RAJ-6K Series Rolling Bridge Jacks 6,000 lb. Capacity (High Mount & Low Mount) RAJ-6K-H (High Mount) RAJ-6K-L (Low Mount) ASSEMBLY & OPERATION INSTRUCTION MANUAL Oct.
TABLE OF CONTENTS Specifications........................................................................................................... 2 Description & Features.............................................................................................3 Installation Instructions.............................................................................................3 Safety Instructions....................................................................................................
DESCRIPTION This RAJ-6K-H & RAJ-6K-L Rolling Jacks are pneumatic / hydraulic operated, scissor-style rolling bridge jacks, designed to be mounted on four post or scissor lift’s jack rails, between runways. Both models are capable of lifting the wheels off runways to provide ‘wheels free’ service for brake, suspension, tire repairs and maintenance. The universal adjustable Roller Body design comes in both high & low mount model configurations for low & high jack rail designs.
SAFETY INSTRUCTIONS • Never allow unauthorized or untrained persons to operate the rolling jack. • Thoroughly train all employees in the use and care of rolling jack. • Never overload rolling jack. Capacity of rolling jack is stated on the nameplate. Capacity should not be exceeded. • Observe and avoid any pinch point areas of the linkage mechanism.
Air / Hydraulic Pump Diagram Air Fitting / Inlet Port Fitting / Hydraulic Hose Press to Raise Press to Lower Fig 2. MAINTENANCE INSTRUCTIONS WARNING! If you are not completely familiar with automotive lift maintenance procedure, please contact your distributor for instructions before any practice. TO AVOID PERSONAL INJURY, permit only qualified personnel to perform maintenance on this equipment. Daily: • Inspect rolling jack rubber blocks for damage or excessive wear.
TROUBLE SHOOTING TROUBLE Rolling Jack will not raise after contacting load Rolling Jack will not raise to full height. Jack drifts down - will not hold. Jack lowers slow or not at all. CAUSE 1. Jack loaded beyond capacity. 2. External fluid leak at pump, hose or cylinder. 3. Internal leakage. REMEDY 1. Use Jack only to rated capacity. 2. Repair leak, refill reservoir.* 2. External leakage. 2. Locate leak and repair. Refill reservoir.* 3. Internal leakage. 3.
EXPLOED VIEW RAJ-6K-H (High Mount) Roller Body RAJ-6K-L (Low Mount) Roller Body RAJ-6K-H (High Mount #27) Roller Body Assy. RAJ-6K-L (Low Mount #29) Roller Body Assy. 29 29 7 RAJ-6K-H & RAJ-6K-L Oct.
PARTS LIST ITEM Tux P/N M-Ref P/N DESCRIPTION QTY 1 RAJ6K-001 LJ01-00007-000 Rubber Block 2 2 RAJ6K-002 LJ01-02000-000 Sliding Arm 2 3 RAJ6K-003 LJ01-08000-000 Arm Weldment 1 4 RAJ6K-004 LJ01-00005-000 Side Curtain 2 5 RAJ6K-005 LJ01-00004-000 Screw, M6 x 8mm 16 6 RAJ6K-006 LJ01-00009-000 Shaft #3 1 7 RAJ6K-007 LJ01-00001-000 Slide Block #1 4 8 RAJ6K-008 LJ01-00006-000 Slide Block #2 2 9 RAJ6K-009 LJ01-07000-000 Inner scissor 1 10 RAJ6K-010 LJ01-03000-000
RAJ-6K-H (High Mount) Roller Body Assembly Parts (#27) ITEM Tux P/N M-Ref P/N DESCRIPTION QTY 27-1 RAJ6K-027.1 5206-00006-000 Lock Nut, M6 8 27-2 RAJ6K-027.2 5301-00006-000 Flat Washer, D6 16 27-3 RAJ6K-027.3 LJ04-01001-000 8 27-4 RAJ6K-027.4 LJ04-01003-000 27-5 RAJ6K-027.5 5104-06030-000 Small, Side Bearing (High Mount) RB Support Frame Bolt, M6 x 30mm 4 27-6 RAJ6K-027.6 5105-10030-000 Socket Head Bolt, M10 x 30mm 4 27-7 RAJ6K-027.
RAJ-6K-H & RAJ-6K-L Oct.
