User Manual

SARA-R4/N4 series-AT Commands Manual
UBX-17003787 - R11

9Short Messages Service
Page 71 of 308
Parameter Type Description
• 1: if the CBM is stored in the MT, an indication of the used memory location is routed
to DTE using the +CBMI URC
• 2: new CBMs are routed directly to the DTE using the +CBM URC
• 3: class 3 CBMs are routed directly to DTE using URCs defined in <bm>=2. If CBM
storage is supported, messages of other classes result in indication as defined in
<bm>=1
<ds> Number Specifies the rules for managing the Status Report messages:
• 0 (default and factory-programmed value): no SMS-STATUS-REPORTs are routed
to the DTE
• 1: SMS-STATUS-REPORTs are routed to the DTE using the +CDS URC
• 2: if SMS-STATUS-REPORT is stored in the MT, the indication of the memory
location is routed to the DTE using the +CDSI URC
<bfr> Number Controls the buffering of URCs:
• 0 (default and factory-programmed value): MT buffer of URCs defined within this
command is flushed to the DTE when <mode> 1...3 is entered (OK final result code
shall be given before flushing the codes).
• 1: MT buffer of URCs defined within this command is cleared when <mode> 1...3 is
entered
<mem> String Same as defined in +CPMS Defined Values
<index> Number Storage position
<length> Number Two meanings:
• in text mode: number of characters
• in PDU mode: PDU's length in octets without the Service Center's address. In
example: 039121430100038166F6000004E374F80D: this is a PDU with Service
Center's number +1234, that generates the address 03912143 (4 octets). Thus in
this case <length>=13.
<pdu> String Protocol data unit: each 8-bit octet is presented as two IRA character long
hexadecimal numbers, e.g. octet with integer value 42 is presented to TE as two
characters 2A (IRA 50 and 65)
<oa> String Originator address
<scts> String Service center time stamp in time-string format, see the <dt>
<data> String In the case of SMS: 3GPP TS 23.040 [8] TP-User-Data in text mode responses;
format:
• if <dcs> indicates that 3GPP TS 23.038 [7] GSM 7 bit default alphabet is used and
<fo> indicates that 3GPP TS 23.040 [8] TP-User-Data-Header-Indication is not set:
o if TE character set other than "HEX" (see the +CSCS command in 3GPP TS 27.0
07 [2]): ME/TA converts GSM alphabet into current TE character set according
to rules of Annex A
o if TE character set is "HEX": ME/TA converts each 7-bit character of GSM
7 bit default alphabet into two IRA character long hexadecimal number (e.g.
character Æ (GSM 7 bit default alphabet 28) is presented as 1C (IRA 49 and 67))
• if <dcs> indicates that 8-bit or UCS2 data coding scheme is used, or <fo> indicates
that 3GPP TS 23.040 [8] TP-User-Data-Header-Indication is set: ME/TA converts
each 8-bit octet into two IRA character long hexadecimal number (e.g. octet with
integer value 42 is presented to TE as two characters 2A (IRA 50 and 65))
In the case of CBS: 3GPP TS 23.041 [9] CBM Content of Message in text mode
responses; format:
• if <dcs> indicates that 3GPP TS 23.038 [7] GSM 7 bit default alphabet is used:
o if TE character set other than "HEX" (see the +CSCS in 3GPP TS 27.007 [2]): ME/
TA converts GSM alphabet into current TE character set according to rules of
Annex A
o if TE character set is "HEX": ME/TA converts each 7-bit character of the GSM 7
bit default alphabet into two IRA character long hexadecimal number
• if <dcs> indicates that 8-bit or UCS2 data coding scheme is used: ME/TA converts
each 8-bit octet into two IRA character long hexadecimal number
<sn> Number CBM serial number
<mid> Number CBM message identifier
<dcs> Number Data Coding Scheme
<page> Number CBM Page Parameter bits 4-7 in integer format as described in 3GPP TS 23.041 [9]
<pages> Number CBM Page Parameter bits 0-3 in integer format as described in 3GPP TS 23.041 [9]