Precautions ...................................................................................................... 3 The Main Purpose........................................................................................... 4 The Feature of TD-4000A-X .......................................................................... 5 Installation................................................................................................. 6 Management............................................................
Troubleshooting............................................................................................. 30 Additional Information ................................................................................. 31 Package content ............................................................................................ 32 Product Specifications .................................................................................. 33 Tire pressure sensor specifications ...................................
Precautions 1. For alve stem used on Motorcycle, please use lock-fixed type, not in rubber made. 2. Please make sure the LCD display can receive signals from two tire pressure sensors. 3. Tyredog TPMS has unique anti-theft tool to prevent sensor being stolen. You can decide whether install or not. 4. Please double confirm if sensors are fitted tightly. If necessary, please spreading detergent water on the valve stem to check any air leakage. 5.
11. If you have any questions or problems concerning your unit that are not covered in this manual, please consult your nearest Tyredog dealer. The Main Purpose The Tire Pressure Monitoring System (TPMS) is an efficient and effective solution to many of current motorcycle safety problems. TPMS will help prevent driving on deflated tires and reduce fuel consumption. There are benefits here: z Improves ride performance and handling Tire pressure leads to driving condition a lot.
Fuel efficiency is reduced by one percent for every 3 PSI of under inflation. It is for sure that tire pressure is also one of important factors to save gas consumption. z Extends tire life Research finds that running tires 20% under –inflation can reduce tire life by up to 50%.
wireless technology, tire pressure and temperature information is displayed on the friendly Graphic User Interface (LCD monitor). Installation z Do it yourself (D.I.Y.): it can be fully installed in a short time without any technical knowledge z Wireless and cordless: wireless sensors and LCD monitor ensure a quick and easy installation. z Battery-powered: Battery powered LCD monitor and sensor and battery low indicators on the monitor can remind rider of battery power status in all tires.
z Sensors are changeable in the very unlikely event of defect or damage, so down time is minimal z Ensure signal accessibility by providing peripheral signal integrity technology z Strict environmental test has approved its reliability. z Corrosion protection: metal section completely immersed in rust preventative coating for increased service life and reduced downtime.
Sensor description Sensor battery cover Valve stem connection Graphic User Interface and Contents Mute: Monitor status: Initialization Normal Mute on Mute off Monitor power (No icon): normal : battery low Connection Status: Connected No connection Pressure measuring unit: Sensor power status: :battery low (No icon): normal Temperature measuring unit: к / л Tire status: Low Pressure High Pressure High Temperature Pressure Temperature 8
1. System map 2. The installation of LCD monitor Insert batteryΚ A. Prepare one AAA-type battery B. Follow the direction A and B on the picture shown below to take monitor battery cover away.
C. Insert battery with proper direction. D. After battery inserted, the LCD monitor will automatically power on and the display will show graphics as picture below.
E. Close the battery cover onto LCD monitor. 3. The installation of tire pressure sensors As sensor has its own position, you have to make sure its defined position. When inserting batteries in every sensors please don’t mix up sensor caps. Sensor map could give guidance for user to install. Sensor map F. means front tire R.
Insert batteries in sensors Battery installation for tire pressure sensor A. Take away sensor cap in anti-clockwise direction. B. Insert lithium battery and make sure battery polarity correct when insert it. Right now, monitor will receive signals from corresponding sensors and report pressure value on the screen. At first, you will find that the value shows “00.0”. It is because sensors have not been mounted yet. The screen could show as below.
Blinking Take F (front tire) for example NoteΚAfter take away battery, the status of being without battery need to leave for 10 seconds and then insert battery again. It is for resetting system. C. Fit sensor cap in a clockwise direction. Please refer to “sensor map” to make sure the right position of each sensor and please don’t mix up sensor caps either. You will find either sensor cap and sensor body have marks to remind user of its position.
Take F.L. (front left) for example Anti –theft tool for sensor (optional) Anti –theft tool is designed to prevent the possibility of sensors being taken away. Users can decide if it is needed or not.
A. Put anti-theft fixed ring onto valve stem. B. Install sensors onto valve stem. Don’t install sensors by brute force. Now, the display will show you the latest valve of tire pressure.
C. Adjust the anti-theft fixed ring position to install it with sensor in place firmly. D. Put the hex socket screw onto the anti-theft fixed ring. (Please don’t exert excessively to damage the valve.) E. When four tire pressure sensors are installed, please check with detergent water if the tire pressure sensors and tire valve is completely fitted without any air leakage. (spread detergent water on the valve stem) F. The anti-theft tool can be decided to install or not.
Operation instructions 1. Monitor basic function Locations and function buttons Set: pressure unit setting temperature unit setting pressure warning value setting temperature warning value Power switch: on/ off Mute: on/ off Backlight Temperature 2.
MuteΚon/ off Switch to mute mode. The audible warnings will be disable. When push mute button again, it can go back to both audible and visible warning mode. Mute off Mute on Display tire temperature figures Push this button, the LCD monitor will display tire temperature instead of tire pressure for 3 seconds.
Backlight: on/ off When in darkness, you also can check out tire pressure and temperature by pressing backlight button. The backlight will be off after three seconds. 3. Advanced setting mode z Pressure unit setting z Temperature unit setting z Pressure warning value setting z Temperature warning value z Press for over 3 seconds to enter advanced setting mode Make choice by pressing and both values.
A. Set pressure measuring unitΚ Four types of pressure measuring units: PSI,KPA,BAR and ʦ/ʡ 2 are provided here. Users can make their own choices by .
B. Set temperature measuring unit: к and л Two types of temperature measuring units: к and л are provided here. Users can make their own choices by and . C. Set tire pressure lower warning valueΚ The default value is 26 P.S.I., and Users can make their own choices by and .
Blinking D. Set tire pressure upper warning value The default value is 45 P.S.I. and users can make their own choices by and . Blinking E.
The default value is 70 к and users can make their own choices by and . Blinking This mode will return to main screen as long as there is no operation for more than 30 seconds. + Sensor learning mode In a very unlike case, sensor could be broken or missed. Sensor learning mode can provide an alternative way to replace sensors with ‘learnable sensors’. (‘Learnable sensor’ will need to purchase separately.) LCD monitor can reload new identified number only from ‘learnable sensor.
sensors. As long as enter this mode, insert battery into ‘learnable sensor’ immediately, the LCD monitor will beep once and finish learning process. Take F (front tire) for example The ‘learning mode’ will continue for about 30 seconds and then back to main screen.
Operating procedure 1. Initialization Switch on LCD monitor to boot up, and LCD monitor will be communicating with sensors and showing tire pressure values that is kept from last time before system was off. 2. Main screen After booting up for around one minutes, system will enter main screen. Most of time, your system will stay in this mode and response with the latest figures of both tire pressure and temperature. In this mode, you will find the antenna icon will be blinking.
3. Automatically power off A. After power on, if there is no signal from sensors in 20 minutes B. Being no signal received for more than one hour after the last signal received. 4. Abnormal status A. Tire pressure below lower warning value When tire pressure is below lower warning value (default value= 26 PSI), LCD monitor will beep and vibrate once in 10 seconds and repeat for 5 times. Blinking Take F (front tire) for example B.
repeat for 5 times. Blinking Take F (front tire) for example C. Tire temperature higher than upper warning value When tire temperature is higher than upper warning value, (default value= 70к), LCD monitor will beep and vibrate once in 10 seconds and repeat for 5 times. Blinking Take F (front tire) for example D.
E. Tire pressure sensor runs out of power Battery power in sensor will decrease by daily operation and when power level is lower to some extent, the sensor battery low indicator will appear to remind driver of time to replace battery.
The definition of warnings Item Status Purpose Pattern 1. Power on LCD To remind rider of Beeps once monitor power on now Tire pressure is below The warning of Beeps for 3 times, lower warning range low tire pressure vibrating and backlights 2. on. Repeat for 5 times. 3. When tire pressure is The warning of tire Beeps for 3 times, below lower warning pressure getting vibrating and backlights range, each 1 P.S.I. on. Repeat for 5 times. lower down, warnings will be given as well. 4.
warning range, each 1 getting high on. Repeat for 5 times. Learnable sensor is Finish learning Beeps once integrated mode P.S.I. up, warnings will be given as well. 8. Troubleshooting The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. 1. Indications disappear from / do not appear in the display A. Please make sure if power switch is on. B.
D. If these solutions do not help improve the situation, consult your nearest Tyredog dealer. 3. Monitor display color is getting dark. When car temperature is over 80к, it is natural that LCD panel will be getting dark. When car temperature is back to normal, LCD panel will be normal again. 4. When temperature is below -20к, the response time of CD monitor could be slower. 5. ‘Learning mode’ can only accept ‘learnable sensor’ but not standard sensor.
z Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur. z Battery may explode if mistreated. z Do not recharge, disassemble, or dispose of in fire. Package content Here are items in whole package.
User guide 1 piece AAA 1.5V battery 1 piece Product Specifications Tire pressure sensor specifications Frequency 433.92MHz Tire pressure range 0 ~ 60PSI Accuracy Tire pressure ̈́1 PSI Εtire temperature ̈́2 к Operating voltage 3V DC Operating temperature -40к~125к Battery life 1~2 years (depends on working hours per day) Dimensions Diameter 20.5mm X height 20mm Weight 10̈́1 g LCD monitor specifications Frequency 433.92MHz Operating voltage 1.
