RJ-45 Rolling Bridge Jack 4,500 lb.
TABLE OF CONTENTS Specifications.......................................................................................................... Description & Features……………………………………………………………......... Installation Instructions........................................................................................... Safety Instructions.................................................................................................. Operating Instructions.............................................................
DESCRIPTION The RJ-45 Rolling Jack is a hand pump operated, scissors style rolling bridge jack, designed to be mounted on four-post or scissor lift’s jack rails, between runways. It is capable of lifting the wheels off runways to provide ‘wheels free’ service for brake, suspension, tire repairs and maintenance. FEATURES A. Lifting capacity of the RJ-45 Rolling Jack is 4,500 lbs. (2000 kg). B. The roller body assembly wheels are adjustable for an inside runway width of 33.9" (861 mm) minimum to a 49.
INSTALLATION INSTRUCTIONS 1. Carefully remove rolling jack from crate package. 2. Pump jack to top by the hand pump. Check that the hydraulic oil quantity is enough and hose is properly connected. 3. Lower the jack completely down by moving the lock release lever to the right, while turning the hydraulic release valve knob counter-clockwise. 4. Slide out the roller body assembly extensions on both sides to match the width between the runways. 5. Place the jack on the rails of the runways (Fig.
OPERATING INSTRUCTIONS WARNING!!! To avoid personal injury and/or property damage, permit only trained personnel to operate jack. After reviewing these instructions, get familiar with jack controls by running the jack through a few cycles before loading vehicle on jack. Observe and avoid any pinch point areas of the linkage mechanism. 1. Before loading a vehicle onto lift, ensure jack(s) are fully lowered. Make sure the adapters are in their most inbound and lowest position.
MAINTENANCE INSTRUCTIONS WARNING! If you are not completely familiar with automotive lift maintenance procedure, please contact your distributor for instructions before any practice. TO AVOID PERSONAL INJURY, permit only qualified personnel to perform maintenance on this equipment. Daily: • Inspect rolling jack adapters for damage or excessive wear. • Inspect hydraulic system for leaks. • Inspect for loose bolts, broken/damaged components. • Inspect linkages for damage, wear and tear.
TROUBLE SHOOTING TROUBLE Rolling Jack will not raise after contacting load Rolling Jack will not raise to full height. Jack drifts down - will not hold. Jack lowers slow or not at all. CAUSE 1. Jack loaded beyond capacity. 2. External fluid leak at pump, hose or cylinder. 3. Internal leakage. REMEDY 1. Use Jack only to rated capacity. 2. Repair leak, refill reservoir.* 2. External leakage. 2. Locate leak and repair. Refill reservoir.* 3. Internal leakage. 3.
EXPLOED VIEW 8 RJ-45 July 2017
PARTS LIST ITEM Tux P/N 1 RJ-45-001 2 RJ-45-002 3 RJ-45-003 4 RJ-45-004 5 RJ-45-005 6 RJ-45-006 7 RJ-45-007 8 RJ-45-008 9 RJ-45-009 10 RJ-45-010 11 RJ-45-011 12 RJ-45-012 13 RJ-45-013 14 RJ-45-014 15 RJ-45-015 16 RJ-45-016 17 RJ-45-017 18 RJ-45-018 19 RJ-45-019 20 RJ-45-020 21 RJ-45-021 22 RJ-45-022 23 RJ-45-023 24 RJ-45-024 25 RJ-45-025 25.1 RJ-45-025.1 26 RJ-45-026 27 RJ-45-027 28 RJ-45-028 29 RJ-45-029 30 RJ-45-030 30.1 RJ-45-030.
33 34 35 36 37 37.1 37.2 37.3 37.4 37.5 37.6 37.7 37.8 37.9 38 39 40 41 42 47 48 49 50 51 52 53 54 55 RJ-45-033 RJ-45-034 RJ-45-035 RJ-45-036 RJ-45-037 RJ-45-037.1 RJ-45-037.2 RJ-45-037.3 RJ-45-037.4 RJ-45-037.5 RJ-45-037.6 RJ-45-037.7 RJ-45-037.8 RJ-45-037.
RJ-45 July 2017
