Owner's manual

ManualsBrandsTycon Power ManualsPower suppliersUPS-ST24-100-8-UBNT

UPS-ST24 300W UBNT

UPSPro™ Backup

Power System

▫ Wireless Base Stations

▫ Surveillance Cameras

▫ Remote Gate Control

▫ Electric Fence

▫ Up to 192W loads

Congratulations! on your purchase of the UPSPro™ outdoor

backup power system. Please take a moment to review this Qwik

Install Guide before assembly or battery installation.

DANGER! Avoid Powerlines!

You Can Be Killed!

When following the instructions in this guide take extreme care

to avoid contact with overhead power lines, lights and power circuits.

Contact with power lines, lights or power circuits may be fatal. We rec-

ommend to install no closer than 20 feet to any power lines.

Safety: For your own protection, follow these safety rules.

▫ Perform as many functions as possible on the ground

▫ Do not attempt to install on a rainy, windy or snowy day or if

there is ice or snow accumulation at the install site or if the

site is wet.

▫ Make sure there are no people, pets, etc. below when you are

working on a roof or ladder.

Recommended Tools: Phillips Screwdriver, 13mm and

10mm Open End Wrench, 8mm nut driver, Flat Blade Screwdriv-

Please help preserve the environment and return

used batteries to an authorized depot

Summary of content (8 pages)

PAGE 1
UPS-ST24 300W UBNT UPSPro™ Backup Power System ▫ Wireless Base Stations ▫ Surveillance Cameras ▫ Remote Gate Control ▫ Electric Fence ▫ Up to 192W loads Congratulations! on your purchase of the UPSPro™ outdoor backup power system. Please take a moment to review this Qwik Install Guide before assembly or battery installation.
PAGE 2
Qwik Install STEP 1: Add Grounding Wire Between Door and Enclosure: Remove plastic covers on copper studs on inside of door and inside of enclosure. Add jumper wire between 2 copper studs and use copper washers and nuts to secure. STEP 2: Add wire feedthrus into the bottom connector plate. Attach the connector plate to the bottom of the enclosure using self tapping screws provided. STEP 3: Install hole plug in drain hole in bottom right corner of the enclosure.
PAGE 3
STEP 4: If pole mounting the enclosure, assemble the pole mount kit to the back of the enclosure and mount the enclosure to a pole using the 6 hose clamps provided. The enclosure can also be wall mounted using the 4 holes in the back of the enclosure. STEP 5: Insert the battery platform in the bottom of the enclosure. The battery platform has cutouts so wires can be routed under the battery as needed. STEP 6: Attach the green DIN Rail adapters to the 8 port POE switch using the screws provided.
PAGE 4
STEP 8: If batteries are installed on their side make sure to apply an insulator to the top of the battery terminal to prevent the battery terminals from shorting to the metal enclosure in case the battery shifts inside the enclosure during an earthquake. STEP 9: Set the proper voltage on the AC input of the controller by removing the metal tab and then switching the input voltage to 120VAC or 240VAC depending on your source voltage.
PAGE 5
STEP 12: Switch off controller and connect AC to the controller. Be sure to follow local regulations for outdoor 120/240VAC connections. STEP 13: Connect the load to the controller LOAD terminals. Be sure to observe proper polarity. Switch on the controller to activate the charging. STEP 14: Plug or Tighten all wire feedthrus. If they don ’t tighten on a small diameter wire, you can wrap some electrical tape around the wire in the seal area to increase its diameter and make a better seal.
PAGE 6
SPECIFICATIONS Subject to change without notice UPS-ST24-UBNT Load Voltage (DC) 24V +/- 5% Max Load Output 12A Min Load Output 1A 2 battery 51Ah 1200VA 4 battery 102Ah 2400VA Available Storage Capacities Valve Regulated Sealed Lead Acid / GEL Battery Type Battery Life 5 Years WET Equalize = 28.8V, Float = 26.4V GEL Equalize = 28.4V, Float = 27V Charge Voltage 21.5V Load Off 25.2V Load On Over-discharge protection Self Consumption POE Switch Output <5.
PAGE 7
3. VENTING: The enclosure is vented thru the wire feedthrus and various hole plugs in the bottom of the enclosure. Don’t make these airtight with silicon 4. BATTERY MAINTENANCE: The batteries used in the UPSPro systems don’t require any maintenance. They should last up to 5 years in normal use. Note: Never store batteries for any length of time in a discharged state or it will kill the battery. 5. BATTERY OVERDISCHARGE: We highly recommend hooking all equipment loads to the controller voltage output.
PAGE 8
000027 Rev 1 UPS-ST24 300W UBNT UPSPro™ Qwik Install Guide 8