Integration Manual
Table Of Contents
- Document Information
- Contents
- 1 System description
- 1.1 Overview
- 1.2 Architecture
- 1.3 Pin-out
- 1.4 Operating modes
- 1.5 Power management
- 1.6 System functions
- 1.7 RF connection
- 1.8 (U)SIM interface
- 1.9 Serial communication
- 1.9.1 Serial interfaces configuration
- 1.9.2 Asynchronous serial interface (UART)
- 1.9.2.1 UART features
- 1.9.2.2 UART signal behavior
- 1.9.2.3 UART and power-saving
- 1.9.2.4 UART application circuits
- Providing the full RS-232 functionality (using the complete V.24 link)
- Providing the TxD, RxD, RTS, CTS and DTR lines only (not using the complete V.24 link)
- Providing the TxD, RxD, RTS and CTS lines only (not using the complete V.24 link)
- Providing the TxD and RxD lines only (not using the complete V24 link)
- Additional considerations
- 1.9.3 USB interface
- 1.9.4 SPI interface
- 1.9.5 MUX protocol (3GPP TS 27.010)
- 1.10 DDC (I2C) interface
- 1.11 Audio Interface
- 1.12 General Purpose Input/Output (GPIO)
- 1.13 Reserved pins (RSVD)
- 1.14 Schematic for LISA-U2 module integration
- 1.15 Approvals
- 1.15.1 European Conformance CE mark
- 1.15.2 US Federal Communications Commission notice
- 1.15.3 Innovation, Science, Economic Development Canada notice
- 1.15.4 Australian Regulatory Compliance Mark
- 1.15.5 ICASA Certification
- 1.15.6 KCC Certification
- 1.15.7 ANATEL Certification
- 1.15.8 CCC Certification
- 1.15.9 Giteki Certification
- 2 Design-In
- 3 Features description
- 3.1 Network indication
- 3.2 Antenna detection
- 3.3 Jamming Detection
- 3.4 TCP/IP and UDP/IP
- 3.5 FTP
- 3.6 HTTP
- 3.7 SSL/TLS
- 3.8 Dual stack IPv4/IPv6
- 3.9 AssistNow clients and GNSS integration
- 3.10 Hybrid positioning and CellLocate®
- 3.11 Control Plane Aiding / Location Services (LCS)
- 3.12 Firmware update Over AT (FOAT)
- 3.13 Firmware update Over the Air (FOTA)
- 3.14 In-Band modem (eCall / ERA-GLONASS)
- 3.15 SIM Access Profile (SAP)
- 3.16 Smart Temperature Management
- 3.17 Bearer Independent Protocol
- 3.18 Multi-Level Precedence and Pre-emption Service
- 3.19 Network Friendly Mode
- 3.20 Power saving
- 4 Handling and soldering
- 5 Product Testing
- Appendix
- A Migration from LISA-U1 to LISA-U2 series
- A.1 Checklist for migration
- A.2 Software migration
- A.2.1 Software migration from LISA-U1 series to LISA-U2 series modules
- A.3 Hardware migration
- A.3.1 Hardware migration from LISA-U1 series to LISA-U2 series modules
- A.3.2 Pin-out comparison LISA-U1 series vs. LISA-U2 series
- A.3.3 Layout comparison LISA-U1 series vs. LISA-U2 series
- B Glossary
- Related documents
- Revision history
- Contact
LISA-U2 series - System Integration Manual
UBX-13001118 - R25 Related documents Page 180 of 182
Related documents
[1] u-blox LISA-U2 series Data Sheet, document UBX-13001734
[2] u-blox AT Commands Manual, document UBX-13002752
[3] ITU-T Recommendation V.24, 02-2000. List of definitions for interchange circuits between
data terminal equipment (DTE) and data circuit-terminating equipment (DCE).
http://www.itu.int/rec/T-REC-V.24-200002-I/en
[4] 3GPP TS 27.007 - AT command set for User Equipment (UE)
[5] 3GPP TS 27.005 - Use of Data Terminal Equipment - Data Circuit terminating; Equipment (DTE
- DCE) interface for Short Message Service (SMS) and Cell Broadcast Service (CBS)
[6] 3GPP TS 27.010 - Terminal Equipment to User Equipment (TE-UE) multiplexer protocol
[7] USB Revision 2.0 specification, http://www.usb.org/developers/docs/usb20_docs/
[8] I2C-Bus specification and user manual - NXP Semiconductors,
http://www.nxp.com/documents/user_manual/UM10204.pdf
[9] 3GPP TS 51.010-2 - Technical Specification Group GSM/EDGE Radio Access Network; Mobile
Station (MS) conformance specification; Part 2: Protocol Implementation Conformance
Statement (PICS)
[10] 3GPP TS 34.121-2 - Technical Specification Group Radio Access Network; User Equipment (UE)
conformance specification; Radio transmission and reception (FDD); Part 2: Implementation
Conformance Statement (ICS)
[11] CENELEC EN 61000-4-2: "Electromagnetic compatibility (EMC) - Part 4-2: Testing and
measurement techniques - Electrostatic discharge immunity test".
[12] ETSI EN 301 489-1: “Electromagnetic compatibility and Radio spectrum Matters (ERM);
Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 1:
Common technical requirements”
[13] ETSI EN 301 489-52: "Electromagnetic Compatibility (EMC) standard for radio equipment and
services; Part 52: Specific conditions for Cellular Communication Mobile and portable (UE) radio
and ancillary equipment"
[14] u-blox Multiplexer Implementation Application Note, document UBX-13001887
[15] u-blox GNSS Implementation Application Note, document UBX-13001849
[16] u-blox Firmware Update Application Note, document UBX-13001845
[17] u-blox SPI Interface Application Note, document UBX-13001919
[18] 3GPP TS 23.060 - Technical Specification Group Services and System Aspects; General Packet
Radio Service (GPRS); Service description
[19] u-blox End user test Application Note, document WLS-CS-12002
[20] u-blox Package Information Guide, document GPS-X-11004
[21] SIM Access Profile Interoperability Specification, Revision V11r00, http://www.bluetooth.org
[22] u-blox LISA-U1 / LISA-U2 Audio Application Note, Docu No UBX-13001835
[23] 3GPP TS 26.267 V10.0.0 – eCall Data Transfer; In-band modem solution; General description
[24] BS EN 16062: Intelligent transport systems – eSafety – eCall high level application requirements
[25] ETSI TS 122 101– Service aspects; Service principles (3GPP TS 22.101 v.8.7.0 Rel. 8)
[26] 3GPP TS 44.031 Location Services (LCS); Mobile Station (MS) - Serving Mobile Location Centre
(SMLC) Radio Resource LCS Protocol (RRLP)
[27] 3GPP TS 25.331 Radio Resource Control (RRC); Protocol specification
[28] u-blox LISA-U1 series Data Sheet, document UBX-13002048
☞ For regular updates to u-blox documentation and to receive product change notifications, register
on our homepage (www.u-blox.com).