Installation Instructions
— —
5
— —
4
Under-mount Sinks Installation
Step 3
Locate and drill the mounting holes (following
the countertop manufacturer’s instructions) as
shown below. Holes should allow even spacing
of mounting brackets around the sink. Please use
the fasteners recommended by the counter top supplier.
Step 4 (Install the Sink)
Clean the bottom of the counter top and the top
flange. Then apply a bead of silicone adhesive
sealant to the top edge of the bowl flange and
position the bowl in the counter top. The easiest
way to handle the sink is via the drain hole or
holes, especially if it's a double bowl model.
Step 4
Undermount sinks can be installed with two different reveals - Reveal, Flush Deciding
on your preferred Look must be done prior to installation.(See diagram)
Reveal - The counter top edge sits approximately 1/4" back
from the edge of the sink, exposing the sink rim.
Flush - The counter top meets the edge of the sink, fitting
flush with the sink bowls.
Step 5
Position and align the sink under the counter top opening.
Press silicone onto counter top.
Step 6
Tighten fasteners until the mounting brackets are snug
against the sink.
NOTE :
Do not fully tighten one clip at a time. Par tially tighten
a clip, then par tially tighten the clip across from it.
After each clip is partially tightened, repeat the
process, fully tightening each clip. This ensures a
secure installation and avoids damage to the sink.
Counter top
Sink
Screws
Fasteners
Step 6
Step 7
Check the alignment of the sink to countertop opening.
Step 8
Tighten down the fasteners evenly. Be careful not to
overtighten. Remove excess silicone.
Step 2 (Out With The Old)
Here's how to remove the old sink:
A. Shut off the water supply valves.
B. Disconnect the water supply fittings.
C. Disconnect the drain fittings.
D. From the underside of the sink, with your
flashlight and long screwdriver, loosen and
remove the frame clamps or rim fasteners.
E. Lift the entire sink out of the counter top.
If this is a new counter top installation, please refer to the countertop
manufacturer’s instructions.
If this is a replacement sink, see Step 2.
Reveal
Flush
Step 8
View from under counter.
Step 2
NOTE : Skip step 2 if this is a new installation.
Step 1
THIS STEP IS ONLY FOR NEW COUNTERTOP
INSTALLATIONS.
Position template on countertop. Locate the
template front to rear, so that sink will not
interfere with the cabinet.
NOTE :
Metal surfaces can be sharp and can cause severe cuts.
Please use gloves and handle the sink with care.
— —
6
Stainless Steel Sink Care:
After Each Use:
● Remove all objects, pads, grids, cloths, etc., from sink.
● Clean with light soap solution, rinse, drain all water and towel dry.
Regular Maintenance:
Side Walls and Bottom of Sink: Remove stains using a cleaning product that contains mild abrasives; always wipe
in grain direction; rinse well and towel dry. For stubborn stains or scratches use a fine grit scrubbing pad following
direction of sink grain finish. Pay careful attention to the directional change.
Mineral Deposits: Use a cleaning product that contains mild abrasives or a light solution of vinegar and water
(1:20 ratio); rinse well and towel dry.
CAUTION: Stainless steel requires exposure to air; DO NOT leave items, objects, cloths, mats, water, pots and
pans, cast iron, knifes, etc., in sink when not washing. Some items void stainless steel from oxygen and can cause
pitting or rusting.
DO NOT :
● Use steel wool or other metal or coarse scouring pads.
● Stand on or in sink when cleaning windows, reaching for top shelf, painting, etc.
● Drop heavy objects in sink as this will cause denting.
● Leave water, bleach, other cleaners, or chemicals of any type in sink; always rinse sink after any use and dry
with towel.
● Use concentrated bleach; always dilute with water and rinse thoroughly after use.
● Use any acids, drain cleaners, harsh chemicals, paint removers, metal cleaners, etc., in sink.
● Drop sharp objects in sink or use as a cutting surface.
The manufacturer warrants that the par ts and assemblies of this product will be free
from defects in material and workmanship under normal household use for as long as
it is owned by the original consumer purchaser.
This warranty covers the original consumer purchaser only and does not include
business, commercial or industrial use of this product. This warranty shall not apply
to goods which have been subject to accidents, negligence or improper installation.
Our responsibility under this warranty is limited only to the replacement of par ts and no
other costs. Should a malfunction occur within the time covered by this warranty,
replacement par ts may by obtained from the Customer Ser vice Depar tment 1-800-626-3525,
The manufacturer will, at its discretion, provide replacement par ts for installation by the
consumer for any par ts that prove defective under normal usage and service with new and
like or equivalent par ts.
Revised on 12/18/2017
Countertop
Cut On Inside
Countertop
B
Step 1
A
Trace Completely Around
Edge Of Cut-out Template