Specifications

ManualsBrandsTyan ManualsMotherboardsS7002

S7002

Version 1.00

this manual may be reproduced or translated without prior written consent from

MiTAC Computer Corp.

Trademark

All registered and unregistered trademarks and company names contained in

this manual are property of their respective owners including, but not limited to

the following.

TYAN

is a trademark of MiTAC Computer Corporation

Intel

is a trademark of Intel

Corporation.

AMI

, AMIBIOS

and combinations thereof are trademarks of AMI Technologies.

Microsoft

, Windows

are trademarks of Microsoft Corporation.

IBM

, PC

, AT

and PS/2

are trademarks of IBM Corporation.

Winbond

is a trademark of Winbond Electronics Corporation.

Notice

Information contained in this document is furnished by MiTAC Computer

Corporation and has been reviewed for accuracy and reliability prior to printing.

MiTAC assumes no liability whatsoever, and disclaims any express or implied

warranty, relating to sale and/or use of TYAN

products including liability or

warranties relating to fitness for a particular purpose or merchantability. MiTAC

retains the right to make changes to product descriptions and/or specifications

at any time, without notice. In no event will MiTAC be held liable for any direct

or indirect, incidental or consequential damage, loss of use, loss of data or other

malady resulting from errors or inaccuracies of information contained in this

document.

Summary of content (100 pages)

PAGE 1
S7002 Version 1.00 Copyright Copyright © MiTAC Computer Corporation, 2009. All rights reserved. No part of this manual may be reproduced or translated without prior written consent from MiTAC Computer Corp. Trademark All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. TYAN® is a trademark of MiTAC Computer Corporation ® ® Intel is a trademark of Intel Corporation.
PAGE 2
http://www.TYAN.
PAGE 3
Contents Before you begin… ...........................................................................5 Chapter 1: Instruction .......................................................................7 1.1 - Congratulations ..........................................................................................7 1.2 - Hardware Specifications.............................................................................7 1.3 - Software Specifications ............................................................
PAGE 4
Appendix: How to Make a Driver Diskette.....................................91 Glossary...........................................................................................93 Technical Support ...........................................................................99 4 http://www.TYAN.
PAGE 5
Before you begin… Check the box contents! The retail motherboard package should contain the following: 1x S7002 Motherboard 6 x SATA Cable 1 x S7002 User’s manual 1 x S7002 Quick reference guide 1 x TYAN® Driver CD 1 x I/O shield 5 http://www.TYAN.
PAGE 6
http://www.TYAN.
PAGE 7
Chapter 1: Instruction 1.1 - Congratulations You have purchased one of the most powerful server solutions based on the Intel® Tylersburg chipset. The TYAN® S7002 series motherboard is designed to ® support up to two Intel Nehalem-EP 2S processors and up to 64GB DDR3800/1066/1333 memory.
PAGE 8
Connector type D-Sub 15pin(Embedded VGA) Resolution 1600x1200@60Hz Chipset Aspeed AST2050 USB (8) USB2.
PAGE 9
Optional accessories for future upgrade I/O Shield Cable Riser Card (1) I/O Shield (6) SATA signal cables M2083-RS, PCI-E 1U riser card (left) (1) CCBL-0615, COM port cable / (1) CCBL-0311, SATA 1-to-2 power cable / (1) CCBL-035J, USB bracket cable Cable TYAN S7002 (S7002WGM2NR) Processor Supported CPU Series Intel Xeon 5500 series QC/DC processors Socket Type / QTY LGA1366 / (2) Thermal Design Power (TDP) wattage Chipset Memory 130W System Bus (MHz) Intel QuickPath Interconnect (QPI) IOH /
PAGE 10
Connector Graphic type Resolution 1600x1200@60Hz Chipset Aspeed AST2050 USB (8) USB2.
PAGE 11
Form Factor Form Factor Board Dimension Operation System Regulation OS supported list SSI CEB 12"x10.5" (305x267mm) Please refer to our OS supported list.
PAGE 12
Memory Expansion Slots DIMM Type / Speed DDR3 800/1066/1333 RDIMM, UDIMM Capacity Up to 64GB Memory channel 6 channels (3-channel per CPU) Memory voltage 1.5V (1) PCI-E x16 slot (Gen 2) / (2) PCI-E x8 slots (w/ PCI-E x4 link) Recommended TYAN Riser Card LAN Port QTY (2) Controller Intel 82574 SAS Storage SATA Graphic Connector (8) Controller LSI SAS1068E Speed 3.0 Gb/s RAID S/W RAID 0,1,1E standard Connector (6) Controller ICH10R Speed 3.
PAGE 13
Monitors temperature for CPU & system Temperature System Monitoring environment Fan fail LED indicator / Over temperature LED warning indicator Chassis intrusion detection / Watch Dog timer Others support Onboard Chipset Onboard Aspeed AST2050 IPMI 2.0 compliant baseboard management AST2050 IPMI Feature Server Management controller (BMC) / Supports storage over IP and remote platform-flash/ BIOS update / USB 2.
PAGE 14
Riser Optional accessories for future upgrade Card M2083-RS, PCI-E 1U riser card (left) (1) CCBL-0615, COM port cable / (1) SAS cable for Cable S7002 / (1) CCBL-0311, SATA 1-to-2 power cable / (1) CCBL-035J, USB bracket cable TYAN S7002-LE (S7002GM2NR-LE) Processor Chipset Supported CPU Series Intel Xeon 5500 series QC/DC processors Socket Type / QTY LGA1366 / (2) Thermal Design Power (TDP) wattage 130W System Bus (MHz) 1333/1066/800 IOH / ICH Intel 5500 / ICH10R Super I/O Winbond W83627
PAGE 15
Connector Graphic Input /Output type Resolution 1600x1200@60Hz Chipset Aspeed AST2050 USB (8) USB2.
PAGE 16
Operation System Regulation OS supported list Please refer to our OS supported list. FCC (Doc) Class B CE (Doc) Yes Operating Temp 10° C ~ 35° C (50° F~ 95° F) Non-operating Operating Temp Environment In/Non-operating Humidity RoHS 6/6 RoHS Complaint Accessory list 90%, non-condensing at 35° C Yes Motherboard (1) TYAN motherboard Manual (1) User's manual / (1) Quick Ref.
PAGE 17
Chapter 2: Board Installation You are now ready to install your motherboard. How to install our products right… the first time The first thing you should do is reading this user’s manual. It contains important information that will make configuration and setup much easier. Here are some precautions you should take when installing your motherboard: (1) Ground yourself properly before removing your motherboard from the antistatic bag.
PAGE 18
2.1 - Board Image This diagram is representative of the latest motherboard (S7002WAP2NR) revision available at the time of publishing. The board you receive may not look exactly like the above diagram. 18 http://www.TYAN.
PAGE 19
2.2 - Block Diagram S7002 Block Diagram (Represents all SKUs) 19 http://www.TYAN.
PAGE 20
2.3 - Board Parts, Jumpers and Connectors This diagram is representative of the latest board revision (S7002WAP2NR) available at the time of publishing. The board you receive may not look exactly like the above diagram. 20 http://www.TYAN.
PAGE 21
Jumpers & Connectors Jumper/Connector Function J36/J37/J40/J41/J42/J47/J48/J49/J50/J56 Fan connectors J16 COM2 Header J19/J20 Front USB Header J25 Front Panel Audio J35 Front Panel Header J43 Clear CMOS J44 PSMI Connector J46 IPMB Pin Header J21/J51 SAS SGPIO Header J52 BMC RST Button JP1 Clear CMOS On Board SAS LSI1068E EN/DIS COM2 Select JP7 JP8/JP9 Jumper Legend OPEN - Jumper OFF Without jumper cover CLOSED - Jumper ON With jumper cover 21 http://www.TYAN.
PAGE 22
Jumper Placement J37 J36 J41 J42 J40 J36/J37/J40/J41/J42: 4-Pin FAN Connector Pin_1 Pin 1 2 3 4 Signal GND +12V FAN_TACH FAN_PWM 22 http://www.TYAN.
PAGE 23
J47 J48 J50 J56 J49 J47/J48/J49/J50/J56: 8-Pin FAN Connector Pin_1 Pin Signal Pin Signal 1 PWM 5 GND 2 VDD_12_RUN 6 TACHIN 23 http://www.TYAN.
PAGE 24
J19 J25 J20 J16 J35 J16: Com2 Header Signal DCD RXD TXD DTR GND Pin 1 3 5 7 9 24 http://www.TYAN.
PAGE 25
J19/J20: Front USB Header Signal +5V USB DATA1USBDATA1+ GND Key Pin 1 3 5 7 9 Signal MIC2-L MIC2-R LINE2-R FP IO Sense LINE2-R Pin 1 3 5 7 9 Pin 2 4 6 8 10 Signal +5V USB DATA2USBDATA2+ GND GND J25: Front Panel Audio Pin 2 4 6 8 10 Signal GND FP_Present MIC2-JD Key LINE2-JD J35: Front Panel Header Signal PW_LED+ KEY PW_LEDHD_ LED+ HD_ LEDPW_SW# GND RST_SW# GND SYS_ID_SW# GND NMI_SW# Pin 1 3 5 7 9 11 13 15 17 19 21 23 Pin 2 4 6 8 10 12 14 16 18 20 22 24 25 http://www.TYAN.com Signal FP_PWER(3.
PAGE 26
J44 J46 J51 J21 J52 J43 J21/J51 SAS SGPIO Header Signal SCL SDA GND KEY NC Pin 1 3 5 7 9 Pin 2 4 6 8 10 26 http://www.TYAN.
PAGE 27
J43: Fan Connector for Barebones Systems Pin_1 2 19 20 Signal TACH1 TACH2 TACH3 TACH4 TACH5 GND PWM2 TACH11 TACH12 NC Pin 1 3 5 7 9 11 13 15 17 19 Pin 2 4 6 8 10 12 14 16 18 20 Signal TACH6 TACH7 TACH8 TACH9 TACH10 KEY PIN PWM1 TACH13 TACH14 PWM3 J44: PSMI Connector Pin 1 2 3 4 5 Pin_1 Signal SMB_CLK SMB_DAT PSU_SMBALERT_N GND V3.3 J46: IPMB Connector Pin_1 Pin 1 2 3 4 Signal IPMB DATA GND IPMB CLK NC J52 BMC RST Button Pin_1 Pin Signal 1 RST# 27 http://www.TYAN.
PAGE 28
JP8 JP7 JP1 JP9 JP1: Clear CMOS Pin_3 Pin_1 Normal (Default) Pin_3 Pin_1 Clear CMOS You can reset the CMOS settings by using this jumper if you have forgotten your system/setup password or need to clear system BIOS setting. Power off system and disconnect both power connectors from the motherboard Put jumper cap back to Pin_1 and Pin_2 (default setting) Use jumper cap to close Pin_2 and Pin_3 for several seconds to Clear CMOS Reconnect power & power on system 28 http://www.TYAN.
PAGE 29
JP7 On Board SAS LSI1068E Enabled/Disabled Pin_3 Pin_1 Pin 1 2 3 Pin_3 Pin_1 Signal PLTRST# SAS_RST# GND Note: Pin1-2: Enable onboard SAS chip; Pin2-3: Disable onboard SAS chip JP8/JP9: COM2 Select Pin_3 Pin_1 Pin 1 2 3 Pin_3 Pin_1 Signal SIO RX COM2_RX BMC RX Note: Pin1-2: SIO to COM2; Pin2-3: BMC UART2 to COM2 29 http://www.TYAN.
PAGE 30
2.4 - Installing the Processor Your brand new S7002 supports the latest Tylersburg platform from Intel®. ® Only Intel “Nehalem-EP 2S” processors are certified and supported with this motherboard. Check our website for latest processor support. http://www.TYAN.com TYAN® is not liable for damage as a result of operating an unsupp-orted configuration. Step1: Press the lever and unlock the CPU socket.
PAGE 31
B Step3: Close the socket cover and press the CPU lever down to secure the CPU. 31 http://www.TYAN.
PAGE 32
2.5 - Heat sink Installation After installing the processor, you should proceed to install the heat sink. The CPU heat sink will ensure that the processor do not overheat and continue to operate at maximum performance for as long as you own them. The overheated processor is dangerous to the motherboard. For the safest method of installation and information on choosing the appropriate heat sink, using heat sinks validated by Intel®. Please refer to Intel’ ®s website at www.Intel.
PAGE 33
2.6 - Thermal Interface Material There are two types of thermal interface materials designed for use with the processors. The most common material comes as a small pad attached to the heat sink at the time of purchase. There should be a protective cover over the material. Take care not to touch this material. Simply remove the protective cover and place the heat sink on the processor. The second type of interface material is usually packaged separately. It is commonly referred to as ‘thermal compound’.
PAGE 34
2.7 - Finishing Installing the Heat sink After you have finished installing the heat sink onto the processor and socket, attach the end wire of the fan (which should already be attached to the heat sink) to the motherboard. The following diagram illustrates how to connect fans onto the motherboard. Once you have finished installing all the fans you can connect your drives (hard drives, CD-ROM drives, etc.) to your motherboard. 34 http://www.TYAN.
PAGE 35
2.8 - Tips on Installing Motherboard in Chassis Before installing your motherboard, make sure your chassis has the necessary motherboard support studs installed. These studs are usually metal and are gold in color. Usually, the chassis manufacturer will preinstall the support studs. If you are unsure of stud placement, simply lay the motherboard inside the chassis and align the screw holes of the motherboard to the studs inside the case.
PAGE 36
Some chassis’ include plastic studs instead of metal. Although the plastic studs are usable, TYAN® recommends using metal studs with screws that will fasten the motherboard more securely in place. Below is a chart detailing what the most common motherboard studs look like and how they should be installed. 36 http://www.TYAN.
PAGE 37
2.9 - Installing the Memory Before installing memory, ensure that the memory you have is compatible with the motherboard and processor. ® Check the TYAN Web site at: www.TYAN.com for details of the type of memory recommended for your motherboard. The following diagram shows common types of DDR3 memory modules. • • • TYAN® S7002 series support up to 64GB DDR3 memory. DDR3 800/1066/1333 RDIMM, UDIMM are supported. All installed memory will automatically be detected and no jumpers or settings need changing.
PAGE 38
2. Single CPU installed (CPU1 Only) Quantity of memory DIMM Slot CPU0 DIMM CPU0 DIMM CPU0 DIMM CPU0 DIMM CPU1 DIMM CPU1 DIMM CPU1 DIMM CPU1 DIMM CHA1 CHA0 CHB0 CHC0 CHD1 CHD0 CHE0 CHF0 1 2 3 4 √ √ √ √ √ √ √ √ √ √ 3.
PAGE 39
Memory Installation Procedure Follow these instructions to install memory modules into the S7002. 1. Press the locking levers in the direction shown in the following illustration. 2. Align the memory module with the socket. The memory module is keyed to fit only one way in the socket. KEY SLOT 3. Seat the module firmly into the socket by gently pressing down until it sits flush with the socket. The locking levers pop up into place. 39 http://www.TYAN.
PAGE 40
2.10 - Attaching Drive Cables Attaching Serial ATA Cables S7002 is equipped with 6 Serial ATA (SATA) channels. Connections for the drives are very simple. There is no need to set Master/Slave jumpers on SATA drives. If you are in need of SATA/SAS cables or power adapters please contact your place of purchase. The following pictures illustrate how to connect an SATA drive 1. SATA drive cable connection 2. SATA drive power connection 3. SATA cable motherboard connector 4.
PAGE 41
2.11 - Installing Add-In Cards Before installing add-in cards, it’s helpful to know if they are fully compatible with your motherboard. For this reason, we’ve provided the diagrams below, showing the slots that may appear on your motherboard. PCI-E x 16 slot PCI-E x 8 slot Simply find the appropriate slot for your add-in card and insert the card firmly. Do not force any add-in cards into any slots if they do not seat in place.
PAGE 42
2.12 - Installing I/O Shield Before you connect external devices, check your motherboard package and take out the I/O shield. Follow the instructions below to install the I/O shield to your rear panel. Preparation Flat-head screw driver x 1 Long nose pliers x 1 Protective gloves x 1 I/O shield x 1 Caution To avoid the risk of personal injury, always wear gloves when handling the I/O shield. Each optional covered section has a breaking point, which will allow for the safe removal of the cover.
PAGE 43
2.13 - Connecting External Devices Your motherboard supports a number of different interfaces through connecting peripherals. See the following diagrams for the details. COM port KB/MS RJ45 (share with BMC) 2 x USB2.0 RJ45 Stacked USB2.0 VGA port Audio Note: Peripheral devices can be plugged straight into any of these ports but software may be required to complete the installation. Onboard LAN LED Color Definition The three onboard Ethernet ports have green and yellow LEDs to indicate LAN status.
PAGE 44
2.14 - Installing the Power Supply There are three power connectors on your S7002.The S7002 supports EPS12V/SSI power supplies. PW2 PW1 PW3 PWR2/3: 8-Pin EPS 12V PWR Connector Signal GND GND GND GND Pin 1 2 3 4 Pin 5 6 7 8 44 http://www.TYAN.
PAGE 45
PW1: 24-Pin EPS 12V PWR main Connector Signal +3.3V +3.3V GND +5V GND +5V GND PWRGD 5VSB +12V +12V +3.3V Pin 1 2 3 4 5 6 7 8 9 10 11 12 Pin 13 14 15 16 17 18 19 20 21 22 23 24 Signal +3.3V -12V GND PS_ON GND GND GND Reset +5V +5V +5V GND We suggest using a 1000W or higher power supply. A 1000W is sufficient for most common system configurations, however a higher wattage solution may be needed if the system is fully loaded. Look to the www.TYAN.com website for further information.
PAGE 46
http://www.TYAN.
PAGE 47
Chapter 3: BIOS Setup 3.1 - About the BIOS The BIOS is the basic input/output system, the firmware on the motherboard that enables your hardware to interface with your software. The BIOS determines what a computer can do without accessing programs from a disk. The BIOS contains all the code required to control the keyboard, display screen, disk drives, serial communications, and a number of miscellaneous functions. This chapter describes the various BIOS settings that can be used to configure your system.
PAGE 48
3.3 - Setup Basics The table below shows how to navigate in the setup program using the keyboard.
PAGE 49
3.6 - BIOS Main Menu The Main BIOS Menu is the first screen that you can navigate. The Main BIOS setup menu screen has two main frames. The left frame displays all the options that can be configured. "Grayed-out" options cannot be configured, options in blue can be changed. The right frame displays the key legend. Above the key legend is an area reserved for a text message. When an option is selected in the left frame, it is highlighted in white. Often, a text message will accompany it.
PAGE 50
3.7 - BIOS Advanced Menu You can select any of the items in the left frame of the screen, such as Super I/O Configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the keys. All Advanced BIOS Setup options are described in this section. The Advanced BIOS Setup screen is shown below. The sub menus are described on the following pages.
PAGE 51
Feature Advanced Settings Remote Access Configuration Trusted Computing Configuration On board Devices Configuration Option Description Menu Item Configure Remote Access Menu Item Menu Item Configure settings related to Trusted Computing Information Onboard Devices and PCI Add-On cards Enable/Disable 3.7.1 - CPU Configuration You can use this screen to view CPU Configuration Menu. Use the up and down arrow (Ç/È) keys to select an item.
PAGE 52
Feature CPU Configuration Manufacturer Frequency BCLK Speed Cache L1 Cache L2 Ratio Status Ratio Actual Value Option Read only Enabled C1E Support Disabled Enabled Hardware Prefetcher Disabled Enabled Adjacent Cache Line Prefetch Max CPUID Value Limit Intel (R) Virtualization Tech Execute-Disable Bit Capability Intel (R) HT Technology Active Processor Cores A20M ® Intel SpeedStep Tech ® Intel Tech ® TM TurboMode Intel C-STATE Tech Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enab
PAGE 53
Feature C State package limit setting C1 Auto Demotion Option Auto C1 C3 C6 C7 Enabled C3 Auto Demotion Disabled Enabled Disabled Description Selected option will program into C state package limit register. When enabled, CPU will conditionally demote C3/C6/C7 requests to C1 based on uncore auto-demote information. When enabled, CPU will conditionally demote C6/C7 requests to C3 based on uncore auto-demote information. 3.7.
PAGE 54
Feature IDE Configuration SATA Configuration Configure SATA as Option Description Disabled Compatible Enhanced IDE RAID AHCI Configure SATA devices Select legacy IDE, RAID or AHCI as the SATA interface. Disabled Hard Disk Write Protect Enabled IDE Detect Time Out (Sec) 0~35 (at 5 interval) Enable/Disable device write protection. This will be effective only if device is accessed through BIOS. Select the time out value for detecting ATA/ATAPI device(s). 3.7.
PAGE 55
Feature Option Description Configure Win627 Super I/O Chipset Serial Port1 Address Serial Port2 Address Chassis Intrusion Detect 3F8 IRQ4 3E8 IRQ4 2E8 IRQ3 Disabled 3F8 IRQ4 3E8 IRQ4 2E8 IRQ3 2F8 IRQ3 Disabled Disabled Enabled Disabled POST Watchdog Mode OS Power ON Allow BIOS to select Serial Port1 Base Addresses. Allow BIOS to select Serial Port2 Base Addresses. Enable/Disable the function of chassis intrusion detection.
PAGE 56
3.7.4 - USB Configuration Sub- Menu You can use this screen to view the USB Configuration Menu. Use the up and down arrow (Ç/È) keys to select an item. Use the Plus and Minus (+/-) keys to change the value of the selected option. The settings are described on the following pages. Main Advanced BIOS Setup Utility PCI/PnP Boot Security USB Configuration Module Version – X.XX.X-XX.
PAGE 57
3.7.4.
PAGE 58
3.7.5 - ACPI Configuration Sub-Menu Use this screen to select options for ACPI. Use the up and down arrow (Ç/È) keys to select an item. Use the Plus and Minus (+/-) keys to change the value of the selected option. A description of the selected item appears on the right side of the screen. The settings are described on this page. The screen is shown below.
PAGE 59
Feature Option Description Advanced ACPI Configuration ACPI v1.0 ACPI v2.0 ACPI v3.0 Disabled Enabled Disabled Enabled ACPI Version Features ACPI APIC Support AMI OEMB table Disabled Headless mode Enabled Choose ACPI version Include ACPI APIC table pointer to RSDT pointer list. Include OEMB table pointer to R(X) SDT pointer lists. Enable/Disable Headless operation mode through ACPI. 3.7.5.
PAGE 60
Feature Option FED00000h FED01000h FED02000h FED03000h HPET Memory Address Description Choose HPET Memory Address 3.7.6 - AHCI Configuration Sub- Menu You can use this screen to view the AHCI Configuration Menu. Use the up and down arrow (Ç/È) keys to select an item. Use the Plus and Minus (+/-) keys to change the value of the selected option. The settings are described on the following pages.
PAGE 61
3.7.6.1 - AHCI Port Sub- Menu Main Advanced AHCI PORT X Device : Not Detected SATA Port X S.M.A.R.T. BIOS Setup Utility PCI/PnP Boot Security Chipset Exit Select the type of device connected to the system. [AUTO] [Enabled] ← → Select Screen ↑↓ Select Item +/- Change Option F1 General Help F10 Save and Exit ESC Exit Feature AHCI Port X SATA Port X S.M.A.R.T. Option Description AUTO Select the type of device connected to the system. Not Installed Disabled Enabled S.M.A.R.T.
PAGE 62
3.7.7 - Hardware Health Configuration Sub-Menu You can use this screen to view the Hardware Health Configuration Settings. Use the up and down arrow (Ç/È) keys to select an item. Use the Plus and Minus (+/-) keys to change the value of the selected option. The settings are described on the following pages. BIOS Setup Utility Main Advanced PCI/PnP Boot Security Chipset Exit Hardware Health Configuration Enables Hardware H/W Health Function [Enabled] Health Monitoring Auto FAN Control [Disabled] Device.
PAGE 63
3.7.7.1 Sensor Data Register Monitoring Sub-Menu Main Advanced CPU0 Below Tmax CPU1 Below Tmax IOH Temp ICH Temp CPU0 VCORE CPU1 VCORE 3.3V +12V VBAT CPU FAN0 CPU FAN1 FAN1 FAN2 FAN3 FAN4 FAN5 FAN6 FAN7 FAN8 FAN9 FAN10 BIOS Setup Utility PCI/PnP Boot Security Chipset Exit o : xx C o : xx C o : xx C o : xx C : x.xxx V : x.xxx V : x.xxx V : x.xxx V : x.xxxvV : xxxx RPM : xxxx RPM : xxxx RPM : xxxx RPM : xxxx RPM : xxxx RPM : xxxx RPM : xxxx RPM : xxxx RPM : xxxx RPM : xxxx RPM : xxxx RPM Read only.
PAGE 64
3.7.8 IPMI 2.0 Configuration Sub-Menu You can use this screen to view the IPMI 2.0 Configuration Settings. Use the up and down arrow (Ç/È) keys to select an item. Use the Plus and Minus (+/-) keys to change the value of the selected option. The settings are described on the following pages. Main Advanced IPMI 2.
PAGE 65
3.7.8.1 View BMC System Event Log Sub-Menu Main BIOS Setup Utility PCI/PnP Boot Security Advanced Total Number of Entries: 260 Exit Use +/- to traverse the event log. [1] xxxx xxxx (System Event) MM DD, YYYY HH:MM:SS xxxx xx (IPMI Ver 2.
PAGE 66
3.7.8.3 LAN Configuration Sub-Menu Main BIOS Setup Utility PCI/PnP Boot Security Advanced LAN Configuration Channel Number Channel Number Status [1] Channel number is OK IP Address Configuration IPMI DHCP Current IP Address in BMC [DHCP] xxx.xxx.xxx.xxx Current MAC Address in BMC xxx.xxx.xxx.xxx Subnet Mask Configuration Subnet Mask Current Subnet Mask in BMC [xxx.xxx.xxx.xxx] [xxx.xxx.xxx.xxx] Feature Option Chipset Exit Enter channel number for SET LAN config. command.
PAGE 67
3.7.9 Intel VT-d Configuration Sub-Menu You can use this screen to view the Intel VT-d Configuration Settings. Use the up and down arrow (Ç/È) keys to select an item. Use the Plus and Minus (+/-) keys to change the value of the selected option. The settings are described on the following pages.
PAGE 68
3.7.10 - PCI Express Configuration Sub-Menu Main Advanced BIOS Setup Utility PCI/PnP Boot Security PCI Express Configuration Active State Power-Management [Disabled] Chipset Exit Enable/Disable PCI Express L0s and L1 link power status. ← → Select Screen ↑↓ Select Item +/- Change Option F1 General Help F10 Save and Exit ESC Exit Feature PCI Express Configuration Option Disabled Active State PowerManagement Enabled Description Enables/Disable PCI Express L0s and L1 link power states. 3.7.
PAGE 69
Feature Option Description Configure Remote Access type and parameters Enabled Enables remote access to system Remote Access through serial port. Disabled NOTE: The items listed below will appear when Remote Access is set to [Enabled]. COM1 Serial Port Number COM2 Base Address, IRQ Select Serial Port for console redirection. Make sure the selected port is enabled. Read only 115200 8,n,1 57600 8,n,1 Serial Port Mode 38400 8, n, 1 Select Serial Port settings.
PAGE 70
3.7.12 - On board Devices Configuration Sub-Menu You can use this screen to view the Trusted Computing Configuration Menu. Use the up and down arrow (Ç/È) keys to select an item. Use the Plus and Minus (+/-) keys to change the value of the selected option. The settings are described on the following pages.
PAGE 71
Clearing the TPM is the process of returning the TPM to factory defaults. It is possible the platform owner will change when in this state. Are you sure you want to clear it? OK Cancel 3.7.13 - On board Devices Configuration Sub-Menu You can use this screen to view the Onboard Devices Configuration Menu. Use the up and down arrow (Ç/È) keys to select an item. Use the Plus and Minus (+/-) keys to change the value of the selected option. The settings are described on the following pages.
PAGE 72
Feature Option Description Onboard Device and PCI Slots Configuration Auto Select which graphics controller Boots Graphic Adapter to use as the primary boot Onboard Priority device. VGA Marvell Chip Enabled Disabled Lan1 Lan1 OP-ROM Lan2 Lan2 OP-ROM Auto Enabled Disabled Enabled Disabled Auto Enabled Disabled Enabled Disabled Enable/Disable onboard VGA chip. Note: Do not disable if you have not other VGA card attachment.
PAGE 73
3.8 - PCI PnP Menu You can use this screen to view PnP (Plug & Play) BIOS Configuration Menu. This menu allows the user to configure how the BIOS assigns resources & resolves conflicts. Use the up and down arrow (Ç/È) keys to select an item. Use the Plus and Minus (+/-) keys to change the value of the selected option. The settings are described on the following pages. Main Advanced BIOS Setup Utility PCI/PnP Boot Security Chipset Exit Clear NVRAM during System Boot.
PAGE 74
Feature Allocate IRQ to PCI VGA Option Yes No Disabled Palette Snooping Enabled Disabled PCI IDE BusMaster Enabled Reserved Description Yes: assigns IRQ to PCI VGA card if card requests IRQ. This is the default setting and should not be changed unless the VGA card manufacturer requires Palette Snooping to be Enabled. Enabled: informs the PCI devices that an ISA graphics device is installed in the system so the card will function correctly.
PAGE 75
3.9 - Boot Menu You can display Boot Setup option by highlighting it using the Arrow (Ç/È) keys and pressing Enter. The settings are described on the following pages. Main Advanced Boot Settings BIOS Setup Utility PCI/PnP Boot Security Chipset Exit Configures settings during System Boot. Boot Settings Configuration ← → Select Screen ↑↓ Select Item Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit Boot Device Priority Hard Disk Drives 3.9.
PAGE 76
Feature Option Description Boot Settings Configuration Quick Boot Enabled Disabled Disabled Quiet Boot Enabled Add On ROM Display Mode Boot up Num-Lock PS/2 Mouse Support Wait for ‘F1’ If Error Hit ‘DEL’ Message Display PXE feature Interrupt 19 Capture Endless Boot Force BIOS Keep Current On Off Enabled Disabled Auto Enabled Disabled Enabled Disabled Enabled Disabled Enabled Disabled Disabled Enabled This option allows user bypass BIOS self test during POST. Disabled: displays normal POST messages.
PAGE 77
3.9.2 - Boot Device Priority Use this screen to select options for the Boot Device Priority. Use the up and down arrow (Ç/È) keys to select an item. Use the Plus and Minus (+/-) keys to change the value of the selected option. Main Advanced BIOS Setup Utility PCI/PnP Boot Security Boot Device Priority 1st Boot Device 2nd Boot Device 3rd Boot Device [xx,xxx-xxxxx:xxx] [xx,xxx-xxxxx:xxx] [xx,xxx-xxxxx:xxx] Chipset Exit Specifies the boot sequence from the available devices.
PAGE 78
3.9.3 - Hard Disk Drives Use this screen to select options for the Hard Disk Drives. Use the up and down arrow (Ç/È) keys to select an item. Use the Plus and Minus (+/-) keys to change the value of the selected option. Main Advanced BIOS Setup Utility PCI/PnP Boot Security Hard Disk Drives 1st Drive [xxxxxxxx] Chipset Exit Specifies the boot sequence from the available devices.
PAGE 79
3.10 - Security Menu The system can be configured so that all users must enter a password every time the system boots or when BIOS Setup is entered, using either the Supervisor password or User password. The Supervisor and User passwords activate two different levels of password security. If you select password support, you are prompted for a one to six character password. Type the password on the keyboard. The password does not appear on the screen when typed. Make sure you write it down.
PAGE 80
3.11 - Chipset Menu This menu allows the user to customize functions of the Intel Chipsets. Select a menu by highlighting it using the Arrow (Ç/È) keys and pressing Enter. The settings are described on the following pages. Main Advanced BIOS Setup Utility PCI/PnP Boot Security Advanced Chipset Settings WARNING: Setting wrong values in below sections may cause system to malfunction. CPU Bridge Configuration Northbridge Configuration Southbridge Configuration 80 http://www.TYAN.
PAGE 81
3.11.1 - CPU Bridge Configuration Sub- Menu BIOS Setup Utility Main Advanced PCI/PnP Boot Security Chipset Exit Transition the links to CPU Bridge Chipset Configuration the specified speed CPU Revision :B0 when transitioning the Current QPI Frequency :x.xxxGT links to full-speed.
PAGE 82
Feature Option CPU Bridge Chipset Configuration Auto 4.800GT QPI Frequency 5.866GT Memory Frequency 6.400GT Auto Force DDR-800 Force DDR-1066 Force DDR-1333 Independent Channel Mirroring Lockstep Memory Mode Sparing Demand Scrubbing Patrol Scrubbing Disabled Enabled Disabled Enabled Throttling-Closed Loop Disabled Hyster temp Disabled 1.
PAGE 83
Feature Altitude Option Sea Level or Below 1~300 301~600 601~900 901~1200 1201~1500 1501~1800 1801~2100 2101~2400 2401~2700 2701~3000 DIMM Pitch Throttling-Open Loop Enabled Disabled Inlet temp [070] Temp Rise [020] Description The system altitude above sea level(in meters) The pitch between DIMMs.(in units of 1/1000 inch) BIOS to program Open Loop throttling for memory compents. Temperature at the chassis inlet.(in 0.5℃ units) Temperature rise to the DIMM thermal zone. (in 0.
PAGE 84
3.11.2 - Northbridge Configuration Sub-Menu This menu gives options for northbridge devices settings. Select a menu by highlighting it using the Arrow (Ç/È) keys and pressing Enter. The settings are described on the following pages. Main Advanced BIOS Setup Utility PCI/PnP Boot Security NorthBridge Chipset Configuration NB Revision Current CSI Frequency [B0] X.
PAGE 85
3.11.3 - Southbridge Configuration Sub-Menu This menu gives options for southbridge devices settings. Select a menu by highlighting it using the Arrow (Ç/È) keys and pressing Enter. The settings are described on the following pages. BIOS Setup Utility Main Advanced PCI/PnP Boot Security Chipset Options South Bridge Chipset Configuration Disabled HAD Controller [Enabled] 2 USB Ports SMBUS Controller [Enabled] 4 USB Ports SLP_S4# Min.
PAGE 86
3.12 - Exit Menu You can display an Exit BIOS Setup option by highlighting it Arrow (Ç/È) keys and pressing Enter. Main Advanced BIOS Setup Utility PCI/PnP Boot Security Chipset Exit Exit Options Exit system setup after saving the changes. Save Changes and Exit Discard Changes and Exit Discard Charges F10 key can be used for this operation.
PAGE 87
Chapter 4: Diagnostics If you experience problems with setting up your system, always check the following things in the following order: Memory, Video, CPU By checking these items, you will most likely find out what the problem might have been when setting up your system. For more information on troubleshooting, check the TYAN® website at: http://www.TYAN.com. 4.1 - Beep Codes Fatal errors, which halt the boot process, are communicated through two kinds of audible beeps.
PAGE 88
4.3 - AMIBIOS Post Code The POST code checkpoints are the largest set of checkpoints during the BIOS pre-boot process. The following table describes the type of checkpoints that may occur during the POST portion of the BIOS: Checkpoint 03 04 05 06 08 0A 0B 0C 0E 13 24 30 2A 2C 2E 31 33 37 Description Disable NMI, Parity, video for EGA, and DMA controllers. Initialize BIOS, POST, Runtime data area. Also initialize BIOS modules on POST entry and GPNV area.
PAGE 89
Checkpoint 38 39 3A 3B 3C 40 50 52 60 75 78 7A 7C 84 85 87 8C 8E 90 A0 A1 A2 A4 A7 A8 A9 AA AB AC B1 00 Description Initializes different devices through DIM. See DIM Code Checkpoints section of document for more information. Initializes DMAC-1 & DMAC-2. Initialize RTC date/time. Test for total memory installed in the system. Also, Check for DEL or ESC keys to limit memory test. Display total memory in the system. Mid POST initialization of chipset registers.
PAGE 90
http://www.TYAN.
PAGE 91
Appendix: How to Make a Driver Diskette Follow the steps below to make a driver diskette from the TYAN® driver CD provided. 1. Start the system and insert the TYAN® CD into the CD-ROM drive to boot from CD. You will see the following menu. Then press [1] and [Enter] to boot the system to TYAN® diskette maker. (If you would like to boot from hard disk, press 0 and Enter or just wait for 10 seconds to boot automatically from hard disk.). Boot from CD: ISOLINUX 2.00 2002-10-25 Copyright (C) 1994-2002 H.
PAGE 92
3. The following picture pops up after selecting the chipset model. TYAN Driver Diskette Maker ** nVidia ** ====Choose Chipset Model==== 01 nVidia NVRAID EXIT 4. After selecting the chipset model, select the OS to start the diskette making. TYAN Driver Diskette Maker ====Example Chipset Driver==== Diskette Diskette Diskette Diskette =01= =02= =03= =04= Microsoft Windows 2000 32-bit Microsoft Windows XP 32-bit Microsoft Windows XP 64bit Microsoft Windows 2003 64-bit Back 5.
PAGE 93
Glossary ACPI (Advanced Configuration and Power Interface): a power management specification that allows the operating system to control the amount of power distributed to the computer’s devices. Devices not in use can be turned off, reducing unnecessary power expenditure. AGP (Accelerated Graphics Port): a PCI-based interface which was designed specifically for demands of 3D graphics applications. The 32-bit AGP channel directly links the graphics controller to the main memory.
PAGE 94
losing your data should the system crash. Information in a buffer is temporarily stored, not permanently saved. Bus: a data pathway. The term is used especially to refer to the connection between the processor and system memory, and between the processor and PCI or ISA local buses. Bus mastering: allows peripheral devices and IDEs to access the system memory without going through the CPU (similar to DMA channels). Cache: a temporary storage area for data that will be needed often by an application.
PAGE 95
DRAM (Dynamic RAM): widely available, very affordable form of RAM which looses data if it is not recharged regularly (every few milliseconds). This refresh requirement makes DRAM three to ten times slower than non-recharged RAM such as SRAM. ECC (Error Correction Code or Error Checking and Correcting): allows data to be checked for errors during run-time. Errors can subsequently be corrected at the same time that they’re found.
PAGE 96
I/O (Input/Output): the connection between your computer and another piece of hardware (mouse, keyboard, etc.) IRQ (Interrupt Request): an electronic request that runs from a hardware device to the CPU. The interrupt controller assigns priorities to incoming requests and delivers them to the CPU. It is important that there is only one device hooked up to each IRQ line; doubling up devices on IRQ lines can lock up your system. Plug-n-Play operating systems can take care of these details for you.
PAGE 97
designed to define a standard set of preboot protocol services within a client with the goal of allowing networked-based booting to boot using industry standard protocols. RAID (Redundant Array of Independent Disks): a way for the same data to be stored in different places on many hard drives. By using this method, the data is stored redundantly and multiple hard drives will appear as a single drive to the operating system.
PAGE 98
advantage of the increased bandwidth of the PCI Express bus architecture, and features hardware and software innovations within NVIDIA GPUs (graphics processing units) and NVIDIA MCPs (media and communications processors). Depending on the application, NVIDIA SLI can deliver as much as two times the performance of a single GPU configuration. Standby mode: in this mode, the video and hard drives shut down; all other devices continue to operate normally.
PAGE 99
Technical Support If a problem arises with your system, you should first turn to your dealer for direct support. Your system has most likely been configured or designed by them and they should have the best idea of what hardware and software your system contains. Hence, they should be of the most assistance for you.
PAGE 100
Note: A receipt or copy of your invoice marked with the date of purchase is required before any warranty service can be rendered. You may obtain service by calling the manufacturer for a Return Merchandise Authorization (RMA) number.The RMA number Should be prominently displayed on the outside of the shipping carton and the package should be mailed prepaid. TYAN® will pay to have the board shipped back to you.