7” FHD High Bright Field Monitor Operation Manual_ver 1.
1. Caution ...................................................................................... 2. Main Features ............................................................................ 3. Controls & Functions ................................................................... 4. Menu Tree & Adjustment ............................................................. 5. Menu Operations ........................................................................ [1] Picture ....................................
1. Caution • Always use set voltage. (DC 6.8~12V) • When using a DC Adapter other than the one supplied by the manufacturer, please be advised that the adapter with DC 12V/3A ~ 6A can be compatible with the monitor. FHD High Bright Field Monitor 4 • All operating instructions must be read and understood before the product is operated. • These safety and operating instructions must be kept in safe place for future reference.
1. Caution • Unplug the power cord from the DC outlet before cleaning the product. Use a damp cloth to clean the product. Do not use liquid cleaners or aerosol cleaners. • Unplug the power cord from the AC outlet if you do not use the product for considerably long time. • Do not use the product near water, such as bathtub, washbasin, kitchen sink and laundry tub, swimming pool and in a wet basement. • Keep the product away from direct rays of the Sun-light.
2. Main Features F-7H Monitor contains the following features : FHD High Bright Field Monitor 6 • Compatible with various SDI signals formats (SD/HD/3G) - This product is compatible with various SDI signals - 480i, 576i, 720p, 1080i, 1080p, 1080psf • HDMI(with HDCP) Signal - This product is compatible with various HDMI signals.
3.
3. Controls & Functions TOP FHD High Bright Field Monitor 8 • [MENU/EXIT/SOURCE] Button - Used to activate the OSD menu. - When the OSD menu is activated, press this button to exit from the menu. - Press the button for more than 2 seconds to activate Input Select menu. (SDI, HDMI) - Use the [ENCODER] Knob to change the Input Signal. • [UP/DOWN/ENTER] Knob - Used to move within the menu when OSD menu is activated, and is also used to decrease or increase the value of the selected feature.
3. Controls & Functions REAR • [HDMI IN] - Signal input terminal for HDMI signal. • [REAR TALLY] - Activates same as [SCREEN TALLY]. • [HDMI OUT] - Signal output terminal for HDMI signal. - Video source from SDI input terminal can be converted to HDMI format. • [DC POWER / TALLY] (XLR 4P) - Tally Signal In Level DC5V ±2V - Battery Power Input terminal for DC 12V - Rated Power Input : DC 12V (1.
4. Menu Tree & Adjustment [1] Menu Tree [3] Menu Control Sequence • OSD(On-Screen Display) Menu helps to use varous different functions. • This Picture is the menu structure for F-7H. FHD High Bright Field Monitor 10 PICTURE 같이 BRIGHT CONTRAST CHROMA APERTURE KNOB LOCK F-7H +90 +90 +90 +90 UNLOCK [2] Menu Control • User may control various functions using the MENU button and the Knob on the top of the monitor. • Menu control sequence follows the order below. 1.
5. Menu Operations [1] PICTURE F-7H +90 +90 +90 +90 UNLOCK REC 709 SYNCHRONIZATION NONE01 NONE01 NONE01 • BRIGHTNESS - Used to set the brightness(=offset) level from -100 to 100. # Brightness can be adjusted by using the Knob on the top of the monitor. • CONTRAST - Used to set the contrast(gain) level from -100 to 100. # Contrast can be adjusted by using the Knob on the top of the monitor. • CHROMA - Used to set the saturation level from -50 to 50.
5. Menu Operations [2] COLOR FHD High Bright Field Monitor 12 COLOR같이 STANDARD VIDEO RANGE PEAK LUMINANCE BLACK LEVEL COLOR GAMUT COLOR TEMP EOTF LOCAL DIMMING EETF HLG SG SG CAM LUT CAM LUT THR F-7H UHD NARROW 100 0.001 BT.2020 6500K 2.4 OFF OFF OFF OFF OFF PAGE (1/2) • STANDARD - Used to select the color and dynamic rage of the screen. - Available options are HD, UHD, DCI-P3, PQ, HLG, SLog3 and User1/2/3. # Activates only in the User1/2/3 mode.
5. Menu Operations [2] COLOR STANDARD VIDEO RANGE PEAK LUMINANCE BLACK LEVEL COLOR GAMUT COLOR TEMP EOTF LOCAL DIMMING EETF HLG SG SG CAM LUT CAM LUT THR F-7H UHD NARROW 100 0.001 BT.2020 6500K 2.4 OFF OFF OFF • SG (System Gamma) - The System Gamma of HLG is automatically calculated and displayed according to the set peak luminance. - Activates only when the EOTF is set to HLG and the HLG SG is Auto. • CAM LUT - Used to change the Camera LUT.
5. Menu Operations [2] COLOR COLOR같이 FHD High Bright Field Monitor 14 TEMP COLOR GAIN RED GAIN GREEN GAIN BLUE BIAS RED BIAS GREEN BIAS BLUE COLOR COPY COLOR SPACE F-7H 6500K_60P +90 +90 +90 +90 +90 +90 6500K_60P BT.709 PAGE (2/2) • TEMP COLOR - Controls the color temperature and allows instant access to preset the color temperature settings. - Available color temperatures are 6500K, 9300K and User1/2/3.
5. Menu Operations [3] MARKER ENABLE MARKER CENTER MARKER SAFETY AREA FIT MARKER MARKER MAT MARKER COLOR THICKNESS USER MARKER H1 USER MARKER H2 USER MARKER V1 USER MARKER V2 F-7H ON OFF OFF OFF OFF OFF WHITE 2 + 0 +1920 + 0 +1080 • ENABLE - Used to activate the Marker function. • MARKER - Available Marker types are OFF, 16:9, 4:3, 4:3 ON AIR, 15:9, 14:9, 13:9, 1.85:1, 2.35:1, 1.85:1 & 4:3 and USER. • CENTER MARKER - Displays the Center Marker on the screen.
5. Menu Operations [3] MARKER FHD High Bright Field Monitor 16 MARKER같이 ENABLE MARKER CENTER MARKER SAFETY AREA FIT MARKER MARKER MAT MARKER COLOR THICKNESS USER MARKER H1 USER MARKER H2 USER MARKER V1 USER MARKER V2 F-7H ON OFF OFF OFF OFF OFF WHITE 2 + 0 +1920 + 0 +1080 • USER MARKER H1 - Used to set the position of the first horizontal marker line. - Displayed when the MARKER menu is set to USER. • USER MARKER H2 - Used to set the position of the second horizontal marker line.
5. Menu Operations [4] VIDEO F-7H SCAN ZERO SCAN ASPECT 16:9 H/V DELAY OFF BLUE ONLY OFF USER ASPECT HOR USER ASPECT VER 3G FORMAT NORMAL H/V FLIP OFF ZOOM OFF ZOOM SPLIT OFF + + 0 0 PAGE (1/2) • SCAN - Used to change the Scan mode. Scroll up and down using the Knob and the mode will chang as the following sequence. [Zero Scan] -> [Over Scan] -> [Pixel-To-Pixel] -> [User Aspect] * [USER ASPECT]: User can control the aspect ratio by adjusting width and height of the display. - See section “7.
5. Menu Operations FHD High Bright Field Monitor 18 [4] VIDEO VIDEO이 F-7H SCAN ZERO SCAN ASPECT 16:9 H/V DELAY OFF BLUE ONLY OFF USER ASPECT HOR USER ASPECT VER 3G FORMAT NORMAL H/V FLIP OFF ZOOM OFF ZOOM SPLIT OFF + + 0 0 PAGE (1/2) • H/V FLIP - Allows the displayed image to be flipped horizontally or vertically. - This feature provides flexible mounting options for camera operators.
5. Menu Operations VIDEO이 DSLR DSLR SCALE TIMECODE FOCUS ASSIST FOCUS AS COLOR FOCUS AS LEVEL SCR TALLY SCR OP LEVEL SCR TALLY COL LOW BAT DIS F-7H CANON 7D LIVE VIEW OFF OFF RED + 90 OFF LOW RED OFF PAGE (2/2) • DSLR - Select the DSLR camera to be used with the monitor. Available mode is [CANON 7D]. * DSLR cameras’ screen size and aspect ratio of Live / Record / Playback modes vary depending to their manufacturer. • DSLR SCALE - This is a special function for CANON/NIKON DSLR cameras.
5. Menu Operations [4] VIDEO FHD High Bright Field Monitor 20 VIDEO이 DSLR DSLR SCALE TIMECODE FOCUS ASSIST FOCUS AS COLOR FOCUS AS LEVEL SCR TALLY SCR OP LEVEL SCR TALLY COL LOW BAT DIS F-7H CANON 7D LIVE VIEW OFF OFF RED + 90 OFF LOW RED OFF PAGE (2/2) • SCR TALLY - Used to set Tally operation according to the input level of TALLY IN terminal which is among the terminals of XLR 4P connector in the rear. • SCR TALLY LEVEL - Used to set the input level of Tally operation. (Open&Low : less than 0.
5. Menu Operations [5] WAVEFORM ENABLE TYPE INTENSITY TRANS SIZE LINE WAVEOFORM SEL LINE POS LUMA CHECK LUMA ADJUST RANGE ERROR Y MAX Y MIN C MAX C MIN Y PICTURE BLINK C PICTURE BLINK F-7H OFF OFF + 90 OPAQUE SAMLL OFF + 90 OFF + 90 OFF + + + + 90 90 90 90 OFF OFF • ENABLE - Used to activate/ deactivate the Waveform which is selected in the Waveform/Vector Type menu. • TYPE - This function sets the Waveform and Vectorscope. Available options are different according to the Input signal.
5. Menu Operations [5] WAVEFORM FHD High Bright Field Monitor 22 WAVEFORM ENABLE TYPE INTENSITY TRANS SIZE LINE WAVEOFORM SEL LINE POS LUMA CHECK LUMA ADJUST RANGE ERROR Y MAX Y MIN C MAX C MIN Y PICTURE BLINK C PICTURE BLINK F-7H OFF OFF + 90 OPAQUE SAMLL OFF + 90 OFF + 90 OFF + + + + 90 90 90 90 OFF OFF • LUMA CHECK - Displays the Luma(Y’) level of the input image in colors. - Can select between [Color Pattern] or [Zebra Pattern].
5. Menu Operations [5] WAVEFORM WAVEFORM F-7H OFF OFF + 90 OPAQUE SAMLL OFF - Used to set whether or not to blink pixels with values exceeding Y MAX and Y MIN. • C PICTURE BLINK + 90 OFF - Used to set whether or not to blink pixels with values exceeding C MAX and C MIN. + 90 OFF + + + + 90 90 90 90 OFF OFF • Y MAX - Used to set the maximum Luma(Y’) level from 0 to 255. - Pixels with values exceeding the max Y’ level will blink on the screen, and be displayed in red on the Waveform.
5. Menu Operations FHD High Bright Field Monitor 24 [6] AUDIO AUDIO F-7H VOLUME AUD LEFT AUD RIGHT LEVEL METER LVM DISPLAY LVM REFERENCE LVM SIZE PEAK DECAY TIME + 90 OFF FOF OFF PAIR -18dB SMALL + 90 • VOLUME - Used to control the output volume for the [AUDIO OUT] on the back of the monitor. - Control range is from 0 to 30. • AUD LEFT - Used to set embedded audio channel for left audio out of [AUDIO OUT] terminal on the back of the monitor. - Available values are between CH1~CH16 and Ext..
5. Menu Operations [7] SYSTEM F-7H DEFAULT LUMINANCE INTERNAL PAT SW UPGRADE OFF + 48 VERSION SERIAL NUM SW 00 FPGA 00 BOARD 00 12345678 OFF OFF • DEFAULT - Used to initialize OSD values to factory default. - Available modes are DEFALUT and FACTORY. - In the DEFALUT mode, except for the stored 3D LUT, all values are initialized. - In the FACTORY mode, all values are initialized to factory default. • LUMINANCE - Used to indicate the current Luminance value .
6. Button Functions [1] Input Button FHD High Bright Field Monitor 26 SDI HDMI NO VIDEO • F-7H unit is capable of processing SDI /HDMI Input signal. 1. Press the[MENU
7. Other Functions [1] User Aspect • Used to adjust the Width /Height display ratio. 1. Select [Aspect] mode in the OSD menu by pressing the function button on the right top of the monitor to activate the [USER ASPECT] mode. 2. After the activation, press the Knob to begin controlling. Adjust the ratio using the knob. - Adjust the ratio using the Knob. - Control range for width: 0~1920. - Control range for height : 0~1080. - The size-adjusted picture always stays in the center of the screen.
7. Other Functions [2] Waveform / Vectorscope FHD High Bright Field Monitor 28 • Waveform Y - Displays the Luma(Y’) component of the input signal into waveform. • VectorScope - Displays the color components ‘B-Y’ and ‘R-Y’ of the input signals onto the X-Y axis. - Two different types of Vetorscopes are displayed according to SD or HD input signals. - 100% and 75% scales are indicated on the Vetorscope. • Waveform Cb, Cr - Displays the Cb, Cr components of the input signal into waveform.
7. Other Functions • Used to select specific Vertical Line for WaveForm/VectorScope. [4] Zoom • Used to magnify the input signal from 0% to 90%. - This is available when LINE WaveForm is activated. - Supports Zoom Width Scroll / Zoom Height Scroll function. - To activate this feature, go to [Waveform][Waveform/Vector]-[Line Waveform]- [Select Line Position] and use the Knob to select a vertical line. - Zooms IN/OUT focused on the scrolled area. - Selected line is indicated in White on the screen.
7. Other Functions [5] Luma(Y’) Zone Check FHD High Bright Field Monitor 30 • Color Pattern Type - Displays the Luma(Y’) level of the input image in colors. - Y’ ≥ 100% : Pixels with higher Y’ level than 100 turn to red. - Y’ ≤ 0% : Pixels with lower Y’ level than 0 turn to green. - Pixels with Y’ levels designated by the user are displayed in following colors - yellow, pink, cyan.
7. Other Functions • Focus Assist function assigns a color to the pixels in the shape or the boundary of the image to inform the user to achive the best focus. - With this function, user can easily differenciate the focused area from the outfocused area especially when shooting with a shallow depth of field. - Available types are [Mono] and [Color] types. * [Mono] : Background image is mono type. * [Color] : Background image is original color type.
7. Other Functions [8] DSLR Scale FHD Viewfinder Monitor 32 • This function is designed for some DSLR cameras of Canon(7D) that output different resolution from the operation mode (StandBy, Record, Play Back) • Select the Camera model in the [Display/ Vide]- [DSLR Camera Sel.] menu. • CANON (5D/550D) - In StandBy mode of Canon 5D Mark II, 1080i of HD resolution is indicated.
7. Other Functions • Video source from ‘HDMI input’ terminal can be output through ‘SDI throughout’ terminal. [10] SDI To HDMI Conversion-Out ●● 3G/HD/SD SDI signals from‘SDI input’ terminal can be output through‘HDMI out’terminal. Output Format ※Note: HDSLR camera manufacturers usually specify the resolution and frame rate for the recording. The signal format that is output through HDMI terminal of cameras may differ from makers to makers.
FHD High Bright Field Monitor 34 7. Other Functions [11] Screen Tally/Rear Tally [12] Internal Pattern • Activates with the Rear Tally on the rear of the monitor at the same time. • Displays internally generated test patterns. • Screen TALLY On/Off - Used to set Tally operation according to the input level of TALLY IN terminal which is among the terminals of XLR 4P connector in the rear. • Screen TALLY Operating Level - Used to set the input level of Tally operation. (Open&Low : less than 0.
7. Other Functions [13] Firmware Upgrade 1. Connect the USB to the USB Slot on the front of the monitor. 2. Select what to update among CPU / FPGA / ALL in [S/W UPGRADE]. 3. When the USB connection is completed, the S/W upgrade starts and the progress displays on the bottom left side of the screen. 4. If the USB doesn’t connect properly or there is no fi le in the specifi ed location, the error message will be displayed on the bottom left side of the screen and the upgrade won’t start. 5.
8. Available Signal Formats This unit is applicable to the following signal formats : FHD High Bright Field Monitor 36 Input Signal VIDEO PC 480 / 59.94i (NTSC) 480 / 60p 576 / 50i (PAL) 576 / 50p 720 / 23.98p 720 / 24p 720 / 25p 720 / 30p 720 / 50p 720 / 59.94p 720 / 60p 1080 / 23.98PsF 1080 / 24PsF 1080 / 25PsF 1080 / 23.98p 1080 / 30PsF 1080 / 29.97PsF 1080 / 24p 1080 / 25p 1080 / 29.97p 1080 / 30p 1080 / 50i 1080 / 50p 1080 / 59.94i 1080 / 60i 1080 / 59.
9. Video Support Resolution VIDEO Support Resolution Input Signal Interfaces Input Signal Interfaces 3G-SDI (A/B) single link Input Signal Interfaces HD SDI single link Input Signal Interfaces HD SDI single link 720x487 (59.94i) 720x576 (50i) YCbCr 4:2:2 10bit Signal Format (3G SDI) 1920x1080 (60p/59.94p/50p) YCbCr 4:2:2 10bit 1920x1080 (30/29.97/25/24/23.98/ 30sF/29.97sF/25sF/24sF/23.98sF) RGB 4:4:4 10bit / 12bit YCbCr 4:4:4 10bit / 12bit Signal Format (HD SDI) 1920x1080 (23.98/24/25/29.
10. Product Specifications F-7H FHD High Bright Field Monitor 38 LCD Input Output Input Signal SDI Input Signal Formats Size 7” Resolution 1920×1080 (16:9) Pixel Pitch 0.079(H) X 0.076(W) mm Color Depth 16.7M Luminance of white 3600 cd/ m2 (Max.) Contrast Ratio 1200 : 1 Display Area 151.2(H)x94.5(V) mm 1 X HDMI HDMI Input 1Ch 1 X BNC 3G/HD/SD SDI Input 1Ch 1 X HDMI HDMI Output 1Ch 1 X BNC 3G/HD/SD SDI Output 1Ch 3G-SDI 2.970Gbps HD-SDI 1.
11.
FHD High Bright Field Monitor 40 MEMO
FHD High Bright Field Monitor 41 MEMO
FHD High Bright Field Monitor 42 MEMO
FOR MORE INFORMATION PLEASE VISIT : http://www.tvlogic.tv 부사장 12F, ACE HIGH-END 8, 345-4 Gasan-dong, Geumcheon-gu, Seoul, 18590, KOREA TEL : +82-70-8668-6611, FAX : 82-2-6123-3201, E-mail : sales@ t vlogic.co.kr 153-802 서울특별시 금천구 가산동 345-4 조 성 일 Mobile.
