User Manual

8 Multi Format LCD Monitor Multi Format LCD Monitor 9
3. Controls & Functions 3. Controls & Functions
FRONT FRONT
• [SDI-A] Button/Lamp
- Used to select SDI-A input.
• [SDI-B] Button/Lamp
- Used to select SDI-B input.
• [HDMI] Button/Lamp
- Used to select HDMI input.
• [ANALOG] Button/Lamp
- Used to select desired Analog input.
(CVB1/2/3, S-Video, Component, RGB)
- Press the button to activate the analog input
menu-selection, then use UP and DOWN
button to select desired input.
* See section “Other Functions [1]ANALOG
Button” for more information.
• [SCAN] Button/Lamp
- Used to change the scan mode.
- Press the button to activate through the scan
modes: [UNDERSCAN] -> [OVERSCAN] ->
[PIXEL TO PIXEL] -> [USER ASPECT] ->
[UNDERSCAN]
#PIXEL TO PIXEL mode is not available in
graphic mode.
#[USER ASPECT]: User can adjust width and
height of the display.
* See section “7. Other Functions -> [1] Pixel to
Pixel and [2] User Aspect” for more
information.
• [ASPECT] Button/Lamp
- Used to change the display variout ratio.
- Activates in order of [16:9]-[4:3]-[2.35:1]-[1.85:1]
- [15:9]-[16:10]-[AUTO]-[16:9].
• [F1][F2][F3][F4] Button/Lamp
- Used to activate the function.
* See section “6.Button Functions -> [4]
Function key set button” for more
information.
• [MARKER] Button/Lamp
- Used to activate/deactivate the Marker. The
type of marker at work may be selected on
the main menu.
• [H/V DELAY] Button/Lamp
- Used to check horizontal sync and vertical
sync simultaneously by moving the display
to the left, right, up and down.
- In this mode, the brightness of image
automatically increase for easy verication of
synchronized signals.
• [BLUE ONLY]/[MONO] Button/Lamp
- Activates in the order of [OFF]-[Blue Only]-
[Mono]-[OFF].
- Press the button to remove red and green
from the input signal and display the screen
only under a blue signal. Press the button
again to activate mono mode.
- They are not available in RGB, DVI ANALOG,
DVI DIGITAL and HDMI modes.
• [MAX BRIGHT] Button/Lamp
- Used to activate the MAX BRIGHT.
• [WAVEFORM]/[VECTOR SCOPE] Button/Lamp
- Used to activate/deactivate the Waveform.
- The type of waveform at work may be
selected on the [Waveform] menu.
• [MENU/EXIT] Button/Lamp
- Used to activate the OSD menu.
- When the OSD menu is activated, press this
button to exit from the menu.
• [MENU/EXIT] Button/Lamp
- Used to activate the OSD menu.
- When the OSD menu is activated, press this
button to exit from the menu.
• [OPERATE] Lamp
- Indicates condition and power status of unit.
- Light turns o when the power is disconnected.
- Standby mode is indicated by a red LED light.
- Normal (active) mode is indicated by a Green
LED light.
- Restores to previous state when monitor
power turns o and comes back on.
• [POWER] Button
- Used to turn power on and o.
• AUDIO OUT (Phone Jack)
- Used for Stereo Audio Output through Phone
Jack. (video signals with embedded audio only)
• PGM (USB)
- This terminal is used to upgrade the rmware
or color calibration made by TVLogic.
• [TALLY] Lamp
- Tally lamp that can be toggled in green or red
using the REMOTE(RJ-45), LAN port.
• [BRIGHT] Knob
- Used to adjust the degree of brightness.
- The value is selectable between -100 ~ 100.
• [CONTRAST] Knob
- Used to adjust the contrast.
- The value is selectable between -100 ~ 100.
• [F5/VOLUME] Knob
- Used to adjust the volume for internal speaker
and external output.
- The value is selectable between 0 ~ 30.
- [F5] : Press F5 Knob for 2 second to set the
function. Available functions are [VOLUME]-
[CHROMA]-[APERTURE]-[PHASE]-[FOCUS
L E V E L ] .
• [UP/DOWN/ENTER] Knob
- Used to move within the menu when OSD
menu is activated, and is also used to
decrease or increase the value of the selected
feature.
- Press the knob to select the main menu and
sub menus.