Installation Instructions
Table Of Contents
- 页 1
- 书签F9A98B08 ESA
- 书签B3636BF6 One Handle Lavatory Faucet
- 书签92691F39 TUSCANY
- 书签D012FED3 Your new faucet is designed for years of trouble-free performance. Keep it looking new by cleaning it periodically with a soft damp cloth. Avoid abrasive cleaners, steel wool, and harsh cleaners at these will dull the finish and void the warranty. Vinegar is suggested as an alternative cleaner and is safe for all finishes.
- 书签E44ACCAC If soldering during the installation of this faucet, remove the seats, cartridges, and washers before adding any heat. The warranty will be voided on these parts if not removed before soldering.
- 书签53E64FC0 Safety glasses should always be worn when cutting or soldering.
- 书签794033FE Always cover your drain before installation to prevent losing parts.
- 书签3F66EF02 For Models : 673-7066
- 书签E424F1D0 Before installation turn off the cold and hot water shut offs. Turn the faucet handle\(s\) on to release the pressure in the system. Before installing the water supply lines to the new faucet, turn on both water supply valves and bleed the water supply lines into a bucket for one minute to remove any debris that could clog the faucet. Wrap ALL threaded connections with Teflon tape in a clockwise direction. When installing the new faucet, turn the connectors finger tight, then use an adjustable wrench to tighten the connectors. Connections that are too tight will reduce the integrity of your system.
- 书签0E01F331 Flashlight
- 书签6F3E5DEE Safety Glasses
- 页 2
- 书签4ECB3360 Socket Wrench
- 书签E090AA18 Metal Washer
- 书签EEDC09E3 22
- 书签72DB0EA6 23
- 书签D484F0EB 24
- 书签CEA8DA79 25
- 书签A66320EF 26
- 书签048791D1 27
- 书签3DBB595E 28
- 书签1001E55A Cover
- 书签0E51D231 Washer
- 书签D4CA55A7 Stopper Core
- 书签29D2CD68 Stopper Housing
- 书签CF7E13C8 Small Washer
- 书签FE10DA59 Large Washer
- 书签CB8478EF Lock Nut
- 书签088D1497 30
- 书签DAE30A25 31
- 书签A887DA13 32
- 书签518783F9 29
- 书签7BB75455 33
- 书签1E97A9D7 Gasket
- 书签B629D9AA Lock Nut
- 书签9869C514 Allen Wrench
- 书签64353D84 Seal
- 书签A040B379 34
- 书签7DA15835 34
- 书签2621D094 O-ring
- 书签6AA6D4A0 O-rings
- 书签2F9BF38D Mounting Bolt
- 书签84398F4C Tube \(Cold\)
- 书签DCEEF445 Tube \(Hot\)
- 页 3
- 书签76E543EA 1. Turn off the water shut offs before installation. Remove the current faucet. Clean and dry the surface the new faucet will be installed on. Note: This faucet fits 3 cm/1-3/16" countertops.
- 书签9FD2D947 2. Deck Plate \(3 Hole\) Installation: Verify the O-ring \(#12\) is in place. Attach the gasket \(#20\) and seal \(#21\) to the deck plate \(#19\), ensuring the notches on the deck plate \(#19\) line up for proper installation. Apply silicone sealant beneath the gasket \(#20\). Install the faucet through the second hole from the left. Note: Do not remove the customer service tag with the model number and phone number. This information will be needed when calling the customer service department.
- 书签7DDB7034 12
- 书签147AD173 20
- 书签5EC7B160 21
- 书签5DCF0FE9 19
- 书签D498BDF6 7
- 书签D043F114 3. Single Hole Installation: Verify the O-ring \(#12\) is in place. Apply silicone sealant beneath the base \(#11\). Install the faucet through the single faucet hole. Note: Do not remove the customer service tag with the model number and phone number. This information will be needed when calling the customer service department.
- 书签70C71ADF 11
- 书签A9962EC3 12
- 书签877E891B 4. From underneath the sink, slide the metal washer \(#30\) onto the mounting bolt \(#16\). Screw on the lock nut \(#31\), then tighten using the socket wrench \(#29\). Hint: Have someone hold the body \(#7\) in place while tightening.
- 书签476D2FE9 Step 1-4
- 书签BD9798C5 30
- 书签253DB33F 31
- 书签3C3BBA2E 29
- 书签41371837 16
- 书签60126E25 7
- 页 4
- 书签55538691 Installation Instructions
- 书签55795A19 25
- 书签779FEE41 26
- 书签F90BFCE1 5. Apply Teflon tape onto the threads of the faucet water supplies in a clockwise direction. Tighten the water supply tubes/lines onto the water supplies. Be sure to connect the cold water supply tube/line to the cold water supply valve \(typically on the right\) and the hot water supply tube/line to the hot water supply valve \(typically on the left\). Use a wrench \(as shown\) to tighten the nut. Hold the tubes/lines into a bucket and turn the water supply valves on for one minute. Turn off the water supply valves.
- 书签CE4D3C1A 6. Apply Teflon tape to the threads of the tubes \(#17 and #18\) in a clockwise direction. Slip 1/2" coupling nuts onto water supply tubes or use flexible stainless steel supply lines \(recommended\) - both are sold separately. Use two wrenches \(as shown\) to keep from twisting the tube \(#17 and #18\) off of the faucet when tightening the nut.
- 书签39866D47 25
- 书签C43F54B0 8. Remove the old drain assembly. Clean the surface to remove the old adhesive and dirt before installing the new drain. Dry the area thoroughly.
- 书签8AE0A5BB 22
- 书签8245F03C 26
- 书签B7FAACD6 27
- 书签CE4422F7 28
- 书签3341A404 7. Remove the lock nut \(#28\), large washer \(#27\), and small washer \(#26\) from the stopper housing \(#25\). Note: Before installation, verify there is no damage to the drain. If there is damage, call customer service for a replacement. Do NOT install damaged parts.
- 书签441B8CC9 9. Place a ring of silicone sealant around the small washer \(#26\) on the stopper housing \(#25\) or the drain opening of the sink. Insert the stopper housing \(#25\) into the drain hole from the top.
- 书签1A7D7182 Step 5-9
- 页 5
- 书签4D0102EC Installation Instructions
- 书签77062354 25
- 书签39A15E76 27
- 书签E26286FC 28
- 书签B8D7EF42 11. Remove the aerator assembly \(#33\). Open the hot and cold shut offs and check for leaks. If a leak occurs, refer to step 6 or 7. Note: Remove by hand. Do NOT use pliers to remove the aerator assembly \(#33\) as this may cause damage.
- 书签CD16C248 10. From underneath the sink, slide the large washer \(#27\) onto the stopper housing \(#25\), then screw on the lock nut \(#28\) hand tight. Do not over tighten. See the diagram for a visual.
- 书签26AB364C 13. Turn on both the hot and cold water and let it run for one minute. This will help clear any debris that may have come loose during installation and prevent the system from becoming clogged. Turn off the water and reinstall the aerator assembly \(#33\).
- 书签79F76E45 12. Close the drain and fill the sink with water. Check for leaks. If water is leaking from the drain, refer to step 10 or 11.
- 书签65923673 8
- 书签0872C4F4 Step 10-13
- 书签F5D50B17 9
- 书签B56E7895 10
- 书签442AD179 33
- 书签1FC9ECE9 8
- 书签43C6DE62 9
- 书签4BAAD6D7 10
- 书签451145DC 33
- 页 6
- 书签C7B861A0 Revised on 11/18/2020
- 书签4BEE6E76 Release the pressure in the faucet system. Remove the handle button \(#3\), set screw \(#2\), handle \(#1\), and trim cap \(#4\). If the lock nut \(#5\) is loose tighten it. If the lock nut \(#5\) is tight, remove the lock nut \(#5\) and cartridge \(#6\). Verify the O-ring is clean and in proper alignment on the cartridge \(#6\). If the O-ring is dirty rinse in warm water. Reinstall the O-ring onto the cartridge \(#6\). Reinstall the cartridge \(#6\), lock nut \(#5\), trim cap \(#4\), handle \(#1\), set screw \(#2\) and handle button \(#3\). Turn the water supply supplies on.
- 书签EF8DAAE3 The lock nut \(#5\) has come loose or the O-ring on the cartridge \(#6\) is dirty or misaligned.
- 书签DD937465 Dirty or damaged cartridge \(#6\).
- 书签11638F4A Release the pressure in the faucet system. Remove the handle button \(#3\), set screw \(#2\), handle \(#1\), trim cap \(#4\), lock nut \(#5\), and cartridge \(#6\). Check the ceramic disk for dirt and damage. Replace the cartridge \(#6\) if damaged. If the cartridge \(#6\) is dirty, soak it in warm white vinegar for 4 hours. Every 30 minutes, while the cartridge \(#6\) is completely submerged, turn the stem on and off 10 times. Reinstall the cartridge \(#6\), lock nut \(#5\), trim cap \(#4\), handle \(#1\), set screw \(#2\), and handle button \(#3\). Turn the water supplies back on.
- 书签E1FD5E3D Troubleshooting
- 书签FB88AB8E Leaks underneath the handle \(#1\).
- 书签D23CF9FA The water will not shut off completely.
- 书签0097E015 The aerator assembly \(#33\) is dirty or misaligned.
- 书签6746CACE The aerator assembly \(#33\) leaks or has an inconsistent water flow pattern.
- 书签004CAD9D Remove the aerator assembly \(#33\), by hand and check the washer \(#8\). If the washer \(#8\) is misaligned, realign the washer \(#8\) and reinstall. If the aerator assembly \(#33\) is dirty, soak it in warm white vinegar for 30 minutes. Reinstall or replace the aerator assembly \(#33\).
- 书签B31EF689 The manufacturer warrants that the parts and assemblies of this product will be free from defects in material and workmanship under normal household use for as long as it is owned by the original consumer purchaser. This warranty covers the original purchaser with original receipt only and does not include business, commercial or industrial use of this product. This warranty shall not apply to goods which have been subject to accidents, negligence or improper installation. Our responsibility under this warranty is limited only to the replacement of parts and no other costs. Should a malfunction occur within the time covered by this warranty, replacement parts may be obtained from Customer Service Department 1-800-626-3525 or email warranty@cmiproduct.com. The manufacturer will, at its discretion, provide replacement parts for installation by consumer for any parts that prove defective under normal usage and care with new or equivalent parts.
- 书签7D1DA5C7 If the installation instructions have been followed carefully and the faucet still does not work properly, take these corrective steps. CAUTION: Faucets are under pressure. For safety, before preforming maintenance on the faucet always turn off the water at the water supply valve and turn on the handle\(s\) to release the pressure.
