Integration Manual
Table Of Contents
- Document information
- Contents
- 1 System description
- 1.1 Overview
- 1.2 Applications
- 1.3 Architecture
- 1.4 Pin assignments
- 1.5 Supply interfaces
- 1.6 System function interfaces
- 1.7 Debug
- 1.8 GPIO pins
- 1.9 Analog interfaces
- 1.10 Serial interfaces
- 1.10.1 Universal Asynchronous Receiver/Transmitter (UART)
- 1.10.2 Serial Peripheral Interface (SPI)
- 1.10.3 Quad Serial Peripheral Interface (QSPI)
- 1.10.4 Inter-Integrated Circuit (I2C) interface
- 1.10.5 Pulse Width Modulation (PWM) interface
- 1.10.6 Inter-IC Sound (I2S) interface
- 1.10.7 Pulse Density Modulation (PDM) interface
- 1.10.8 USB 2.0 device interface
- 1.11 Antenna interface
- 1.12 Reserved pins (RSVD)
- 1.13 GND pins
- 2 Software
- 3 Flashing application software
- 4 Design-in
- 5 Handling and soldering
- 6 Regulatory information and requirements
- 6.1 ETSI – European market
- 6.2 FCC/ISED – US/Canadian markets
- 6.3 MIC - Japanese market (pending)
- 6.4 NCC – Taiwanese market (pending)
- 6.5 KCC – South Korean market (pending)
- 6.6 ANATEL Brazil compliance (pending)
- 6.7 Australia and New Zealand regulatory compliance (pending)
- 6.8 South Africa regulatory compliance (pending)
- 6.9 Integration checklist
- 6.10 Pre-approved antennas list
- 7 Technology standards compliance
- 8 Product testing
- Appendix
- A Glossary
- B Antenna reference designs
- Related documents
- Revision history
- Contact
NORA-B1 series - System integration manual
UBX-20027617 - R04 Regulatory information and requirements Page 51 of 61
C1-Public
6.10 Pre-approved antennas list
This section lists the different external antennas that are pre-approved for use together with
NORA-B1 series modules.
☞ Note that not all antennas are approved for use in all markets/regions.
6.10.1 Antenna accessories
Name
U.FL to Reverse Polarity SMA adapter cable
Applicable
modules
NORA-B100, NORA-B101
☞ For NORA-B101 ANT pin, see Appendix B, Antenna reference designs for
information how to integrate the U.FL connector with the module. It is
required to follow this reference design to comply with the NORA-B1
FCC/ISED modular approvals.
Connector
U.FL and Reverse Polarity SMA jack (outer thread and pin)
Impedance
50 Ω
Minimum cable
loss
0.5 dB, The cable loss must be above the minimum cable loss to meet the
regulatory requirements. Minimum cable length 100 mm.
Comment
The Reverse Polarity SMA connector can be mounted in a panel.
Approval
FCC, IC, RED, MIC
4
, NCC
4
, KCC
4
, ANATEL
4
, RCM
4
and ICASA
4
6.10.2 Single band antennas
NORA-B106
Applicable
module
NORA-B106
Manufacturer
ProAnt
Gain
+2 dBi
Impedance
N/A
Size
Integrated into module
Type
PCB trace
Comment
PCB antenna on NORA-B106. Should not be mounted inside a metal enclosure.
Approval
FCC, IC, RED, MIC
4
, NCC
4
, KCC
4
, ANATEL
4
, RCM
4
and ICASA
4
FXP72.07.0053A
Applicable
modules
NORA-B100, NORA-B101
☞ For NORA-B101 ANT pin, see Appendix B, Antenna reference designs for
information how to integrate the U.FL connector with the module. It is
required to follow this reference design to comply with the NORA-B1
FCC/ISED modular approvals.
Manufacturer
Taoglas
Gain
-0.5 dBi
Impedance
50 Ω
Size
30.4 x 30.9 mm
Type
Patch
Connector
U.FL (UMCC), IPEX MHF1
Comment
Should be attached to a plastic enclosure or part for best performance.
To be connected to a U.FL connector.
Approval
FCC, IC, RED, MIC
4
, NCC
4
, KCC
4
, ANATEL
4
, RCM
4
and ICASA
4
4
Pending