MSC-6KLP ‘Low Profile’ Mobile Single Column Lift 6,000 lb. Capacity (1,500 lbs.
INDEX PREFACE------------------------------------------------------------------------------- PAGE 2 GENERAL INFORMATION--------------------------------------------------------- PAGE 3 INSTALLATION------------------------------------------------------------------------ PAGE 6 OPERATION INSTRUCTIONS---------------------------------------------------- PAGE 11 EXPLODED VIEWS & PARTS LIST---------------------------------------------- PAGE 13 LIMITED WARRANTY-------------------------------------------------------
1. GENERAL INFORMATION The iDEAL MSC-6KLP 6,000 lb. capacity can be used in a typically service bay, outside an existing bay or a home garage with limited space as long as the concrete is flat. With a lifting height of 72” the iDEAL MSC-6KLP’s design allows access to the underside of most vehicles making it ideal for pre-service inspections or maintenance. Around the vehicle access makes wheel service possible on most vehicles.
1.2 DIMENSIONS (mm / inch) Fig.
IMPORTANT! Be sure to read the operating instructions before operating your lift! Make sure you have made all necessary measurements to assure that your lift will fit in your shop / garage and accommodate the car you intend to lift with it. Make sure you have enough clearance at the top, and enough width to allow walking around. Also, be aware that the electrical power supply requirements are 115 volt, 1 Phase, 20 amps.
2. Installation For installation you will need common hand tools that most homeowners have, like screwdrivers and pliers, but in addition, you will need some tools that are not common. Each installation is somewhat different, and depends on how much room you have to work around installing the lift. Below is a chronological sequence of installation steps, with the associated tools. Required Tools 1. Fork Lift to unload lift upon delivery 2.
STEP 1 Carefully remove shipping packaging and brackets. Remove all components & parts. Position the base plate on the ground. (Fig. 3) Fig. 3 Fig. 4 STEP 2 Carefully stand the column upright, align the bolt holes and secure to base plate with bolts. (Fig.4) STEP 3 Position the lifting frame to the front of the base plate. Then connect the lifting frame to carriage with bolts. (Fig. 5) Fig. 5 Fig. 6 STEP 4 Mount the hydraulic motor pump on the column with bolts and nuts. (Fig.
STEP 5 Remove the lock pin on the pallet jack (Fig. 10). Place steel ball on the top of the jack ram (Fig.11) Fig. 10 Fig. 11 Insert the ram into the hole of the base plate (Fig. 12). Lock the ram by threaded pin (Fig.13). the length of the ram. (Fig. 14 & 15) Fig. 12 Fig. 13 Fig.14 Put the slot of the bearing into the bracket (Fig. 16) then lock it by bolt (Fig. 17 & 18). Fig. 15 Fig. 16 Fig. 17 The base plate with pallet jack assembly is now complete. 8 MSC-6KLP Aug 2017 Fig.
STEP 6 Locate the offside (opposite column side) arm restraint components (Fig. 19). restraints inside the lifting frame’s end. (Figs. 20 - 23) Fig. 19 Fig. 21 Assemble offside arm Fig. 20 Fig. 22 STEP 7 Assemble the off side arms & handles to the end of lifting frame. (Figs. 24 & 25) Fig. 24 Fig. 25 9 MSC-6KLP Aug 2017 Fig.
STEP 8 Assemble the main side arm restraints for column side & swing arms to lifting frame. (Figs 26 & 27) Fig. 26 Fig. 27 STEP 9 Attach latch release cable bracket to carriage (Fig. 28). Ensure latch release cable is routed thru hole in bracket. Fig. 28 STEP 10 Remove the plastic fill cap from the topside of the reservoir and fill the reservoir with approx. 12 quarts of Non-Detergent / Non-Foaming Hydraulic Oil - SAE-10, AW 32 or equivalent.
3. OPERATION INSTRUCTIONS To Raise, push the power switch button on the power unit and hold while it the electric motor turns on. The motor operates an internal pump that forces hydraulic oil into the lift piston, which extends the piston rod & roller chain to raise the lift. (Fig 29.) As the lift rises, an internal safety latch will pass over the steel latch stops (rectangular blocks which protrude from the back, inside of the lift column), and you will hear “clanks” as it does so.
RAISING A VEHICLE The MSC-6KLP can conveniently be positioned to raise a vehicle using two different methods: 1. Driving the vehicle over the MSC-6KLP base utilizing the ramps feature: • Ensure Swing Arms are positioned to the outer positions and the Lift is positioned on a flat level surface, able to properly support the load. Carefully drive vehicle over the ramps until it’s close to being centered. Set the parking brake. Position arms under the vehicle to lift at the vehicle’s proper pick-up points.
4. EXPLODED VIEWS & PARTS LIST Exploded View A.
Exploded View B.
PARTS LIST ITEM Tux P/N M-Ref P/N DESCRIPTION QTY 1 MSC-6KLP-001 DJ01-01000-M00 Base 1 2 MSC-6KLP-002 5304-00025-000 Circlip, D25 4 3 MSC-6KLP-003 DJ01-00010-M00 Roller 2 4 MSC-6KLP-004 5602-52025-000 Bearing, D52xD25x15 4 5 MSC-6KLP-005 DJ01-00011-M00 Roller Pin 2 6 MSC-6KLP-006 DJ01-00012-M00 Roller Bushing 4 7 MSC-6KLP-007 DJ01-00020-M00 Hook 4 8 MSC-6KLP-008 5301-00006-000 Flat Washer, D6 8 9 MSC-6KLP-009 5303-00006-000 Spring Washer, D6 8 10 MSC-6KLP-0
46 MSC-6KLP-046 5309-00010-000 Circlip, D10 1 47 MSC-6KLP-047 5603-00016-000 Seal Ring, D16 1 48 MSC-6KLP-048 DJ02-00027-000 Cylinder Key Tab 1 49 MSC-6KLP-049 5206-00020-000 Lock Nut, M20 1 50 MSC-6KLP-050 5201-00020-000 Nut, M20 1 51 MSC-6KLP-051 5101-08030-000 Bolt, M8x30 1 52 MSC-6KLP-052 DJ01-00004-M00 Chain Pin 2 53 MSC-6KLP-053 5404-03020-000 Split Pin, D3x20 4 54 MSC-6KLP-054 DJ01-00003-M00 Upper Chain Block 1 55 MSC-6KLP-055 DJ01-12000-M00 Carriage 1
93 MSC-6KLP-093 DJ01-03000-M00 Lifting Frame 1 94 MSC-6KLP-094 5105-16025-000 Bolt, M16x25 1 95 MSC-6KLP-095 5105-16040-000 Bolt, M16x40 8 96 MSC-6KLP-096 5301-00010-000 Flat Washer, D10 4 97 MSC-6KLP-097 5101-10035-000 Bolt, M10x35 4 98 MSC-6KLP-098 DJ01-05000-M00 RH, Mainside Arm 1 99 MSC-6KLP-099 DJ01-07000-M00 RH, MS Arm Extension 1 100 MSC-6KLP-100 DJ01-11000-M00 RH, OS Arm Extension 1 101 MSC-6KLP-101 DJ01-09000-M00 RH, Offside Arm 1 102 MSC-6KLP-102 DJ01
LIMITED WARRANTY Structural Warranty: The following parts and structural components carry a five year warranty: Columns Legs Tracks Arms Carriages Cross Rails Uprights Overhead Beam Top Rail Beam Swivel Pins Limited One-Year Warranty: Tuxedo Distributors, LLC (iDEAL) offers a limited one-year warranty to the original purchaser of Lifts and Wheel Service equipment in the United States and Canada.