Integration Manual
Table Of Contents
- Preface
- Contents
- 1 System description
- 1.1 Overview
- 1.2 Architecture
- 1.3 Pin-out
- 1.4 Operating modes
- 1.5 Supply interfaces
- 1.5.1 Module supply input (VCC or 3.3Vaux)
- 1.5.1.1 VCC or 3.3Vaux supply requirements
- 1.5.1.2 VCC or 3.3Vaux current consumption in 2G connected-mode
- 1.5.1.3 VCC or 3.3Vaux current consumption in 3G connected mode
- 1.5.1.4 VCC or 3.3Vaux current consumption in LTE connected-mode
- 1.5.1.5 VCC or 3.3Vaux current consumption in cyclic idle/active mode (power saving enabled)
- 1.5.1.6 VCC or 3.3Vaux current consumption in fixed active-mode (power saving disabled)
- 1.5.2 RTC supply input/output (V_BCKP)
- 1.5.3 Generic digital interfaces supply output (V_INT)
- 1.5.1 Module supply input (VCC or 3.3Vaux)
- 1.6 System function interfaces
- 1.7 Antenna interface
- 1.8 SIM interface
- 1.9 Data communication interfaces
- 1.10 Audio
- 1.11 General Purpose Input/Output
- 1.12 Mini PCIe specific signals (W_DISABLE#, LED_WWAN#)
- 1.13 Reserved pins (RSVD)
- 1.14 Not connected pins (NC)
- 1.15 System features
- 1.15.1 Network indication
- 1.15.2 Antenna supervisor
- 1.15.3 Jamming detection
- 1.15.4 IP modes of operation
- 1.15.5 Dual stack IPv4/IPv6
- 1.15.6 TCP/IP and UDP/IP
- 1.15.7 FTP
- 1.15.8 HTTP
- 1.15.9 SSL / TLS
- 1.15.10 Bearer Independent Protocol
- 1.15.11 Wi-Fi integration
- 1.15.12 Firmware update Over AT (FOAT)
- 1.15.13 Firmware update Over The Air (FOTA)
- 1.15.14 Smart temperature management
- 1.15.15 SIM Access Profile (SAP)
- 1.15.16 Power saving
- 2 Design-in
- 2.1 Overview
- 2.2 Supply interfaces
- 2.2.1 Module supply (VCC or 3.3Vaux)
- 2.2.1.1 General guidelines for VCC or 3.3Vaux supply circuit selection and design
- 2.2.1.2 Guidelines for VCC or 3.3Vaux supply circuit design using a switching regulator
- 2.2.1.3 Guidelines for VCC or 3.3Vaux supply circuit design using a Low Drop-Out linear regulator
- 2.2.1.4 Guidelines for VCC supply circuit design using a rechargeable Li-Ion or Li-Pol battery
- 2.2.1.5 Guidelines for VCC supply circuit design using a primary (disposable) battery
- 2.2.1.6 Additional guidelines for VCC or 3.3Vaux supply circuit design
- 2.2.1.7 Guidelines for external battery charging circuit
- 2.2.1.8 Guidelines for external battery charging and power path management circuit
- 2.2.1.9 Guidelines for VCC or 3.3Vaux supply layout design
- 2.2.1.10 Guidelines for grounding layout design
- 2.2.2 RTC supply output (V_BCKP)
- 2.2.3 Generic digital interfaces supply output (V_INT)
- 2.2.1 Module supply (VCC or 3.3Vaux)
- 2.3 System functions interfaces
- 2.4 Antenna interface
- 2.5 SIM interface
- 2.6 Data communication interfaces
- 2.7 Audio interface
- 2.8 General Purpose Input/Output
- 2.9 Mini PCIe specific signals (W_DISABLE#, LED_WWAN#)
- 2.10 Reserved pins (RSVD)
- 2.11 Module placement
- 2.12 TOBY-L2 series module footprint and paste mask
- 2.13 MPCI-L2 series module installation
- 2.14 Thermal guidelines
- 2.15 ESD guidelines
- 2.16 Schematic for TOBY-L2 and MPCI-L2 series module integration
- 2.17 Design-in checklist
- 3 Handling and soldering
- 4 Approvals
- 4.1 Product certification approval overview
- 4.2 US Federal Communications Commission notice
- 4.3 Innovation, Science and Economic Development Canada notice
- 4.4 Brazilian Anatel certification
- 4.5 European Conformance CE mark
- 4.6 Australian Regulatory Compliance Mark
- 4.7 Taiwanese NCC certification
- 4.8 Japanese Giteki certification
- 5 Product testing
- Appendix
- A Migration between TOBY-L1 and TOBY-L2
- B Glossary
- Related documents
- Revision history
- Contact
TOBY-L2 and MPCI-L2 series - System Integration Manual
UBX-13004618 - R26 System description
Page 10 of 162
Table 1 summarizes the TOBY-L2 and MPCI-L2 series main features and interfaces.
Module
LTE
UMTS
GSM
Interfaces
Audio
Features
Grade
LTE FDD category
Bands
HSDPA category
HSUPA catego
ry
Bands
GPRS/EDGE multi
-slot class
Bands
UART
USB 2.0
SDIO (Master)
DDC (I
2
C)
GPIOs
Analog audio
Digital audio
Network indication
Antenna supervisor
MIMO 2x2 / Rx Diversity
Embedded TCP/UDP stack
Embedded HTTP,FTP
FOTA
Dual stack IPv4/IPv6
Standard
Profe
ssional
Automotive
TOBY-L200
4
2,4,5
7,17
24
6
850/900
AWS
1900/2100
12
Quad
♦
●
♦
♦
♦
♦
●
♦
●
♦
♦
♦
●
TOBY-L201
4
2,4,5
13,17
24
6
850/1900
●
●
♦
♦
●
♦
●
●
●
●
●
TOBY-L210
4
1,3,5
7,8,20
24
6
850/900
1900/2100
12
Quad
♦
●
■
■
■
■
●
■
●
■
■
■
●
TOBY-L220
1
4
1,3,5
8,19
24
6
850/900
2100
●
●
●
●
●
▲
●
●
●
●
●
●
●
TOBY-L280
4
1,3,5
7,8,28
24
6
850/900
1900/2100
12
Quad
●
●
●
●
●
●
●
●
●
●
●
●
●
MPCI-L200
4
2,4,5
7,17
24
6
850/900
AWS
1900/2100
12
Quad
●
●
●
♦
♦
♦
●
MPCI-L201
4
2,4,5
13,17
24
6
850/1900
●
●
●
●
●
●
●
MPCI-L210
4
1,3,5
7,8,20
24
6
850/900
1900/2100
12
Quad
●
●
●
■
■
■
●
MPCI-L2201
4
1,3,5
8,19
24
6
850/900
2100
●
●
●
●
●
●
●
MPCI-L280
4
1,3,5
7,8,28
24
6
850/900
1900/2100
12
Quad
●
●
●
●
●
●
●
● = supported by all product versions
♦ = supported by all product versions except versions “00”,”01”
■ = supported by all product versions except versions “00”,”60”
▲ = supported by all product versions except versions “62”
Table 1: TOBY-L2 and MPCI-L2 series main features summary
TOBY-L2 modules provide Voice over LTE (VoLTE)
2
as well as Circuit-Switched-Fall-Back (CSFB)
3
audio capability.
Table 2 reports a summary of cellular radio access technologies characteristics and features of the modules.
1
TOBY-L220-62S and MPCI-L220-62S product versions do not support UMTS Radio Access Technology
2
Not supported by “00”, “01”, “02”, “03”, “60” and “62” product versions.
3
Not supported by “00”, “01”, “60”, TOBY-L201-02S and TOBY-L220-62S product versions.