Integration Manual
Table Of Contents
- Document Information
- Contents
- 1 System description
- 1.1 Overview
- 1.2 Architecture
- 1.3 Pin-out
- 1.4 Operating modes
- 1.5 Power management
- 1.6 System functions
- 1.7 RF connection
- 1.8 (U)SIM interface
- 1.9 Serial communication
- 1.9.1 Serial interfaces configuration
- 1.9.2 Asynchronous serial interface (UART)
- 1.9.2.1 UART features
- 1.9.2.2 UART signal behavior
- 1.9.2.3 UART and power-saving
- 1.9.2.4 UART application circuits
- Providing the full RS-232 functionality (using the complete V.24 link)
- Providing the TxD, RxD, RTS, CTS and DTR lines only (not using the complete V.24 link)
- Providing the TxD, RxD, RTS and CTS lines only (not using the complete V.24 link)
- Providing the TxD and RxD lines only (not using the complete V24 link)
- Additional considerations
- 1.9.3 USB interface
- 1.9.4 SPI interface
- 1.9.5 MUX protocol (3GPP TS 27.010)
- 1.10 DDC (I2C) interface
- 1.11 Audio Interface
- 1.12 General Purpose Input/Output (GPIO)
- 1.13 Reserved pins (RSVD)
- 1.14 Schematic for LISA-U2 module integration
- 1.15 Approvals
- 1.15.1 European Conformance CE mark
- 1.15.2 US Federal Communications Commission notice
- 1.15.3 Innovation, Science, Economic Development Canada notice
- 1.15.4 Australian Regulatory Compliance Mark
- 1.15.5 ICASA Certification
- 1.15.6 KCC Certification
- 1.15.7 ANATEL Certification
- 1.15.8 CCC Certification
- 1.15.9 Giteki Certification
- 2 Design-In
- 3 Features description
- 3.1 Network indication
- 3.2 Antenna detection
- 3.3 Jamming Detection
- 3.4 TCP/IP and UDP/IP
- 3.5 FTP
- 3.6 HTTP
- 3.7 SSL/TLS
- 3.8 Dual stack IPv4/IPv6
- 3.9 AssistNow clients and GNSS integration
- 3.10 Hybrid positioning and CellLocate®
- 3.11 Control Plane Aiding / Location Services (LCS)
- 3.12 Firmware update Over AT (FOAT)
- 3.13 Firmware update Over the Air (FOTA)
- 3.14 In-Band modem (eCall / ERA-GLONASS)
- 3.15 SIM Access Profile (SAP)
- 3.16 Smart Temperature Management
- 3.17 Bearer Independent Protocol
- 3.18 Multi-Level Precedence and Pre-emption Service
- 3.19 Network Friendly Mode
- 3.20 Power saving
- 4 Handling and soldering
- 5 Product Testing
- Appendix
- A Migration from LISA-U1 to LISA-U2 series
- A.1 Checklist for migration
- A.2 Software migration
- A.2.1 Software migration from LISA-U1 series to LISA-U2 series modules
- A.3 Hardware migration
- A.3.1 Hardware migration from LISA-U1 series to LISA-U2 series modules
- A.3.2 Pin-out comparison LISA-U1 series vs. LISA-U2 series
- A.3.3 Layout comparison LISA-U1 series vs. LISA-U2 series
- B Glossary
- Related documents
- Revision history
- Contact
LISA-U2 series - System Integration Manual
UBX-13001118 - R25 System description Page 109 of 182
Radio Frequency spectrum efficiency (Article 3.2):
o EN 301 511
o EN 301 908-1
o EN 301 908-2
Electromagnetic Compatibility (Article 3.1b):
o EN 301 489-1
o EN 301 489-52
Safety (Article 3.1a):
o EN 60950-1
o EN 62311
The conformity assessment procedure for the LISA-U2 series modules, referred to in Article 17 and
detailed in Annex II of the Radio Equipment Directive (2014/53/EU), has been followed.
Thus, the following marking is included in the product:
⚠ Radiofrequency radiation exposure Information: this equipment complies with radiation exposure
limits prescribed for an uncontrolled environment for fixed and mobile use conditions. This
equipment should be installed and operated with a minimum distance of 20 cm between the
radiator and the body of the user or nearby persons. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter except as authorized in the
certification of the product.
⚠ The gain of the system antenna(s) used for LISA-U200 and LISA-U230 modules (i.e. the combined
transmission line, connector, cable losses and radiating element gain) must not exceed 4.37 dBi
(900 MHz, i.e. GSM 900 or UMTS FDD-8 band), 10.45 dBi (1800 MHz, i.e. GSM 1800), 14.10 dBi
(2100 MHz, i.e. UMTS FDD-1 band) for mobile and fixed or mobile operating configurations.
⚠ The gain of the system antenna(s) used for LISA-U201 modules (i.e. the combined transmission
line, connector, cable losses and radiating element gain) must not exceed 5.76 dBi (900 MHz, i.e.
GSM 900 or UMTS FDD-8 band), 11.44 dBi (1800 MHz, i.e. GSM 1800 band), 13.70 dBi (2100 MHz,
i.e. UMTS FDD-1 band) for mobile and fixed or mobile operating configurations.
⚠ The gain of the system antenna(s) used for LISA-U260 modules (i.e. the combined transmission
line, connector, cable losses and radiating element gain) must not exceed 4.11 dBi (900 MHz, i.e.
GSM 900 band), 9.86 dBi (1800 MHz, i.e. GSM 1800 band) for mobile and fixed or mobile operating
configurations.
⚠ The gain of the system antenna(s) used for LISA-U270 modules (i.e. the combined transmission
line, connector, cable losses and radiating element gain) must not exceed 4.22 dBi (900 MHz, i.e.
GSM 900 or UMTS FDD-8 band), 10.50 dBi (1800 MHz, i.e. GSM 1800 band), 14.75 dBi (2100 MHz,
i.e. UMTS FDD-1 band) for mobile and fixed or mobile operating configurations.
1.15.2 US Federal Communications Commission notice
The Federal Communications Commission (FCC) IDs for the LISA-U2 modules are:
LISA-U200: XPYLISAU200
LISA-U201: XPYLISAU201
LISA-U230: XPYLISAU230
LISA-U260: XPYLISAU200
LISA-U270: XPYLISAU200