User Manual

TOBY-L2 and MPCI-L2 series - System Integration Manual
UBX-13004618 - R08 Early Production Information Approvals
Page 143 of 158
4.3.1 Declaration of Conformity
Radiofrequency radiation exposure Information: this equipment complies with radiation
exposure limits prescribed for an uncontrolled environment for fixed and mobile use conditions.
This equipment should be installed and operated with a minimum distance of 20 cm between
the radiator and the body of the user or nearby persons. This transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter except as authorized
in the certification of the product.
The gain of the system antenna(s) used for the TOBY-L200, TOBY-L210, MPCI-L200, MPCI-L210
modules (i.e. the combined transmission line, connector, cable losses and radiating element
gain) must not exceed 9.8 dBi (700 MHz, i.e. LTE FDD-17 band), 4.3 dBi (850 MHz, i.e. GSM 850 or
UMTS FDD-5 or LTE FDD-5 band), 5.5 dBi (1700 MHz, i.e. AWS or UMTS FDD-4 or LTE FDD-4
band), 2.8 dBi (1900 MHz, i.e. GSM 1900 or UMTS FDD-2 or LTE FDD-2 band), 6.0 dBi (2500 MHz,
i.e. LTE FDD-7 band) for mobile and fixed or mobile operating configurations.
The gain of the system antenna(s) used for TOBY-L201 modules (i.e. the combined transmission
line, connector, cable losses and radiating element gain) must not exceed 6.7 dBi (700 MHz, i.e.
LTE FDD-17 band), 6.9 dBi (750 MHz, i.e. LTE FDD-13 band), 6.7 dBi (850 MHz, i.e. UMTS FDD-5 or
LTE FDD-5 band), 6.8 dBi (1700 MHz, i.e. AWS or LTE FDD-4 band), 8.5 dBi (1900 MHz, i.e. UMTS
FDD-2 or LTE FDD-2 band) for mobile and fixed or mobile operating configurations.
.
4.3.2 Modifications
The IC requires the user to be notified that any changes or modifications made to this device that are not
expressly approved by u-blox could void the user's authority to operate the equipment.
Manufacturers of mobile or fixed devices incorporating the TOBY-L2 and MPCI-L2 series
modules are authorized to use the Industry Canada Certificates of the TOBY-L2 series modules
for their own final products according to the conditions referenced in the certificates.
The IC Label shall in the above case be visible from the outside, or the host device shall bear a
second label stating:
"Contains IC: 8595A-TOBYL200" resp.
"Contains IC: 8595A-TOBYL201" resp.
"Contains IC: 8595A-TOBYL210" resp.
"Contains IC: 8595A-TOBYL280" resp.
Canada, Industry Canada (IC) Notices
This Class B digital apparatus complies with Canadian CAN ICES-3(B) / NMB-3(B) and RSS-210.
Operation is subject to the following two conditions:
o this device may not cause interference
o this device must accept any interference, including interference that may cause undesired
operation of the device
Radio Frequency (RF) Exposure Information
The radiated output power of the u-blox Cellular Module is below the Industry Canada (IC)
radio frequency exposure limits. The u-blox Cellular Module should be used in such a manner
such that the potential for human contact during normal operation is minimized.
This device has been evaluated and shown compliant with the IC RF Exposure limits under
mobile exposure conditions (antennas are greater than 20 cm from a person's body).