Integration Manual

TOBY-L2 and MPCI-L2 series - System Integration Manual
UBX-13004618 - R04 Advance Information Design-in
Page 88 of 141
2.5 SIM interface
SIM detection interface (GPIO5) is not available on MPCI-L2 series modules.
SIM detection interface (GPIO5) is not supported by the TOBY-L2x0-00S product version: the pin should
not be driven by any external device.
2.5.1 Guidelines for SIM circuit design
Guidelines for SIM cards, SIM connectors and SIM chips selection
The ISO/IEC 7816, the ETSI TS 102 221 and the ETSI TS 102 671 specifications define the physical, electrical and
functional characteristics of Universal Integrated Circuit Cards (UICC), which contains the Subscriber
Identification Module (SIM) integrated circuit that securely stores all the information needed to identify and
authenticate subscribers over the LTE/3G/2G network.
Removable UICC / SIM card contacts mapping is defined by ISO/IEC 7816 and ETSI TS 102 221 as follows:
 Contact C1 = VCC (Supply)  It must be connected to VSIM or UIM_PWR
 Contact C2 = RST (Reset)  It must be connected to SIM_RST or UIM_RESET
 Contact C3 = CLK (Clock)  It must be connected to SIM_CLK or UIM_CLK
 Contact C4 = AUX1 (Auxiliary contact)  It must be left not connected
 Contact C5 = GND (Ground)  It must be connected to GND
 Contact C6 = VPP (Programming supply)  It must be connected to VSIM or UIM_PWR
 Contact C7 = I/O (Data input/output)  It must be connected to SIM_IO or UIM_DATA
 Contact C8 = AUX2 (Auxiliary contact)  It must be left not connected
A removable SIM card can have 6 contacts (C1, C2, C3, C5, C6, C7) or 8 contacts, also including the auxiliary
contacts C4 and C8 . Only 6 contacts are required and must be connected to the module SIM interface.
Removable SIM cards are suitable for applications requiring a change of SIM card during the product lifetime.
A SIM card holder can have 6 or 8 positions if a mechanical card presence detector is not provided, or it can
have 6+2 or 8+2 positions if two additional pins relative to the normally-open mechanical switch integrated in
the SIM connector for the mechanical card presence detection are provided. Select a SIM connector providing
6+2 or 8+2 positions if the optional SIM detection feature (not available on MPCI-L2 series) is required by the
custom application, otherwise a connector without integrated mechanical presence switch can be selected.
Solderable UICC / SIM chip contact mapping (M2M UICC Form Factor) is defined by ETSI TS 102 671 as:
 Case Pin 8 = UICC Contact C1 = VCC (Supply)  It must be connected to VSIM or UIM_PWR
 Case Pin 7 = UICC Contact C2 = RST (Reset)  It must be connected to SIM_RST or UIM_RESET
 Case Pin 6 = UICC Contact C3 = CLK (Clock)  It must be connected to SIM_CLK or UIM_CLK
 Case Pin 5 = UICC Contact C4 = AUX1 (Aux.contact)  It must be left not connected
 Case Pin 1 = UICC Contact C5 = GND (Ground)  It must be connected to GND
 Case Pin 2 = UICC Contact C6 = VPP (Progr. supply)  It must be connected to VSIM or UIM_PWR
 Case Pin 3 = UICC Contact C7 = I/O (Data I/O)  It must be connected to SIM_IO or UIM_DATA
 Case Pin 4 = UICC Contact C8 = AUX2 (Aux. contact)  It must be left not connected
A solderable SIM chip has 8 contacts and can also include the auxiliary contacts C4 and C8 for other uses, but
only 6 contacts are required and must be connected to the module SIM card interface as described above.
Solderable SIM chips are suitable for M2M applications where it is not required to change the SIM once installed.