DTR and RI lines only
- Providing 1 UART with the TXD, RXD, RTS and CTS lines only
- Providing 2 UARTs with the TXD, RXD, RTS and CTS lines only
- Providing 1 UART with the TXD and RXD lines only
- Providing 2 UARTs with the TXD and RXD lines only
- Additional considerations
- 2.6.1.2 Guidelines for UART layout design
- 2.6.1.1 Guidelines for UART circuit design
- 2.6.2 USB interface
- 2.6.3 SPI interfaces
- 2.6.4 SDIO interface
- 2.6.5 DDC (I2C) interface
- 2.6.1 UART interfaces
- 2.7 Audio
- 2.8 General purpose input / output (GPIO)
- 2.9 Reserved pin (RSVD)
- 2.10 Module placement
- 2.11 Module footprint and paste mask
- 2.12 Schematic for SARA-R5 series module integration
- 2.13 Design-in checklist
- 3 Handling and soldering
- 4 Approvals
- 5 Product testing
- Appendix
- A Migration between SARA modules
- B Glossary
- Related documents
- Revision history
- Contact
SARA-R5 series - System integration manual
UBX-19041356 - R03 System description Page 28 of 123
Confidential
1.7.2 GNSS antenna RF interface (ANT_GNSS)
☞ The GNSS antenna RF interface is not supported by SARA-R500S and SARA-R510S modules.
SARA-R510M8S modules provide an RF interface for connecting the external GNSS antenna. The
ANT_GNSS pin represents the RF input reception of GNSS RF signals.
The ANT_GNSS pin has a nominal characteristic impedance of 50 and must be connected to the Rx
GNSS antenna through a 50 transmission line to allow proper RF reception. As shown in Figure 4,
the GNSS RF interface is designed with an internal DC block, and is suitable for both active and/or
passive GNSS antennas due to the built-in SAW filter followed by an additional LNA in front of the
integrated high performing u-blox M8 concurrent position engine.
1.7.2.1 GNSS antenna RF interface requirements
Table 7 summarizes the requirements for the GNSS antenna RF interface. See section 2.4.3 for
suggestions to correctly design antennas circuits compliant with these requirements.
Item
Requirements
Remarks
Impedance
50 nominal characteristic impedance
The impedance of the antenna RF connection must match the
50 impedance of the ANT_GNSS port.
Frequency range
BeiDou 1561 MHz
GPS / SBAS / QZSS / Galileo 1575 MHz
GLONASS 1602 MHz
The required frequency range of the antenna connected to
ANT_GNSS port depends on the selected GNSS constellations.
Return loss
S
11
< -10 dB (VSWR < 2:1) recommended
S
11
< -6 dB (VSWR < 3:1) acceptable
The return loss or the S
11
, as the VSWR, refers to the amount of
reflected power, measuring how well the antenna RF connection
matches the 50 characteristic impedance of the ANT_GNSS
port.
The impedance of the antenna termination must match as
much as possible the 50 nominal impedance of the
ANT_GNSS port over the operating frequency range, reducing
as much as possible the amount of reflected power.
Gain
(passive antenna)
> 4 dBic
The antenna gain defines how efficient the antenna is at
receiving the signal. It is important providing good antenna
visibility to the sky, using antennas with good radiation pattern
in the sky direction, according to related antenna placement.
Gain
(active antenna)
17 dB minimum, 30 dB maximum
The antenna gain defines how efficient the antenna is at
receiving the signal. It is directly related to the overall C/No.
Noise figure
(active antenna)
< 2 dB
Since GNSS signals are very weak, any amount of noise
degrades all the sensitivity figures of the receiver: active
antennas with LNA with a low noise figure are recommended.
Axial ratio
< 3 dB recommended
GNSS signals are circularly-polarized. The purity of the antenna
circular polarization is stated in terms of axial ratio (AR),
defined as the ratio of the vertical electric field to the horizontal
electric field on polarization ellipse at zenith.
Table 7: Summary of GNSS antenna RF interface requirements