SC-2K Single Column Platform Storage Lift (Turf & Power Sport) 2,000 lb.
INDEX PREFACE--------------------------------------------------------------------------- PAGE 2 IMPORTANT NOTES------------------------------------------------------------ PAGE 3 DEFINITION------------------------------------------------------------------------ PAGE 3 SITE PREPERATION------------------------------------------------------------ PAGE 3 REQUIRED TOOLS-------------------------------------------------------------- PAGE 4 GENERAL INFORMATION----------------------------------------------------- PA
IMPORTANT NOTES READ THE INSTALLATION AND OPERATION MANUAL IN ITS ENTIRETY BEFORE ATTEMPTING TO INSTALL THE LIFT. • Do not install this lift on any surface other than concrete, conforming to minimum specifications. • Do not install this lift over expansion joints or cracks. Check with building architect. • Do not install this lift on a second floor with a basement beneath without written authorization from building architect.
REQUIRED TOOLS The installation of this lift is relatively simple and can typically be accomplished by 2 men in a few hours. The following tools and equipment are needed or recommended. • • • • • • • • • • • • • Fork Lift and/or Engine Hoist for moving pieces & positioning lift column, is recommended. (You will also need a ten-foot length of 3/8” chain.) Rotary Hammer Drill with 3/4” Masonry Drill Bit.
SC-2K Apr 2018
SPECIFICATIONS Specifications SC-2K Capacity 2,000 lbs. Width Overall 64-5/8” Height Overall 84-1/2” Depth Overall 69-1/2" Lift Rise Height 58" Platform Height 2-3/4" Platform Frame Size 64-1/2”W x 47-3/8”D Platform Aluminum Deck Size 36”W x 48”D Platform Structure Size 64-1/2”W x 52-5/8”D Ship Weight (motor pump included) 605 lbs. Power 115 VAC, 1PH, 20 Amp IMPORTANT! RECEIVING & HANDLING 1.
2-3/4” 58” 84-1/2” DIMENSIONS 47-3/8” 52-5/8” Fig.
INSTALLATION (Ensure to Read the Operating Instructions before Operating Lift) Make sure you have someone to assist with installation as most of the lift components are big, heavy, and cumbersome. The lift column alone weighs about 330 lbs. by itself. The platform frame & aluminum decking weighs around 200 lbs. together.
IMPORTANT! The major piece of the lift is the column assembly. It consists of the carriage, hydraulic cylinder, chain hydraulic hose and safety latch release cable already pre-assembled. The column assembly will have a bracket on the side, which will be used for installing the power unit later. The cylinder in the column may appear to be loose in the column, this is normal. After installation, when the platform is raised under power, the cylinder should stabilize itself in an upright plumb position.
STEP 2 Using two people, carefully stand the column upright and maneuver to the predetermined location (Figs.12 & 13). Fig. 12 Fig. 13 STEP 3 Before proceeding, double check measurements and make certain that the base of the column is properly aligned and in the desired location before anchoring column to floor. a) Using the base plate on the column as a guide, drill each anchor hole into concrete using a rotary hammer drill and 3/4” concrete drill-bit.
STEP 5 a) Attach the power unit to the mount bracket on the side of the Column using the M8 Bolts, Washer and Lock Nuts supplied with Power Unit (Fig.17). b) Remove the red plug from valve body and install the Elbow Fitting (Figs. 18 & 19). Fig. 17 Fig. 18 Fig. 19 c) Connect one end of the Hydraulic Hose to the Elbow Fitting installed on Power Unit (Fig. 20). d) Connect the other end of Hydraulic Hose to the cylinder fitting located on the lower backside of Column (Fig.21).
OPERATING INSTRUCTIONS To Raise, push the power switch button on the power unit and hold while it the electric motor turns on. The motor operates an internal pump that forces hydraulic oil into the lift piston, which extends the piston rod & roller chain to raise the lift (Fig 22). As the lift rises, an internal safety latch will pass over the steel latch stops (rectangular blocks which protrude from the back, inside of the lift column), and you will hear “clanks” as it does so.
RAISING A VEHICLE With Lift in the fully lowered position, carefully drive or push vehicle (Lawnmower or ATV) onto Platform until relatively centered. Then, set parking brake. NOTE: Ensure wheels are positioned on the Platform Frame only. Aluminum Decking is not designed to be load bearing. Depress the “up” button and the vehicle will rise. Raise the vehicle until it is near the ceiling of the garage.
EXPLODED VIEW 14 SC-2K Apr 2018
PARTS LIST ITEM Tux P/N M-Ref P/N DESCRIPTION QTY 1 SC-2K-01 5202-0001 6-000 NUT, M16 3 2 SC-2K-02 5104-16030-000 BOLT, M16 X 30 3 3 SC-2K-03 5206-00020-000 NUT, M20 2 4 SC-2K-04 SJ03-00013-000 KEY RING 1 5 SC-2K-05 TC01-02005-000 LOCK RELEASE CABLE 1 6 SC-2K-06 TC01-02001-000 LOCK RELEASE SPRING 1 7 SC-2K-07 5302-00020-000 FLAT WASHER, # 20 2 8 SC-2K-08 5103-20065-000 BOLT, M20 X 65 2 9 SC-2K-09 TC01-02104-000 SPRING 1 10 SC-2K-10 5106-06040-000 SCREW, M
POWER UNIT PRIMING WARNING!! Failure to properly relieve pressure in the following steps can cause injury to personnel.
LIMITED WARRANTY Structural Warranty: The following parts and structural components carry a five year warranty: Columns Legs Tracks Arms Carriages Cross Rails Uprights Overhead Beam Top Rail Beam Swivel Pins Limited One-Year Warranty: Tuxedo Distributors, LLC offers a limited one-year warranty to the original purchaser of Lifts and Wheel Service equipment in the United States and Canada.
