Integration Manual

ManualsBrandsu-blox ManualsElectronicsGSM/UMTS/LTE Data Module

TOBY-L2 and MPCI-L2 series

LTE/DC-HSPA+/EGPRS modules

System Integration Manual

Abstract

This document describes the features and the system integration of

TOBY-L2 and MPCI-L2 series multi-mode cellular modules.

These modules are a complete and cost efficient LTE/3G/2G solution

offering up to 150 Mb/s download and 50 Mb/s upload data rates,

covering up to six LTE bands, up to five WCDMA/DC-HSPA+ bands

and four GSM/EGPRS bands in the compact TOBY LGA form factor of

TOBY-L2 modules or in the industry standard PCI Express Mini Card

form factor of MPCI-L2 modules.

TOBY-L2 series

www.u-blox.com

UBX-13004618 - R04

MPCI-L2 series

Summary of content (141 pages)

PAGE 1
TOBY-L2 and MPCI-L2 series LTE/DC-HSPA+/EGPRS modules System Integration Manual Abstract This document describes the features and the system integration of TOBY-L2 and MPCI-L2 series multi-mode cellular modules.
PAGE 2
TOBY-L2 and MPCI-L2 series - System Integration Manual Document Information Title TOBY-L2 and MPCI-L2 series Subtitle LTE/DC-HSPA+/EGPRS modules Document type System Integration Manual Document number UBX-13004618 Revision and date R04 Document status Advance Information 30-Sep-2014 Document status explanation Objective Specification Document contains target values. Revised and supplementary data will be published later. Advance Information Document contains data based on early testing.
PAGE 3
TOBY-L2 and MPCI-L2 series - System Integration Manual Preface u-blox Technical Documentation As part of our commitment to customer support, u-blox maintains an extensive volume of technical documentation for our products. In addition to our product-specific technical data sheets, the following manuals are available to assist u-blox customers in product design and development.  AT Commands Manual: This document provides the description of the AT commands supported by the u-blox cellular modules.
PAGE 4
TOBY-L2 and MPCI-L2 series - System Integration Manual Contents Preface ................................................................................................................................ 3 Contents.............................................................................................................................. 4 1 System description ....................................................................................................... 8 1.1 1.2 Overview .........................
PAGE 5
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.15.3 1.15.4 Jamming detection ...................................................................................................................... 48 IP modes of operation ................................................................................................................. 49 1.15.5 Dual stack IPv4/IPv6 ..................................................................................................................... 49 1.15.6 1.
PAGE 6
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.13 2.14 MPCI-L2 series module installation ................................................................................................ 113 Thermal guidelines ........................................................................................................................ 115 2.15 ESD guidelines .............................................................................................................................. 116 2.15.1 2.
PAGE 7
TOBY-L2 and MPCI-L2 series - System Integration Manual A Glossary .................................................................................................................... 133 B Migration between TOBY-L1 and TOBY-L2 ............................................................ 135 B.1 B.2 Overview .......................................................................................................................................... 135 Pin-out comparison between TOBY-L1 and TOBY-L2 ..........
PAGE 8
TOBY-L2 and MPCI-L2 series - System Integration Manual 1 System description 1.
PAGE 9
TOBY-L2 and MPCI-L2 series - System Integration Manual Table 2 reports a summary of LTE, 3G and 2G cellular radio access technologies characteristics and features of the TOBY-L2 and MPCI-L2 series modules. 4G LTE 3G UMTS/HSDPA/HSUPA 2G GSM/GPRS/EDGE 3GPP Release 9 Long Term Evolution (LTE) Evolved Uni.
PAGE 10
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.2 Architecture Figure 1 summarizes the internal architecture of TOBY-L2 series modules. Duplexer ANT1 Switch Filters Filters LNAs Filters ANT_DET SIM 26 MHz DDC(I2C) PAs Filters LNAs Filters Filters LNAs Filters Filters LNAs Filters Duplexer Filters ANT2 PAs SDIO RF Transceiver UART Memory Cellular Base-band Processor Switch USB GPIO Digital audio (I2S) 32.
PAGE 11
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.2.1 Internal blocks As described in Figure 2, each MPCI-L2 series module integrates one TOBY-L2 series module, which consists of the following internal sections: RF, baseband and power management. RF section The RF section is composed of RF transceiver, PAs, LNAs, crystal oscillator, filters, duplexers and RF switches.
PAGE 12
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.3 Pin-out 1.3.1 TOBY-L2 series pin assignment Table 3 lists the pin-out of the TOBY-L2 series modules, with pins grouped by function. Function Pin Name Pin No I/O Description Remarks Power VCC 70,71,72 I Module supply input VCC pins are internally connected each other. VCC supply circuit affects the RF performance and compliance of the device integrating the module with applicable required certification schemes. See section 1.5.
PAGE 13
TOBY-L2 and MPCI-L2 series - System Integration Manual Function Pin Name Pin No I/O Description Remarks SIM VSIM 59 O SIM supply output VSIM = 1.8 V / 3 V automatically generated according to the connected SIM type. See section 1.8 for functional description. See section 2.5 for external circuit design-in. SIM_IO 57 I/O SIM data Data input/output for 1.8 V / 3 V SIM Internal 4.7 k pull-up to VSIM. See section 1.8 for functional description. See section 2.5 for external circuit design-in.
PAGE 14
TOBY-L2 and MPCI-L2 series - System Integration Manual Function DDC SDIO Pin Name Pin No I/O Description Remarks DSR 10 O/ I/O UART data set ready output / GPIO Note: UART / GPIO not supported by TOBY-L2x0-00S. 1.8 V, Circuit 107 in ITU-T V.24, configurable as GPIO. Add Test-Point and series 0  to access for diagnostic. See section 1.9.2 and 1.11 for functional description. See section 2.6.2 and 2.8 for external circuit design-in.
PAGE 15
TOBY-L2 and MPCI-L2 series - System Integration Manual Function Audio GPIO Reserved Pin Name Pin No I/O Description Remarks SDIO_CMD 65 I/O SDIO command Note: SDIO not supported by TOBY-L2x0-00S. SDIO interface for communication with external Wi-Fi chip See section 1.9.4 for functional description. See section 2.6.4 for external circuit design-in. I2S_TXD 51 O/ I/O I2S transmit data / GPIO Note: I2S and GPIO not supported by TOBY-L2x0-00S.
PAGE 16
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.3.2 MPCI-L2 series pin assignment Table 4 lists the pin-out of the MPCI-L2 series modules, with pins grouped by function. Function Pin Name Pin No I/O Description Remarks Power 3.3Vaux 2, 24, 39, 41, 52 I Module supply input 3.3Vaux pins are internally connected each other. 3.3Vaux supply circuit affects the RF performance and compliance of the device integrating the module with applicable required certification schemes. See section 1.5.
PAGE 17
TOBY-L2 and MPCI-L2 series - System Integration Manual Function Pin Name Pin No I/O Description Remarks USB USB_D- 36 I/O USB Data Line D- USB interface for AT commands, data communication, FOAT, FW update by u-blox EasyFlash tool and diagnostic. 90  nominal differential impedance (Z0) 30  nominal common mode impedance (ZCM) Pull-up or pull-down resistors and external series resistors as required by the USB 2.
PAGE 18
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.4 Operating modes TOBY-L2 and MPCI-L2 series modules have several operating modes. The operating modes are defined in Table 5 and described in detail in Table 6, providing general guidelines for operation. General Status Operating Mode Definition Power-down Not-Powered Mode Power-Off Mode VCC or 3.3Vaux supply not present or below operating range: module is switched off. VCC or 3.3Vaux supply within operating range and module is switched off.
PAGE 19
TOBY-L2 and MPCI-L2 series - System Integration Manual Operating Mode Description Transition between operating modes Connected-Mode RF Tx/Rx data connection is in progress. The module is prepared to accept data signals from an external device unless power saving configuration is enabled by AT+UPSV (see sections 1.9.1.4, 1.9.2.4 and u-blox AT Commands Manual [3]). When a data connection is initiated, the module enters connected-mode from idle-mode.
PAGE 20
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.5 Supply interfaces 1.5.1 Module supply input (VCC or 3.3Vaux) TOBY-L2 modules are supplied via the three VCC pins, and MPCI-L2 modules are supplied via the five 3.3Vaux pins. All supply voltages used inside the modules are generated from the VCC or the 3.3Vaux supply input by integrated voltage regulators, including the V_BCKP RTC supply, the V_INT generic digital interface supply, and the VSIM or UIM_PWR SIM interface supply.
PAGE 21
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.5.1.2 VCC or 3.3Vaux current consumption in 2G connected-mode When a GSM call is established, the VCC or 3.3Vaux module current consumption is determined by the current consumption profile typical of the GSM transmitting and receiving bursts. The peak of current consumption during a transmission slot is strictly dependent on the RF transmitted power, which is regulated by the network.
PAGE 22
TOBY-L2 and MPCI-L2 series - System Integration Manual When a GPRS connection is established, more than one slot can be used to transmit and/or more than one slot can be used to receive. The transmitted power depends on network conditions, which set the peak current consumption, but following the 3GPP specifications the maximum Tx RF power is reduced if more than one slot is used to transmit, so the maximum peak of current is not as high as can be in case of a 2G single-slot call.
PAGE 23
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.5.1.3 VCC or 3.3Vaux current consumption in 3G connected mode During a 3G connection, the module can transmit and receive continuously due to the Frequency Division Duplex (FDD) mode of operation with the Wideband Code Division Multiple Access (WCDMA). The current consumption depends again on output RF power, which is always regulated by network commands.
PAGE 24
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.5.1.4 VCC or 3.3Vaux current consumption in LTE connected-mode During a LTE connection, the module can transmit and receive continuously due to LTE radio access technology. The current consumption is strictly dependent on the transmitted RF output power, which is always regulated by network commands. These power control commands are logically divided into a slot of 0.
PAGE 25
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.5.1.5 VCC or 3.3Vaux current consumption in cyclic idle/active mode (power saving enabled) The power saving configuration is by default disabled, but it can be enabled using the AT+UPSV command (see the u-blox AT Commands Manual [3]). When power saving is enabled, the module automatically enters the low power idle-mode whenever possible, reducing current consumption.
PAGE 26
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.5.1.6 VCC or 3.3Vaux current consumption in fixed active-mode (power saving disabled) When power saving is disabled, the module does not automatically enter the low power idle-mode whenever possible: the module remains in active-mode. Power saving configuration is by default disabled. It can also be disabled using the AT+UPSV command (see u-blox AT Commands Manual [3] for detail usage).
PAGE 27
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.5.2 RTC supply input/output (V_BCKP) The RTC supply V_BCKP pin is not available on MPCI-L2 series modules. The V_BCKP pin of TOBY-L2 series modules connects the supply for the Real Time Clock (RTC). A linear LDO regulator integrated in the Power Management Unit internally generates this supply, as shown in Figure 11, with low current capability (see the TOBY-L2 series Data Sheet [1]).
PAGE 28
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.5.3 Generic digital interfaces supply output (V_INT) The generic digital interfaces supply V_INT pin is not available on MPCI-L2 series modules. The V_INT output pin of the TOBY-L2 series modules is connected to an internal 1.8 V supply with current capability specified in the TOBY-L2 series Data Sheet [1].
PAGE 29
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.6 System function interfaces 1.6.1 Module power-on The PWR_ON input pin is not available on MPCI-L2 series modules. When the TOBY-L2 and MPCI-L2 series modules are in the not-powered mode (switched off, i.e. the VCC or 3.3Vaux module supply is not applied), they can be switched on as following:  Rising edge on the VCC or 3.3Vaux supply input to a valid voltage for module supply, so that the module switches on applying a proper VCC or 3.
PAGE 30
TOBY-L2 and MPCI-L2 series - System Integration Manual Figure 14 shows the module power-on sequence from the not-powered mode, describing the following phases:  The external supply is applied to the VCC or 3.3Vaux module supply inputs, representing the start-up event.  The PWR_ON and the RESET_N or PERST# pins suddenly rise to high logic level due to internal pull-ups.  The V_BCKP RTC supply output is suddenly enabled by the module as VCC reaches a valid voltage value.
PAGE 31
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.6.2 Module power-off TOBY-L2 series can be properly switched off by:  AT+CPWROFF command (see u-blox AT Commands Manual [3]). The current parameter settings are saved in the module’s non-volatile memory and a proper network detach is performed.
PAGE 32
TOBY-L2 and MPCI-L2 series - System Integration Manual Figure 15 describes the TOBY-L2 power-off sequence by means of AT+CPWROFF with the following phases:  When the +CPWROFF AT command is sent, the module starts the switch-off routine.  The module replies OK on the AT interface: the switch-off routine is in progress.
PAGE 33
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.6.3 Module reset TOBY-L2 and MPCI-L2 series modules can be properly reset (rebooted) by:  AT+CFUN command (see u-blox AT Commands Manual [3]). MPCI-L2 series modules can be additionally properly reset (rebooted) by:  AT+CPWROFF command (see u-blox AT Commands Manual [3]): the behavior differs than TOBY-L2 series, as MPCI-L2 modules will reboot rather than remain switched off due to modules’ internal configuration.
PAGE 34
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.7 Antenna interface 1.7.1 Antenna RF interfaces (ANT1 / ANT2) TOBY-L2 and MPCI-L2 series modules provide two RF interfaces for connecting the external antennas:  The ANT1 represents the primary RF input/output for transmission and reception of LTE/3G/2G RF signals.
PAGE 35
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.7.1.1 Antenna RF interfaces requirements Table 8, Table 9 and Table 10 summarize the requirements for the antennas RF interfaces (ANT1 / ANT2). See section 2.4.1 for suggestions to properly design antennas circuits compliant with these requirements. The antenna circuits affect the RF compliance of the device integrating TOBY-L2 and MPCI-L2 series modules with applicable required certification schemes (for more details see section 4).
PAGE 36
TOBY-L2 and MPCI-L2 series - System Integration Manual Item Requirements Remarks Impedance 50  nominal characteristic impedance The impedance of the antenna RF connection must match the 50  impedance of the ANT2 port. Frequency Range See the TOBY-L2 series Data Sheet [1] and the MPCI-L2 series Data Sheet [2] The required frequency range of the antennas connected to ANT2 port depends on the operating bands of the used cellular module and the used Mobile Network.
PAGE 37
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.7.2 Antenna detection interface (ANT_DET) Antenna detection interface (ANT_DET) is not available on MPCI-L2 series modules. Antenna detection interface (ANT_DET) is not supported by the TOBY-L2x0-00S product version. The antenna detection is based on ADC measurement. The ANT_DET pin is an Analog to Digital Converter (ADC) provided to sense the antenna presence.
PAGE 38
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.9 Data communication interfaces TOBY-L2 and MPCI-L2 series modules provide the following serial communication interface:  USB interface: High-Speed USB 2.0 compliant interface available for the communication with an external host application processor, for AT commands, data communication, FW upgrade by means of the FOAT feature, FW upgrade by means of the u-blox EasyFlash tool and for diagnostic purpose (see section 1.9.
PAGE 39
TOBY-L2 and MPCI-L2 series - System Integration Manual TOBY-L2 and MPCI-L2 modules provide by default the following USB profile with the listed set of USB functions:  1 RNDIS for Ethernet-over-USB connection  1 CDC-ACM for AT commands and data communication The USB profile of TOBY-L2 and MPCI-L2 modules identifies itself by its VID (Vendor ID) and PID (Product ID) combination, included in the USB device descriptor according to the USB 2.0 specifications [6].
PAGE 40
TOBY-L2 and MPCI-L2 series - System Integration Manual For example, the default USB profile configuration which provides 2 functions (1 RNDIS for Ethernet-over-USB and 1 CDC-ACM for AT commands and data) can be changed by means of the AT+UUSBCONF command switching to a USB profile configuration which provides the following 6 functions:  3 CDC-ACM for AT commands and data  1 CDC-ACM for GNSS tunneling  1 CDC-ACM for SIM Access Profile (SAP)  1 CDC-ACM for diagnostic As each USB profile of TOBY-L
PAGE 41
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.9.1.2 USB in Windows The USB drivers (INF files) are provided for Windows systems and should be installed properly by following the step-by-step instruction in EVK-L20 / EVK-L21 User Guide [4]. USB drivers are available for the following operating system platforms:  Windows Vista  Windows 7  Windows 8  Windows 8.
PAGE 42
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.9.2 Asynchronous serial interface (UART) The UART interface is not available on MPCI-L2 series modules. The UART interface is not supported by the TOBY-L2x0-00S product version. 1.9.2.1 UART features The UART interface is a 9-wire 1.8 V unbalanced asynchronous serial interface (UART) that can be connected to an application host processor for AT commands and data communication.
PAGE 43
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.9.2.3 UART signals behavior At the module switch-on, before the UART interface initialization (as described in the power-on sequence reported in Figure 14), each pin is first tri-stated and then is set to its relative internal reset state. At the end of the boot sequence, the UART interface is initialized, the module is by default in active-mode, and the UART interface is enabled. 1.9.2.
PAGE 44
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.9.3 DDC (I2C) interface 2 The I C bus compatible Display Data Channel interface is not available on the MPCI-L2 series modules, as ® AssistNow embedded GNSS positioning aiding, CellLocate positioning through cellular information and custom functions over GPIOs for the integration with u-blox positioning chips / modules.
PAGE 45
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.9.4 Secure Digital Input Output interface (SDIO) Secure Digital Input Output interface is not available on MPCI-L2 series modules. Secure Digital Input Output interface is not supported by the TOBY-L2x0-00S product version. TOBY-L2 series modules include a 4-bit Secure Digital Input Output interface (SDIO_D0, SDIO_D1, SDIO_D2, SDIO_D3, SDIO_CLK, SDIO_CMD) designed to communicate with an external Wi-Fi chip. 1.10 Audio 1.10.
PAGE 46
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.11 General Purpose Input/Output General Purpose Input / Output pins are not supported by the TOBY-L2x0-00S product version except for the Wireless Wide Area Network status indication configured on the GPIO1 pin. General Purpose Input / Output pins are not available on MPCI-L2 series modules.
PAGE 47
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.12 Mini PCIe specific signals (W_DISABLE#, LED_WWAN#) Mini PCI Express specific signals (W_DISABLE#, LED_WWAN#) are not available on TOBY-L2 series. MPCI-L2 series modules include the W_DISABLE# active-low input signal to disable the radio operations as specified by the PCI Express Mini Card Electromechanical Specification [14]. As described in Figure 20, the W_DISABLE# input is equipped with an internal pull-up to the 3.3Vaux supply.
PAGE 48
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.15 System features 1.15.1 Network indication Network status indication over GPIO1 is not available on MPCI-L2 series modules which include the LED_WWAN# active-low open drain output to provide the Wireless Wide Area Network status indication as specified by the PCI Express Mini Card Electromechanical Specification [14].
PAGE 49
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.15.4 IP modes of operation IP modes of operation refer to the TOBY-L2 and MPCI-L2 series modules configuration related to the network IP termination and network interfaces settings in general. IP modes of operation are the following:  Bridge mode: In bridge mode the module acts as a cellular modem dongle connected to the host over serial interface (USB). The IP termination of the network is placed on the host IP stack.
PAGE 50
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.15.8 HTTP and HTTPS Embedded HTTP and HTTPS services are not supported by TOBY-L2x0-00S and MPCI-L2x0-00S. TOBY-L2 and MPCI-L2 series modules provide the embedded Hyper-Text Transfer Protocol (HTTP) and the Secure Hyper-Text Transfer Protocol (HTTPS, i.e.
PAGE 51
TOBY-L2 and MPCI-L2 series - System Integration Manual ® Positioning through cellular information: CellLocate ® u-blox CellLocate enables the estimation of device position based on the parameters of the mobile network cells ® visible to the specific device. To estimate its position the u-blox cellular module sends the CellLocate server the parameters of network cells visible to it using a UDP connection. In return the server provides the estimated ® position based on the CellLocate database.
PAGE 52
TOBY-L2 and MPCI-L2 series - System Integration Manual ® 3. If a new device reports the observation of Cell A CellLocate is able to provide the estimated position from the area of visibility 4. The visibility of multiple cells provides increased accuracy based on the intersection of areas of visibility. ® ® CellLocate is implemented using a set of two AT commands that allow configuration of the CellLocate service (AT+ULOCCELL) and requesting position according to the user configuration (AT+ULOC).
PAGE 53
TOBY-L2 and MPCI-L2 series - System Integration Manual 2 The use of hybrid positioning requires a connection via the DDC (I C) bus between the TOBY-L2 series cellular module and the u-blox GNSS receiver (see sections 1.9.3 and 2.6.3). See GNSS Implementation Application Note [13] for the complete description of the feature. ® u-blox is extremely mindful of user privacy. When a position is sent to the CellLocate server u-blox is unable to track the SIM used or the specific device. 1.15.
PAGE 54
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.15.14 In-band Modem (eCall / ERA-GLONASS) In-band modem for eCall / ERA-GLONASS emergency applications is not supported by TOBY-L2x0-00S and MPCI-L2 series. In-band Modem solution for eCall and ERA-GLONASS emergency call applications over cellular networks is implemented according to 3GPP TS 26.267 [15], BS EN 16062:2011 [16] and ETSI TS 122 101 [17] specifications.
PAGE 55
TOBY-L2 and MPCI-L2 series - System Integration Manual TOBY-L2 series modules, acting as an SAP client, can be connected to an SAP server by a completely wired connection, as shown in Figure 22.
PAGE 56
TOBY-L2 and MPCI-L2 series - System Integration Manual 1.15.16 Smart temperature management Smart temperature management is not supported by TOBY-L2x0-00S and MPCI-L2x0-00S. Cellular modules – independent of the specific model – always have a well defined operating temperature range. This range should be respected to guarantee full device functionality and long life span. Nevertheless there are environmental conditions that can affect operating temperature, e.g.
PAGE 57
TOBY-L2 and MPCI-L2 series - System Integration Manual Figure 25 shows the flow diagram implemented for the Smart Temperature Supervisor.
PAGE 58
TOBY-L2 and MPCI-L2 series - System Integration Manual Threshold Definitions When the application of cellular module operates at extreme temperatures with Smart Temperature Supervisor enabled, the user should note that outside the valid temperature range the device will automatically shut down as described above. The input for the algorithm is always the temperature measured within the cellular module (Ti, internal).
PAGE 59
TOBY-L2 and MPCI-L2 series - System Integration Manual 2 Design-in 2.1 Overview For an optimal integration of TOBY-L2 and MPCI-L2 series modules in the final application board follow the design guidelines stated in this section. Every application circuit must be properly designed to guarantee the correct functionality of the relative interface, however a number of points require high attention during the design of the application device.
PAGE 60
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.2 Supply interfaces 2.2.1 Module supply (VCC or 3.3Vaux) 2.2.1.1 General guidelines for VCC or 3.3Vaux supply circuit selection and design VCC or 3.3Vaux pins are internally connected. Application design shall connect all the available pads to the external supply to minimize the power loss due to series resistance. GND pins are internally connected.
PAGE 61
TOBY-L2 and MPCI-L2 series - System Integration Manual charger is the typical choice when the charging source has an high nominal voltage (e.g. ~12 V), whereas a linear charger is the typical choice when the charging source has a relatively low nominal voltage (~5 V). If both a permanent primary supply / charging source (e.g. ~12 V) and a rechargeable back-up battery (e.g. 3.
PAGE 62
TOBY-L2 and MPCI-L2 series - System Integration Manual Figure 27 and Table 13 show an example of a high reliability power supply circuit, where the module VCC or 3.3Vaux input is supplied by a step-down switching regulator capable of delivering maximum current with low output ripple and with fixed switching frequency in PWM mode operation greater than 1 MHz.
PAGE 63
TOBY-L2 and MPCI-L2 series - System Integration Manual Figure 28 and the components listed in Table 14 show an example of a low cost power supply circuit, where the VCC module supply is provided by a step-down switching regulator capable of delivering to VCC pins the specified maximum peak / pulse current, transforming a 12 V supply input.
PAGE 64
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.2.1.3 Guidelines for VCC or 3.3Vaux supply circuit design using a Low Drop-Out linear regulator The use of a linear regulator is suggested when the difference from the available supply rail and the VCC or the 3.3Vaux value is low. The linear regulators provide high efficiency when transforming a 5 VDC supply to a voltage value within the module VCC or 3.3Vaux normal operating range.
PAGE 65
TOBY-L2 and MPCI-L2 series - System Integration Manual Figure 30 and the components listed in Table 16 show an example of a low cost power supply circuit, where the VCC module supply is provided by an LDO linear regulator capable of delivering the specified highest peak / pulse current, with proper power handling capability. The regulator described in this example supports a limited input voltage range and it includes internal circuitry for current and thermal protection.
PAGE 66
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.2.1.
PAGE 67
TOBY-L2 and MPCI-L2 series - System Integration Manual TOBY-L2 series 3V8 VCC 70 VCC 71 VCC 72 C1 C2 C3 C4 C5 C6 GND MPCI-L2 series 3V3 3.3Vaux 3.3Vaux 3.3Vaux 3.3Vaux 3.3Vaux 2 24 39 41 52 C1 C2 C3 C4 C5 C6 GND Figure 31: Suggested schematic for the VCC / 3.
PAGE 68
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.2.1.7 Guidelines for external battery charging circuit TOBY-L2 modules do not have an on-board charging circuit. Figure 32 provides an example of a battery charger design, suitable for applications that are battery powered with a Li-Ion (or Li-Polymer) cell.
PAGE 69
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.2.1.8 Guidelines for external battery charging and power path management circuit Application devices where both a permanent primary supply / charging source (e.g. ~12 V) and a rechargeable back-up battery (e.g. 3.
PAGE 70
TOBY-L2 and MPCI-L2 series - System Integration Manual Battery charging is managed in three phases:  Pre-charge constant current (active when the battery is deeply discharged): the battery is charged with a low current, set to 10% of the fast-charge current  Fast-charge constant current: the battery is charged with the maximum current, configured by the value of an external resistor to a value suitable for the application  Constant voltage: when the battery voltage reaches the regulated output volt
PAGE 71
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.2.1.9 Guidelines for VCC or 3.3Vaux supply layout design Good connection of the module VCC or 3.3Vaux pins with DC supply source is required for correct RF performance. Guidelines are summarized in the following list:  All the available VCC / 3.3Vaux pins must be connected to the DC source  VCC / 3.
PAGE 72
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.2.2 RTC supply output (V_BCKP) The RTC supply V_BCKP pin is not available on MPCI-L2 series modules. 2.2.2.
PAGE 73
TOBY-L2 and MPCI-L2 series - System Integration Manual If the RTC timing is not required when the VCC supply is removed, it is not needed to connect the V_BCKP pin to an external capacitor or battery. In this case the date and time are not updated when VCC is disconnected. If VCC is always supplied, then the internal regulator is supplied from the main supply and there is no need for an external component on V_BCKP.
PAGE 74
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.2.3 Generic digital interfaces supply output (V_INT) The generic digital interfaces supply V_INT pin is not available on MPCI-L2 series modules. 2.2.3.1 Guidelines for V_INT circuit design TOBY-L2 series provide the V_INT generic digital interfaces 1.8 V supply output, which can be mainly used to:  Indicate when the module is switched on (as described in sections 1.6.1, 1.6.2)  Pull-up SIM detection signal (see section 2.
PAGE 75
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.3 System functions interfaces 2.3.1 Module power-on (PWR_ON) The PWR_ON input pin is not available on MPCI-L2 series modules. 2.3.1.1 Guidelines for PWR_ON circuit design TOBY-L2 series PWR_ON input is equipped with an internal active pull-up resistor to the VCC module supply as described in Figure 36: an external pull-up resistor is not required and should not be provided.
PAGE 76
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.3.2 Module reset (RESET_N or PERST#) 2.3.2.1 Guidelines for RESET_N and PERST# circuit design The TOBY-L2 series RESET_N is equipped with an internal pull-up to the VCC supply and the MPCI-L2 series PERST# is equipped with an internal pull-up to the 3.3 V rail, as described in Figure 37. An external pull-up resistor is not required and should not be provided.
PAGE 77
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.3.2.2 Guidelines for RESET_N and PERST# layout design The RESET_N and PERST# circuits require careful layout due to the pin function: ensure that the voltage level is well defined during operation and no transient noise is coupled on this line, otherwise the module might detect a spurious reset request. It is recommended to keep the connection line to RESET_N and PERST# pins as short as possible. 2.3.
PAGE 78
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.4 Antenna interface TOBY-L2 and MPCI-L2 series modules provide two RF interfaces for connecting the external antennas:  The ANT1 pin represents the primary RF input/output for LTE/3G/2G RF signals transmission and reception.  The ANT2 pin represents the secondary RF input for LTE MIMO 2 x 2 or 3G Rx diversity RF signals reception.
PAGE 79
TOBY-L2 and MPCI-L2 series - System Integration Manual o Radiation performance depends on the whole PCB and antenna system design, including product mechanical design and usage. Antennas should be selected with optimal radiating performance in the operating bands according to the mechanical specifications of the PCB and the whole product. o It is recommended to select a pair of custom antennas designed by an antennas’ manufacturer if the required ground plane dimensions are very small (e.g. less than 6.
PAGE 80
TOBY-L2 and MPCI-L2 series - System Integration Manual Guidelines for MPCI-L2 series ANT1 / ANT2 receptacles RF connection design The Hirose U.FL-R-SMT RF receptacles implemented on the MPCI-L2 series modules for ANT1 / ANT2 ports require a suitable mated RF plug from the same connector series. Due to its wide usage in the industry, several manufacturers offer compatible equivalents.
PAGE 81
TOBY-L2 and MPCI-L2 series - System Integration Manual Guidelines for RF transmission line design Any RF transmission line, such as the ones from the ANT1 and ANT2 pads up to the related antenna connector or up to the related internal antenna pad, must be designed so that the characteristic impedance is as close as possible to 50 .
PAGE 82
TOBY-L2 and MPCI-L2 series - System Integration Manual  the gap from the transmission line to the adjacent ground plane on the same layer of the transmission line (e.g. 500 µm in Figure 40, 400 µm in Figure 41) If the distance between the transmission line and the adjacent GND area (on the same layer) does not exceed 5 times the track width of the micro strip, use the “Coplanar Waveguide” model for the 50  calculation.
PAGE 83
TOBY-L2 and MPCI-L2 series - System Integration Manual Guidelines for RF termination design RF terminations must provide a characteristic impedance of 50  as well as the RF transmission lines up to the RF terminations themselves, to match the characteristic impedance of the ANT1 / ANT2 ports of the modules. However, real antennas do not have perfect 50  load on all the supported frequency bands.
PAGE 84
TOBY-L2 and MPCI-L2 series - System Integration Manual Examples of antennas Table 24 lists some examples of possible internal on-board surface-mount antennas. Manufacturer Part Number Product Name Description Taoglas PCS.06.A Havok GSM / WCDMA / LTE SMD Antenna 698..960 MHz, 1710..2170 MHz, 2500..2690 MHz 42.0 x 10.0 x 3.0 mm 700..960 MHz, 1710..2170 MHz Taoglas PA.710.A Warrior GSM / WCDMA / LTE SMD Antenna 698..960 MHz, 1710..2170 MHz, 2300..2400 MHz, 2490..2690 MHz 40.0 x 6.0 x 5.
PAGE 85
TOBY-L2 and MPCI-L2 series - System Integration Manual Table 26 lists some examples of possible external antennas. Manufacturer Part Number Product Name Description Taoglas GSA.8827.A.101111 Phoenix Taoglas TG.30.8112 Laird Tech. TRA6927M3PW-001 Laird Tech. CMS69273 GSM / WCDMA / LTE adhesive-mount Antenna with cable and SMA(M) 698..960 MHz, 1575.42 MHz, 1710..2170 MHz, 2490..2690 MHz 105 x 30 x 7.7 mm GSM / WCDMA / LTE swivel dipole Antenna with SMA(M) 698..960 MHz, 1575.42 MHz, 1710..
PAGE 86
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.4.2 Antenna detection interface (ANT_DET) Antenna detection interface (ANT_DET) is not available on MPCI-L2 series modules. Antenna detection interface (ANT_DET) is not supported by the TOBY-L2x0-00S product version. 2.4.2.
PAGE 87
TOBY-L2 and MPCI-L2 series - System Integration Manual The DC impedance at RF port for some antennas may be a DC open (e.g. linear monopole) or a DC short to reference GND (e.g. PIFA antenna).
PAGE 88
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.5 SIM interface SIM detection interface (GPIO5) is not available on MPCI-L2 series modules. SIM detection interface (GPIO5) is not supported by the TOBY-L2x0-00S product version: the pin should not be driven by any external device. 2.5.
PAGE 89
TOBY-L2 and MPCI-L2 series - System Integration Manual Guidelines for single SIM card connection without detection A removable SIM card placed in a SIM card holder must be connected to the SIM card interface of TOBY-L2 and MPCI-L2 series modules as described in Figure 44, where the optional SIM detection feature is not implemented.
PAGE 90
TOBY-L2 and MPCI-L2 series - System Integration Manual Guidelines for single SIM chip connection A solderable SIM chip (M2M UICC Form Factor) must be connected the SIM card interface of TOBY-L2 and MPCI-L2 series modules as described in Figure 45. Follow these guidelines to connect the module to a solderable SIM chip without SIM presence detection:  Connect the UICC / SIM contacts C1 (VCC) and C6 (VPP) to the VSIM / UIM_PWR pin of the module.
PAGE 91
TOBY-L2 and MPCI-L2 series - System Integration Manual Guidelines for single SIM card connection with detection A removable SIM card placed in a SIM card holder must be connected to the SIM card interface of TOBY-L2 modules as described in Figure 46, where the optional SIM card detection feature is implemented. Follow these guidelines to connect the module to a SIM connector implementing SIM presence detection:  Connect the UICC / SIM contacts C1 (VCC) and C6 (VPP) to the VSIM pin of the module.
PAGE 92
TOBY-L2 and MPCI-L2 series - System Integration Manual Guidelines for dual SIM card / chip connection Two SIM card / chip can be connected to the SIM interface of TOBY-L2 and MPCI-L2 series modules as described in the application circuits of Figure 47.
PAGE 93
TOBY-L2 and MPCI-L2 series - System Integration Manual FIRST SIM CARD TOBY-L2 series VPP (C6) 3V8 4PDT Analog Switch VCC (C1) C11 IO (C7) VCC VSIM 59 SIM_IO 57 SIM_CLK 56 SIM_RST 58 VSIM 1VSIM 2VSIM DAT 1DAT 2DAT CLK 1CLK 2CLK RST 1RST 2RST CLK (C3) RST (C2) C1 C2 C3 C4 GND (C5) C5 D1 D2 D3 D4 J1 SECOND SIM CARD VPP (C6) SEL GND VCC (C1) U1 IO (C7) CLK (C3) Application Processor RST (C2) GPIO C6 R1 C7 C8 C9 C10 GND (C5) D5 D6 D7 D8 J2 FIRST SIM CARD MPCI-L2 series VPP (
PAGE 94
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.5.2 Guidelines for SIM layout design The layout of the SIM card interface lines (VSIM, SIM_CLK, SIM_IO, SIM_RST or UIM_PWR, UIM_DATA, UIM_CLK, UIM_RESET) may be critical if the SIM card is placed far away from the TOBY-L2 and MPCI-L2 series modules or in close proximity to the RF antenna: these two cases should be avoided or at least mitigated as described below.
PAGE 95
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.6 Data communication interfaces 2.6.1 Universal Serial Bus (USB) 2.6.1.1 Guidelines for USB circuit design The USB_D+ and USB_D- lines carry the USB serial data and signaling. The lines are used in single ended mode for full speed signaling handshake, as well as in differential mode for high speed signaling and data transfer. USB pull-up or pull-down resistors and external series resistors on USB_D+ and USB_D- lines as required by the USB 2.
PAGE 96
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.6.1.2 Guidelines for USB layout design The USB_D+ / USB_D- lines require accurate layout design to achieve reliable signaling at the high speed data rate (up to 480 Mb/s) supported by the USB serial interface. The characteristic impedance of the USB_D+ / USB_D- lines is specified by the Universal Serial Bus Revision 2.0 specification [6].
PAGE 97
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.6.2 Asynchronous serial interface (UART) The UART interface is not available on MPCI-L2 series modules. 2.6.2.1 Guidelines for UART circuit design The UART is not supported by TOBY-L2x0-00S: the pins should be not driven by any external device. Providing the full RS-232 functionality (using the complete V.
PAGE 98
TOBY-L2 and MPCI-L2 series - System Integration Manual Providing the TXD, RXD, RTS and CTS lines only (not using the complete V.
PAGE 99
TOBY-L2 and MPCI-L2 series - System Integration Manual Providing the TXD and RXD lines only (not using the complete V24 link) If the functionality of the CTS, RTS, DSR, DCD, RI and DTR lines is not required in the application, or the lines are not available, the circuit with a 1.
PAGE 100
TOBY-L2 and MPCI-L2 series - System Integration Manual Additional considerations Do not apply voltage to any UART interface pin before the switch-on of the UART supply source (V_INT), to avoid latch-up of circuits and allow a proper boot of the module. If the external signals connected to the cellular module cannot be tri-stated or set low, insert a multi channel digital switch (e.g.
PAGE 101
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.6.3 DDC (I2C) interface 2 The I C bus compatible Display Data Channel interface is not available on MPCI-L2 series modules. 2 2.6.3.1 Guidelines for DDC (I C) circuit design 2 I C bus function is not supported by TOBY-L2x0-00S: the pins should be not driven by any external device. General considerations 2 The DDC I C-bus master interface can be used to communicate with u-blox GNSS receivers and other external 2 I C-bus slaves as an audio codec.
PAGE 102
TOBY-L2 and MPCI-L2 series - System Integration Manual Connection with u-blox 1.8 V GNSS receivers Figure 57 shows an application circuit for connecting TOBY-L2 cellular modules to a u-blox 1.8 V GNSS receiver.  SDA / SCL pins of the TOBY-L2 cellular module are directly connected to the relative I C pins of the u-blox 1.8 V GNSS receiver, with appropriate pull-up resistors connected to the 1.8 V GNSS supply enabled after 2 the V_INT supply of the I C pins of the TOBY-L2 cellular module.
PAGE 103
TOBY-L2 and MPCI-L2 series - System Integration Manual According to the V_INT supply output voltage ripple characteristic specified in the TOBY-L2 Data Sheet [1]:  Additional filtering may be needed to properly supply an external LNA, depending on the characteristics of the used LNA, adding a series ferrite bead and a bypass capacitor (e.g. the Murata BLM15HD182SN1 ferrite bead and the Murata GRM1555C1H220J 22 pF capacitor) at the input of the external LNA supply line u-blox GNSS 1.
PAGE 104
TOBY-L2 and MPCI-L2 series - System Integration Manual Connection with u-blox 3.0 V GNSS receivers Figure 59 shows an application circuit for connecting TOBY-L2 cellular modules to a u-blox 3.0 V GNSS receiver:  As the SDA and SCL pins of the TOBY-L2 cellular module are not tolerant up to 3.0 V, the connection to the 2 2 related I C pins of the u-blox 3.0 V GNSS receiver must be provided using a proper I C-bus Bidirectional Voltage Translator with proper pull-up resistors (e.g.
PAGE 105
TOBY-L2 and MPCI-L2 series - System Integration Manual 2 2.6.3.2 Guidelines for DDC (I C) layout design 2 The DDC (I C) serial interface requires the same consideration regarding electro-magnetic interference as any other digital interface. Keep the traces short and avoid coupling with RF line or sensitive analog inputs, since the signals can cause the radiation of some harmonics of the digital data frequency. 2.6.
PAGE 106
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.7 Audio interface 2.7.1 Digital audio interface 2 The I S interface is not available on MPCI-L2 series modules. 2.7.1.1 Guidelines for digital audio circuit design 2 The I S interface is not supported by TOBY-L2x0-00S: the pins should be not driven by any external device. 2 I S digital audio interface can be connected to an external digital audio device for voice applications.
PAGE 107
TOBY-L2 and MPCI-L2 series - System Integration Manual TOBY-L2 series (except TOBY-L2x0-00S) V_INT 1V8 5 R1 R2 R3 Audio Codec C1 IRQn SDA 55 C3 MICBIAS C4 SDA SCL 54 C2 VDD SCL I2S_TXD 51 SDIN I2S_RXD 53 SDOUT I2S_CLK 52 BCLK I2S_WA 50 LRCLK GPIO6 61 MCLK MICLP MICLN EMI1 C5 OUTP EMI2 C6 J1 R5 MICGND OUTN Microphone Connector MIC R4 C12 C11 C8 C7 D1 EMI3 Speaker SPK Connector EMI4 J2 GND GND C14 C13 C10 C9 D2 U1 Figure 60: I2S interface application circuit wi
PAGE 108
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.8 General Purpose Input/Output GPIOs are not supported by the TOBY-L2x0-00S product version except for the Wireless Wide Area Network status indication configured on the GPIO1 pin: the pins should be not driven by any external device. GPIOs are not available on MPCI-L2 series modules. 2.8.1.
PAGE 109
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.9 Mini PCIe specific signals (W_DISABLE#, LED_WWAN#) Mini PCI Express specific signals (W_DISABLE#, LED_WWAN#) are not available on TOBY-L2 series. 2.9.1.1 Guidelines for W_DISABLE# circuit design As described in Figure 62, the MPCI-L2 series modules W_DISABLE# wireless disable input is equipped with an internal pull-up to the 3.3Vaux supply: an external pull-up resistor is not required and should not be provided.
PAGE 110
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.9.1.2 Guidelines for LED_WWAN# circuit design As described in Figure 63 and Table 42, the MPCI-L2 series modules LED_WWAN# active-low open drain output can be directly connected to a system-mounted LED to provide the Wireless Wide Area Network status indication as specified by the PCI Express Mini Card Electromechanical Specification [14].
PAGE 111
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.11 Module placement An optimized placement allows a minimum RF line’s length and closer path from DC source for VCC / 3.3Vaux. Make sure that the module, analog parts and RF circuits are clearly separated from any possible source of radiated energy. In particular, digital circuits can radiate digital frequency harmonics, which can produce ElectroMagnetic Interference that affects the module, analog parts and RF circuits’ performance.
PAGE 112
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.12 TOBY-L2 series module footprint and paste mask Figure 65 and Table 43 describe the suggested footprint (i.e. copper mask) layout for TOBY-L2 series modules. The proposed land pattern layout slightly reflects the modules’ pads layout, with most of the lateral pads designed wider on the application board (1.8 x 0.8 mm) than on the module (1.5 x 0.8 mm).
PAGE 113
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.13 MPCI-L2 series module installation MPCI-L2 series modules are fully compliant with the 52-pin PCI Express Full-Mini Card Type F2 form factor, i.e., top-side and bottom-side keep-out areas, 50.95 mm nominal length, 30 mm nominal width, and all the other dimensions as defined by the PCI Express Mini Card Electromechanical Specification [14], except for the card thickness (which nominal value is 3.7 mm), as described in Figure 66.
PAGE 114
TOBY-L2 and MPCI-L2 series - System Integration Manual MPCI-L2 series modules are equipped with two Hirose U.FL-R-SMT RF receptacles for ANT1 / ANT2 ports, which require a suitable mated RF plug from the same connector series as the examples listed in Table 23. To mate the connectors, the mating axes of both connectors must be aligned. The "click" will confirm the fully mated connection.
PAGE 115
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.14 Thermal guidelines Modules’ operating temperature range is specified in TOBY-L2 Data Sheet [1] and MPCI-L2 Data Sheet [2]. The most critical condition concerning module thermal performance is the uplink transmission at maximum power (data upload in connected-mode), when the baseband processor runs at full speed, radio circuits are all active and the RF power amplifier is driven to higher output RF power.
PAGE 116
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.15 ESD guidelines The sections 2.15.1 and 2.15.2 are related to EMC / ESD immunity. The modules are ESD sensitive devices. The ESD sensitivity for each pin (as Human Body Model according to JESD22-A114F) is specified in TOBY-L2 series Data Sheet [1] or MPCI-L2 series Data Sheet [2]. Special precautions are required when handling the pins; for ESD handling guidelines see section 3.2. 2.15.
PAGE 117
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.15.2 ESD immunity test of TOBY-L2 and MPCI-L2 series reference designs Although EMC / ESD certification is required for customized devices integrating TOBY-L2 and MPCI-L2 series modules for R&TTED and European Conformance CE mark, EMC certification (including ESD immunity) has been successfully performed on TOBY-L2 and MPCI-L2 series modules reference design according to European Norms summarized in Table 45.
PAGE 118
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.16 Schematic for TOBY-L2 and MPCI-L2 series module integration Figure 69 is an example of a schematic diagram where a TOBY-L2x0-00S module is integrated into an application board, using all the available interfaces and functions of the module. TOBY-L2x0-00S Primary Antenna 3V8 + 330uF 100nF 10nF 68pF 15pF 70 VCC 71 VCC 72 VCC 8.
PAGE 119
TOBY-L2 and MPCI-L2 series - System Integration Manual Figure 70 is an example of a schematic diagram where a MPCI-L2 series module is integrated into an application board, using all the available interfaces and functions of the module. MPCI-L2 series 3V3 + 330uF 100nF 10nF 68pF 15pF 2 3.3Vaux 24 3.3Vaux 39 3.3Vaux 41 3.3Vaux 52 3.3Vaux 8.2pF GND Application Processor 22 PERST # D- 27 USB_D- D+ 28 USB_D+ Open Drain Output USB 2.
PAGE 120
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.17 Design-in checklist This section provides a design-in checklist. 2.17.1 Schematic checklist The following are the most important points for a simple schematic check:   DC supply must provide a nominal voltage at VCC / 3.3Vaux pin within the operating range limits.  VCC / 3.
PAGE 121
TOBY-L2 and MPCI-L2 series - System Integration Manual 2.17.2 Layout checklist The following are the most important points for a simple layout check:  Check 50  nominal characteristic impedance of the RF transmission line connected to the ANT1 and the ANT2 ports (antenna RF interfaces).  Ensure no coupling occurs between the RF interface and noisy or sensitive signals (primarily USB signals, digital input/output signals, SIM signals, high-speed digital lines such as address and data lines).
PAGE 122
TOBY-L2 and MPCI-L2 series - System Integration Manual 3 Handling and soldering No natural rubbers, no hygroscopic materials or materials containing asbestos are employed. 3.
PAGE 123
TOBY-L2 and MPCI-L2 series - System Integration Manual 3.3 Soldering 3.3.1 Soldering paste "No Clean" soldering paste is strongly recommended for TOBY-L2 series modules, as it does not require cleaning after the soldering process has taken place. The paste listed in the example below meets these criteria. Soldering Paste: OM338 SAC405 / Nr.143714 (Cookson Electronics) Alloy specification: 95.5% Sn / 3.9% Ag / 0.6% Cu (95.5% Tin / 3.9% Silver / 0.6% Copper) 95.5% Sn / 4.0% Ag / 0.5% Cu (95.5% Tin / 4.
PAGE 124
TOBY-L2 and MPCI-L2 series - System Integration Manual To avoid falling off, modules should be placed on the topside of the motherboard during soldering. The soldering temperature profile chosen at the factory depends on additional external factors like choice of soldering paste, size, thickness and properties of the base board, etc. Exceeding the maximum soldering temperature and the maximum liquidus time limit in the recommended soldering profile may permanently damage the module.
PAGE 125
TOBY-L2 and MPCI-L2 series - System Integration Manual 3.3.5 Repeated reflow soldering Only a single reflow soldering process is encouraged for boards with a module populated on it. 3.3.6 Wave soldering Boards with combined through-hole technology (THT) components and surface-mount technology (SMT) devices require wave soldering to solder the THT components. Only a single wave soldering process is encouraged for boards populated with the modules. 3.3.7 Hand soldering Hand soldering is not recommended.
PAGE 126
TOBY-L2 and MPCI-L2 series - System Integration Manual 4 Approvals For the complete list of all the certification schemes approvals of TOBY-L2 and MPCI-L2 series modules and the corresponding declarations of conformity, see the u-blox web-site (http://www.u-blox.com/). 4.
PAGE 127
TOBY-L2 and MPCI-L2 series - System Integration Manual 4.2 Federal Communications Commission and Industry Canada notice Federal Communications Commission (FCC) IDs:  XPYTOBYL200  XPYTOBYL210 Industry Canada (IC) Certification Numbers:  8595A-TOBYL200  8595A-TOBYL210 4.2.1 Safety warnings review the structure  Equipment for building-in.
PAGE 128
TOBY-L2 and MPCI-L2 series - System Integration Manual The FCC Label shall in the above case be visible from the outside, or the host device shall bear a second label stating: "Contains FCC ID: XPYTOBYL200" resp. "Contains FCC ID: XPYTOBYL210" resp. The IC Label shall in the above case be visible from the outside, or the host device shall bear a second label stating: "Contains IC: 8595A-TOBYL200" resp. "Contains IC: 8595A-TOBYL210" resp.
PAGE 129
TOBY-L2 and MPCI-L2 series - System Integration Manual Ce périphérique est homologué pour l'utilisation au Canada. Pour consulter l'entrée correspondant à l’appareil dans la liste d'équipement radio (REL - Radio Equipment List) d'Industrie Canada rendez-vous sur: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=fra Pour des informations supplémentaires concernant l'exposition aux RF au Canada rendez-vous sur: http://www.ic.gc.ca/eic/site/smt-gst.nsf/fra/sf08792.
PAGE 130
TOBY-L2 and MPCI-L2 series - System Integration Manual 5 Product testing 5.1 u-blox in-series production test u-blox focuses on high quality for its products. All units produced are fully tested automatically in production line. Stringent quality control process has been implemented in the production line. Defective units are analyzed in detail to improve the production quality. This is achieved with automatic test equipment (ATE) in production line, which logs all production and measurement data.
PAGE 131
TOBY-L2 and MPCI-L2 series - System Integration Manual 5.2 Test parameters for OEM manufacturer Because of the testing done by u-blox (with 100% coverage), an OEM manufacturer does not need to repeat firmware tests or measurements of the module RF performance or tests over analog and digital interfaces in their production test.
PAGE 132
TOBY-L2 and MPCI-L2 series - System Integration Manual This feature allows the measurement of the transmitter and receiver power levels to check component assembly related to the module antenna interface and to check other device interfaces from which depends the RF performance. To avoid module damage during transmitter test, a proper antenna according to module specifications or a 50  termination must be connected to ANT1 port.
PAGE 133
TOBY-L2 and MPCI-L2 series - System Integration Manual Appendix A Glossary 3GPP 3rd Generation Partnership Project 8-PSK 8 Phase-Shift Keying modulation 16QAM 16-state Quadrature Amplitude Modulation 64QAM 64-state Quadrature Amplitude Modulation ACM Abstract Control Model ADC Analog to Digital Converter AP Application Processor ASIC Application-Specific Integrated Circuit AT AT Command Interpreter Software Subsystem, or attention CSFB Circuit Switched Fall-Back DC Direct Current DCE
PAGE 134
TOBY-L2 and MPCI-L2 series - System Integration Manual LDO Low-Dropout LGA Land Grid Array LNA Low Noise Amplifier LPDDR Low Power Double Data Rate synchronous dynamic RAM memory LTE Long Term Evolution M2M Machine-to-Machine MBIM Mobile Broadband Interface Model MIMO Multi-Input Multi-Output N/A Not Applicable N.A.
PAGE 135
TOBY-L2 and MPCI-L2 series - System Integration Manual B Migration between TOBY-L1 and TOBY-L2 B.
PAGE 136
TOBY-L2 and MPCI-L2 series - System Integration Manual B.2 Pin-out comparison between TOBY-L1 and TOBY-L2 TOBY-L1 TOBY-L2 Pin No Pin Name Description Pin Name Description 1 RSVD Reserved RSVD Reserved 2 GND Ground GND Ground 3 V_BCKP RTC Supply Output 2.5 V output only RTC backup function not available V_BCKP RTC Supply Input/Output 3.0 V output 1.4 V – 4.
PAGE 137
TOBY-L2 and MPCI-L2 series - System Integration Manual TOBY-L1 TOBY-L2 Pin No Pin Name Description Pin Name Description 50 RSVD Reserved I2S_WA I S Word Alignment / GPIO Not supported by TOBY-L2x0-00S 51 RSVD Reserved I2S_TXD 52 RSVD Reserved 53 RSVD 54 Remarks for migration 2 Reserved  I2S / GPIO I S Data Output / GPIO Not supported by TOBY-L2x0-00S 2 Reserved  I2S / GPIO I2S_CLK I2S Clock / GPIO Not supported by TOBY-L2x0-00S Reserved  I2S / GPIO Reserved I2S_RXD I S D
PAGE 138
TOBY-L2 and MPCI-L2 series - System Integration Manual B.3 Schematic for TOBY-L1 and TOBY-L2 integration Figure 75 shows an example of schematic diagram where a TOBY-L100-00S or TOBY-L2x0-00S module can be integrated into the same application board, using all the available interfaces and functions of the modules. The different mounting options for the external parts are highlighted in different colors as described in the legend, according to the interfaces supported by the relative modules.
PAGE 139
TOBY-L2 and MPCI-L2 series - System Integration Manual Related documents [1] u-blox TOBY-L2 series Data Sheet, Docu No UBX-13004573 [2] u-blox MPCI-L2 series Data Sheet, Docu No UBX-13004749 [3] u-blox AT Commands Manual, Docu No UBX-13002752 [4] u-blox EVK-L20 / EVK-L21 User Guide, Docu No UBX-14000422 [5] u-blox Firmware Update Application Note, Docu No UBX-13001845 [6] Universal Serial Bus Revision 2.0 specification, http://www.usb.org/developers/docs/usb20_docs/ [7] ITU-T Recommendation V.
PAGE 140
TOBY-L2 and MPCI-L2 series - System Integration Manual Revision history Revision Date Name Status / Comments R01 20-Dec-2013 sses Initial release for TOBY-L2 series R02 21-Mar-2014 sses Initial release including MPCI-L2 series UART and GPIOs remarked as not supported by TOBY-L2x0-00S R03 23-Jul-2014 sses Advance Information document status Updated MPCI-L2 descriptions Updated USB description and design-in, including VUSB_DET pin previously RSVD Updated MPCI-L2 thickness and installation guid
PAGE 141
TOBY-L2 and MPCI-L2 series - System Integration Manual Contact For complete contact information visit us at http://www.u-blox.com/ u-blox Offices North, Central and South America u-blox America, Inc. Phone: +1 703 483 3180 E-mail: info_us@u-blox.com Regional Office West Coast: Phone: +1 408 573 3640 E-mail: mailto:info_us@u-blox.com Headquarters Europe, Middle East, Africa u-blox AG Phone: +41 44 722 74 44 E-mail: info@u-blox.com Support: mailto:support@u-blox.