Manual

ULTRA-CUT 100 XT
4-18 OPERATION Manual 0-5303
CCM Status Code
Group 2 -- Plasma Power Supply
Code Message Remedy / Comments
201 Missing AC Phase
Blownwallfuse,BlownunitfuseF1orF2orrearpanel,Badpowercableconnection;
Defective System Bias PCB.
202 Not used Reserved for legacy product
203 Not used Reserved for legacy product
204 Not used Reserved for legacy product
205 DC Output Low
Lessthan60VDC;Negativeleadshorttoworkorground;Defectiveinverter(out-
putshorted);CCMvoltagesense(J24)disconnectedorwirebroken;DefectiveCCM.
206 Not used Reserved for legacy product
207
Unexpected current in
work lead
Current above 8A in work lead prior to pilot ignition or transfer. Negative lead short
togroundorarcstarterchassis;DefectiveHCT1workleadcurrentsensor;Defec-
tive Relay PCB.
208
Unexpected current in
pilot circuit
Current above 6A in pilot circuit prior to ignition. Wrong or mismatched consum-
ablescausingtip-electrodeshort;Pilotleadshortedtonegativeintorchtube;
DefectiveRelayPCB;DefectivePilotPCB;Possibleshortedtorch.
209 Not used Reserved for legacy product
210
Work Current Too
High
Work lead current detected greater than 16% above process setting. Possible defec-
tiveHCT1WorkleadcurrentsensororRelayPCB;DefectiveCCM.
211 Work Current Too Low
Work current detected more than 16% below process setting. Possible defec-
tiveHCT1WorkleadcurrentsensororRelayPCB;PossibledefectivepilotPCB
(shortedIGBT);
212
Inverter 1A Output
Current Low
Plasma work current low during cutting and attributed to Inverter Module 1 Sec-
tionAoutputlow;Inverteroutputdisconnected;Possibledefectiveribboncable;If
problem persists replace Inverter Module 1
213
Inverter 1B Output
Current Low
Plasma work current low during cutting and attributed to Inverter Module 1 Sec-
tionBoutputlow;Inverteroutputdisconnected;Possibledefectiveribboncable;If
problem persists replace Inverter Module 1
214
Inverter 2A Output
Current Low
Plasma work current low during cutting and attributed to Inverter Module 2 Section
Aoutputlow;Inverteroutputdisconnected;Possibledefectiveribboncable;If
problem persists replace Inverter Module 2
215
Inverter 2B Output
Current Low
Plasma work current low during cutting and attributed to Inverter Module 2 Section
Boutputlow;Inverteroutputdisconnected;Possibledefectiveribboncable;If
problem persists replace Inverter Module 2
216
Inverter 3A Output
Current Low
Plasma work current low during cutting and attributed to Inverter Module 3 Section
Aoutputlow;Inverteroutputdisconnected;Possibledefectiveribboncable;If
problem persists replace Inverter Module 3
217
Inverter 3B Output
Current Low
Plasma work current low during cutting and attributed to Inverter Module 3 Section
Boutputlow;Inverteroutputdisconnected;Possibledefectiveribboncable;If
problem persists replace Inverter Module 2
218
Inverter 1A Output
Current High
Plasma work current high during cutting and attributed to Inverter Module 1 Section
Aoutputhigh;IfproblempersistsreplaceInverterModule1
219
Inverter 1B Output
Current High
Plasma work current high during cutting and attributed to Inverter Module 1 Section
Boutputhigh;IfproblempersistsreplaceInverterModule1
220
Inverter 2A Output
Current High
Plasma work current high during cutting and attributed to Inverter Module 2 Section
Aoutputhigh;IfproblempersistsreplaceInverterModule2
221
Inverter 2B Output
Current High
Plasma work current high during cutting and attributed to Inverter Module 2 Section
Boutputhigh;IfproblempersistsreplaceInverterModule2