User guide

ManualsBrandsTweco ManualsEquipment170Pi Transtig

Table Of Contents

0-5143-CCr
SECTION 1: ARC WELDING SAFETY INSTRUCTIONS AND WARNINGS
- 1.01 Arc Welding Hazards
- 1.02 Principal Safety Standards
- 1.03 Declaration of Conformity
SECTION 2: INTRODUCTION
- 2.01 How To Use This Manual
- 2.02 Equipment Identification
- 2.03 Receipt Of Equipment
- 2.04 Symbol Chart
- 2.05 Description
- 2.06 User Responsibility
- 2.07 Transporting Methods
- 2.08 Packaged Items
- 2.09 Duty Cycle
- 2.10 Specifications
- 2.11 Options and Accessories
SECTION 3: INSTALLATION, OPERATION AND SETUP
- 3.01 Environment
- 3.02 Location
- 3.03 Ventilation
- 3.04 Mains Supply Voltage Requirements
- 3.05 Electromagnetic Compatibility
- 3.06 Transtig 170Pi Power Source Controls, Indicators and Features
- 3.07 Shielding Gas Regulator Operating Instructions
- 3.08 Setup for TIG (GTAW) Welding
- 3.09 Foot Control Part No. W4015800 (Optional Accessory)
- 3.10 Setup for Manual Arc (MMAW) Welding
SECTION 4: BASIC WELDING GUIDE
- 4.01 Stick (MMAW) Basic Welding Technique
- 4.02 Stick (MMAW) Welding Troubleshooting
- 4.03 TIG (GTAW) Basic Welding Technique
- 4.04 TIG (GTAW) Welding Problems
SECTION 5: POWER SOURCE PROBLEMS AND ROUTINE SERVICE REQUIREMENTS
- 5.01 Power Source Problems
- 5.02 Routine Service and Calibration Requirements
- 5.03 Cleaning the Welding Power Source
SECTION 6: KEY SPARE PARTS
- 6.01 Power Source
- 6.02 Tig Torch W4014604
APPENDIX: TRANSTIG 170Pi CIRCUIT DIAGRAM
CIGWELD - LIMITED WARRANTY TERMS
TERMS OF WARRANTY – January 2013
WARRANTY SCHEDULE – January 2013
GLOBAL CUSTOMER SERVICE CONTACT INFORMATION
SECTION 1: ARC WELDING SAFETY INSTRUCTIONS AND WARNINGS
- 1.01 Arc Welding Hazards
- 1.02 Principal Safety Standards
- 1.03 Declaration of Conformity
SECTION 2: INTRODUCTION
- 2.01 How To Use This Manual
- 2.02 Equipment Identification
- 2.03 Receipt Of Equipment
- 2.04 Symbol Chart
- 2.05 Description
- 2.06 User Responsibility
- 2.07 Transporting Methods
- 2.08 Packaged Items
- 2.09 Duty Cycle
- 2.10 Specifications
- 2.11 Options and Accessories
SECTION 3: INSTALLATION, OPERATION AND SETUP
- 3.01 Environment
- 3.02 Location
- 3.03 Ventilation
- 3.04 Mains Supply Voltage Requirements
- 3.05 Electromagnetic Compatibility
- 3.06 Transmig 175i Power Source Controls, Indicators and Features
- 3.14 Shielding Gas Regulator Operating Instructions
- 3.17 Setup for TIG (GTAW) Welding
- 3.18 Setup for Manual Arc (MMAW) Welding
SECTION 4: BASIC WELDING GUIDE
- 4.03 Stick (MMAW) Basic Welding Technique
- 4.04 Stick (MMAW) Welding Troubleshooting
- 4.05 TIG (GTAW) Basic Welding Technique
- 4.06 TIG (GTAW) Welding Problems
SECTION 5: POWER SOURCE PROBLEMS AND ROUTINE SERVICE REQUIREMENTS
- 5.01 Power Source Problems
- 5.02 Routine Service and Calibration Requirements
- 5.03 Cleaning the Welding Power Source
AP0-5143-APENDIX
CIGWELD - LIMITED WARRANTY TERMS
TERMS OF WARRANTY - JULY 2010
WARRANTY SCHEDULE - JULY 2010
GLOBAL CUSTOMER SERVICE CONTACT INFORMATION

TRANSTIG 170Pi

Manual 0-5241 A-1 APPENDIX

APPENDIX: TRANSTIG 170Pi CIRCUIT DIAGRAM

Q1

T14

A

N

E

EMC

FILTER

R39

CY1

POSITIVE

NEGATIVE

24VDC FAN

C20

Q2

T1

R100, 102

C100

NEGATIVE

POSITIVE

HALL

CT2

MAIN CONTROL BOARD

WELDING TERMINALS

SW1

C17

R56 C21

C19

T18

R101, 103

C101

V8

COUT2

COUT1

L1

DISPLAY BOARD

MB

J12

SOLENOID

8 PIN REMOTE

OT1

TH1

WV

WELD POSITIVE

WELD NEGATIVE

CT1

INPUT

RECTIFIER

POSITIVE

NEGATIVE

R2

4R 50W

J1

V7

L4

C23

C22

DRIVE

IN

QF

SOURCE

DY2

DY

DY1

PFC

JC

GUN

GUN OUT

FJ OT2

IFB

TORCH TRIGGER

C25

C24

EFFECT

T2

HF COIL

110/220V

ACTIVE

NEUTRAL

NEUTRAL

ACTIVE

HF 220V

SOU HF

HF

GUN IN

FILTER

HF BOARD

A-11670