7” FHD Multi Format Broadcast LCD Monitor Operation Manual_v1.
Contents 1. Caution ........................................................................... 2. Main Features ................................................................... 3. Controls & Functions ........................................................... 4. Menu Organization & Adjustment ........................................... 5. Menu Operations ............................................................... [1] PICTURE ......................................................................
1. Caution • Always use set voltage. (DC 12V) • When using a DC Adapter other than the one supplied by the manufacturer, please be advised that the adapter with DC 12V/3A ~ 6A can be compatible with the monitor. • All operating instructions must be read and understood before the product is operated. • These safety and operating instructions must be kept in safe place for future reference. • All warnings on the product and in the instructions must be observed closely.
3. Controls & Functions 2. Main Features LVM-075A Monitor contains the following features: • Compatible with various analog signals - This product is compatible with various analog signals such as CVBS(Composite), S-Video and YPbPr(Component). • HDMI(with HDCP) Signal - HDMI(w/ HDCP) input is available without any other accessory. • HDMI To HDMI Throughout - This product features an HDMI To HDMI Throughout. • HDMI To SDI Conversion Output - This product features an HDMI To SDI conversion output.
3. Controls & Functions 3. Controls & Functions FRONT • [SDI-A] Button/Lamp - Used to select SDI-A input. • [SDI-B] Button/Lamp - Used to select SDI-B input. • [HDMI] Button/Lamp - Used to select HDMI input. • [ANALOG] Button/Lamp - Used to select desired Analog input. (CVB1/2/3, S-Video, Component, RGB) - Press the button to activate the analog input menu-selection, then use UP and DOWN button to select desired input. * See section “Other Functions [1]ANALOG Button” for more information.
3. Controls & Functions 4. Menu Tree & Adjustment REAR [1] Menu Tree • EXT.TALLY IN • LAN • OSD(On-Screen Display) Menu helps you use various functions. • [TALLY] Lamp • [RS422 IN/OUT] (RJ-45) • This Picture is the menu structure for LVM075A - This terminal uesd to External tally input. - Tally lamp that can be toggled in green or red using the REMOTE(RJ-45), LAN port. • [SDI-IN A] (BNC) - HD/SD SDI signal input terminal for SDI A.
5. Menu Operations 5. Menu Operations [1] Picture [2] Color • Aperture • Temp. Adaptive Color - Used to set the sharpness level from -5 to 19. # Press the Knob to adjust Aperture quickly. - [On] : Used to measure and compensate the color temperature shift caused by panel temperature variation. - [Off] : Used to apply preset color temperature setting regardless of the panel temaperature. • NTSC Setup - Used to set Black Level of NTSC video as 0(zero setup) or 7.5 IRE.
5. Menu Operations 5. Menu Operations [3] Marker [4] GPI / UMD • The selectable values are as follows : Menu Classification • Marker • Marker Mat • Center Marker • Marker Color - Used to activate the Marker function. - Available marker types are OFF, 16:9, 4:3, 4:3 ON AIR, 15:9, 14:9, 13:9, 1.85:1, 2.35:1, 1.85:1 & 4:3 and USER. - Displays the Center Marker on the screen. • Safety Area - Used to select to display and controls the size and availability of the Safety Area.
5. Menu Operations 5. Menu Operations [4] GPI / UMD [4] GPI / UMD • UMD Character • XLR TALLY On/Off - Customizes the characters for Under Monitor Display. - Alphabets, numbers and special symbols are available. - Maximum of 8 characters are available. - Used to set Tally operation according to the input level of TALLY IN terminal which is among the terminals of XLR 4P connector in the rear. • XLR TALLY Operating Level • UMD CHARACTER COLOR - Used to set the color of UMD character.
5. Menu Operations 5. Menu Operations [4] GPI / UMD [4] GPI / UMD • Tally Type - Default - S-8C(Single 8 Character) & S-16C(Single 16 Character) * Transmission (18 Byte) (PC or Device -> Monitor) HEADER (1 BYTE) CONTROL BYTE(1 BYTE) DISPLAY DATA (16 BYTE) * [HEADER] : Display address (0~126) + 80 hex.
5. Menu Operations [4] GPI / UMD 5. Menu Operations [5] Waveform [5] Waveform • Waveform Trans - Controls the transparency level of the WAVEFORM/VECTOR. - Available values are OPAQUE and TRANS. * If the option is set to OPAQUE, the main OSD will overlap with the waveform/vector. However, it will automatically display it as transparent and goes back to opaque if the main OSD disappears.
5. Menu Operations 5. Menu Operations [5] Waveform [6] Audio • C Min * 8 CH Side : Displays 8 channels on top right of the screen vertically. * 4 CH : Displays 2 channels on top left and 4 channels on top right of the screen horizontally. * 4 CH Side : Displays 4 channels on top right of the screen vertically. - Used to set the minimum chroma(C’) level from 0 to 255. - Pixels with values exceeding the min C’ level will blink in the screen, and displayed as red on the Waveform.
5. Menu Operations 5. Menu Operations [7] Display & Set [7] Display & Set • 3G Format • Closed Caption - Used to select 3G-SDI A/B input format among NORMAL MODE(AUTO - A 422 10BIT_ YCbCr 50/60P), A 444 10/12BIT_YCbCr, A 444 10/12BIT_RGB, A 422 12BIT_YCbCr, B 444 10/12BIT_YCbCr, B 444 10/12BIT_RGB, B 422 12BIT_YCbCr, B 422 10BIT_YCbCr 50/60P. - In NORMAL MODE, automatically detected when Payload signal is contained. - This item selects Closed Caption.
5. Menu Operations [7] Display & Set 6. Button Functions [1] Analog Button • This product is capable of processing all input signals usable in ANALOG mode. • The Analog input settings are as follows: 1. Press the ANALOG button on the front of the product and activate the menu below : [2] SDI Button • LVM-075A unit is capable of processing dual SDI Input signal. 1. Press [SDI] button on the front of the monitor and activate the OSD menu as shown on the below. 2.
6. Button Functions [4] Function Key Set Button • Used to make a quick setting of the Function Key. 1. Press the function button(F1~F4) on the front of the monitor for more than 2 seconds and activate the OSD menu as follows. DOWN UP DOWN UP DOWN DOWN • This product supports various scan modes. • Press [SCAN] button on the front of the monitor to activate different scan modes.
7. Other Functions 7. Other Functions [2] User Aspect [3] Waveform / Vectorscope • Waveform Y - Displays the Luma(Y’) component of the input signal into waveform. • Select [Aspect] mode in the OSD menu to activate the[User Aspect] mode. • VectorScope - Displays the color components ‘B-Y’ and ‘R-Y’ of the input signals onto the X-Y axis. - Two different types of Vetorscopes are displayed according to SD or HD input signals. - 100% and 75% scales are indicated on the Vetorscope.
7. Other Functions [4] Line Select (Waveform/VectorScope) • Used to select specific Vertical Line for 7. Other Functions [6] Luma(Y’) Zone Check [5] Zoom WaveForm/VectorScope. • Used to magnify the input signal from 0% to 90%. - It is available when LINE WaveForm is activated. • Supports Zoom Width Scroll / Zoom Height Scroll function. - To activate this feature, go to [Waveform][Select Line Position] and use the Knob to select a vertical line.
7. Other Functions [7] Focus Assist • Focus Assist function assigns a color to the pixels in the shape or boundary area of the image to inform the user to make the best focus. - With this function, user can easily differenciate the focused area from out-focused area especially shooting with shallow depth of field. - Available types are [Mono] and [Color] types. * [Mono] : Background image is mono type. [Color] : Background image is original color type. 7.
7. Other Functions [10] HDMI To SDI Conversion-Out • Video source from ‘HDMI input’ terminal can be output through ‘SDI throughout’ terminal. ※Note: HDSLR camera manufacturers usually specify the resolution and frame rate for the recording. The signal format that is output through HDMI terminal of cameras may differ from makers to makers. The signal format for HDMI output and playback function of Canon HDSLRs is 59.94i.
9. Product Specifications 10. Optional Accessories LVM-075A LCD Input Connector Output Input Signal Analog Input Spec Size 7” Resolution 1920 X 1080 (16:9) Pixel Pitch 0.018(H) X 0.018(W) mm Color Depth 16.7M (True 8bit) Viewing Angle H : 170 degrees / V : 170 degrees Luminance of white 600 cd/ m2 (Center) Contrast Ratio 800 : 1 Display Area 155.52(H) X 87.
MEMO 40 Multi Format LCD Monitor MEMO Multi Format LCD Monitor 41
MEMO 42 Multi Format LCD Monitor
FOR MORE INFORMATION PLEASE VISIT : http://www.tvlogic.tv 12F, ACE HIGH-END 8, 84, Gasan digital 1-ro, Geumcheon-gu, Seoul, 08590, KOREA 부사장 TEL : +82-70-8668-6611, FAX : 82-2-6123-3201, E-mail : sales@ t vlogic.co.kr 153-802 서울특별시 금천구 가산동 345-4 조 성 일 Mobile.
