Integration Manual
Table Of Contents
- Document information
- Contents
- 1 System description
- 1.1 Overview
- 1.2 Applications
- 1.3 Architecture
- 1.4 Pin assignments
- 1.5 Supply interfaces
- 1.6 System function interfaces
- 1.7 Debug
- 1.8 GPIO pins
- 1.9 Analog interfaces
- 1.10 Serial interfaces
- 1.10.1 Universal Asynchronous Receiver/Transmitter (UART)
- 1.10.2 Serial Peripheral Interface (SPI)
- 1.10.3 Quad Serial Peripheral Interface (QSPI)
- 1.10.4 Inter-Integrated Circuit (I2C) interface
- 1.10.5 Pulse Width Modulation (PWM) interface
- 1.10.6 Inter-IC Sound (I2S) interface
- 1.10.7 Pulse Density Modulation (PDM) interface
- 1.10.8 USB 2.0 device interface
- 1.11 Antenna interface
- 1.12 Reserved pins (RSVD)
- 1.13 GND pins
- 2 Software
- 3 Flashing application software
- 4 Design-in
- 5 Handling and soldering
- 6 Regulatory information and requirements
- 6.1 ETSI – European market
- 6.2 FCC/ISED – US/Canadian markets
- 6.3 MIC - Japanese market (pending)
- 6.4 NCC – Taiwanese market (pending)
- 6.5 KCC – South Korean market (pending)
- 6.6 ANATEL Brazil compliance (pending)
- 6.7 Australia and New Zealand regulatory compliance (pending)
- 6.8 South Africa regulatory compliance (pending)
- 6.9 Integration checklist
- 6.10 Pre-approved antennas list
- 7 Technology standards compliance
- 8 Product testing
- Appendix
- A Glossary
- B Antenna reference designs
- Related documents
- Revision history
- Contact
NORA-B1 series - System integration manual
UBX-20027617 - R04 Regulatory information and requirements Page 48 of 61
C1-Public
6.5.2 End-product labeling requirements
When a product containing a NORA-B1 series module is placed on the South Korean market, the
product must be affixed with a label or marking containing the KCC logo and certification number as
shown in the following figures:
Figure 17: Sample label of an end-product that includes a NORA-B10 series module
6.5.3 End-product user manual requirements
The KCC logo and NORA-B1 certification numbers described in the End-product labeling
requirements must also be included in the end-product user manual.
6.6 ANATEL Brazil compliance (pending)
When a product containing a NORA-B1 module is placed on the Brazilian market, the product must
be affixed with a label or marking containing the ANATEL logo, NORA-B1 Homologation number:
TBD and a statement claiming that the device may not cause harmful interference but must accept
it (Resolution No 506).
Statement translation:
“This equipment operates on a secondary basis and, consequently, must accept harmful
interference, including from stations of the same kind, and may not cause harmful interference to
systems operating on a primary basis.”
When the device is so small or for such use that it is not practicable to place the statement above on
it, the information shall be placed in a prominent location in the instruction manual or pamphlet
supplied to the user or, alternatively, shall be placed on the container in which the device is
marketed.
In case, where the final product will be installed in locations where the end-user is not able to see the
ANATEL logo, NORA-B1 Homologation number and/or this statement, the ANATEL logo, NORA-B1
Homologation number and the statement shall also be included in the end-product manual.
6.7 Australia and New Zealand regulatory compliance (pending)
TBD
TBD
“Este equipamento opera em caráter secundário, isto é, não
tem direito a proteção contra interferência prejudicial, mesmo
de estações do mesmo tipo, e não pode causar interferência a
sistemas operando em caráter primário.”