Installation Instructions
Table Of Contents
- 页 1
- 书签AD7E0274 Nicole Vessel
- 书签A62D2008 Single Handle Vessel Lavatory Faucet
- 书签C7E3C5B3 TUSCANY
- 书签5BC7E1DA Your new faucet is designed for years of trouble-free performance. Keep it looking new by cleaning it periodically with a soft damp cloth. Avoid abrasive cleaners, steel wool, and harsh cleaners at these will dull the finish and void the warranty. Vinegar is suggested as an alternative cleaner and is safe for all finishes.
- 书签630D05E8 If soldering during the installation of this faucet, remove the seats, cartridges, and washers before adding any heat. The warranty will be voided on these parts if not removed before soldering.
- 书签2C9A6C28 Safety glasses should always be worn when cutting or soldering.
- 书签62AFD6D1 Always cover your drain before installation to prevent losing parts.
- 书签7565CDCA Flashlight
- 书签7A403ECF For Models : 673-6139, 673-6140 673-6141
- 书签E672E234 Before installation turn off the cold and hot water shut offs. Turn the faucet handle\(s\) on to release the pressure in the system. Before installing the water supply lines to the new faucet, turn on both water supply valves and bleed the water supply lines into a bucket for one minute to remove any debris that could clog the faucet. Wrap ALL threaded connections with Teflon tape in a clockwise direction. When installing the new faucet, turn the connectors finger tight, then use an adjustable wrench to tighten the connectors. Connections that are too tight will reduce the integrity of your system.
- 页 2
- 页 3
- 书签FA53A6BE 1. Shut off the water supplies before installation. Remove the current faucet. Clean and dry the surface the new faucet will be installed on. Note: This faucet fits 3 cm/1-3/16" countertops.
- 书签9CD91607 3. Apply Teflon tape to the threads of the copper tube \(hot\) \(#15\) and copper tube \(cold\) \(#16\) in a clockwise direction.
- 书签E0E55CC0 15
- 书签512DE80E 4. Verify the O-ring \(#14\) is in place. Apply silicone sealant beneath the body \(#13\). Install the faucet through the single faucet hole. From underneath, reassemble the gasket assembly \(#18\) and the lock nut \(#19\). Hand tighten the lock nut \(#19\) lining up one of the screws \(#20\) with the groove in the gasket assembly \(#18\). Do not over tighten. Use a Phillips screwdriver to tighten the screws \(#20\) on the lock nut \(#19\). Note: Assemble in the order listed with the rubber washer \(#33\) first. See the diagram for a visual. Hint: Have someone hold the body \(#13\) in place while tightening.
- 书签E4D67B1C 14
- 书签25A96550 13
- 书签B4515A02 2. Remove the lock nut \(#19\) and gasket assembly \(#18\). Note: Do not remove the customer service tag with the model number and phone number. This information will be needed when calling the customer service department.
- 书签9CE86D49 16
- 书签19F39F92 18
- 书签7A2B5D82 19
- 书签36AD361B 20
- 书签31630438 33
- 书签98065454 34
- 页 4
- 书签39E6F023 Installation Instructions
- 书签4DF0BB50 Steps 5-9
- 书签971B5B3F 9. Overflow Hole Instructions: Note: Skip this step if installing the drain into a sink without an overflow hole. Unscrew the cover \(#21\) counterclockwise by hand. Unscrew the stopper core \(#22\) counterclockwise using a pair of pliers if needed. Screw the stopper core \(#22\) into the stopper housing \(with overflow hole\) \(#24\). Screw the cover \(#21\) onto the stopper core \(#22\).
- 书签3D10F462 7. Remove the nut \(#31\), outlet pipe \(#30\), O-ring \(#29\), lock nut \(#28\), wearing ring \(#27\), and washer \(#26\) from the drain assembly. Note: Before installation, verify there is no damage to the push up pop-up drain. If there is damage, please call customer service for a replacement. Do NOT install damaged parts.
- 书签BC13AE29 8. Remove the old drain assembly. Clean the surface to remove the old adhesive and dirt before installing the new drain. Dry the area thoroughly.
- 书签798F3809 4
- 书签1ABA2B69 Teflon
- 页 5
- 书签8889EDB6 32
- 书签5336B824 Installation Instructions
- 书签F2F983D4 13. Remove the aerator assembly \(#32\). Open the hot and cold shut offs and check for leaks If a leak occurs, refer to step 5 or 6. Note: Remove by hand. Do NOT use pliers to remove the aerator assembly \(#32\) as this may cause damage.
- 书签8A68F7A0 14. Close the drain and fill the sink with water. Check for leaks. If water is leaking from the drain, refer to step 10 or 11 to tighten the areas leaking.
- 书签18D1CB57 11. From underneath the sink, slide the washer \(#26\) and wearing ring \(#27\) onto the stopper housing \(#23 or #24\), then screw on the lock nut \(#28\) hand tight. Do not over tighten. See the diagram for a visual.
- 书签2E1B260E 12. Slide the nut \(#31\) over the outlet pipe \(#30\) and insert the O-ring \(#29\) onto the outlet pipe \(#30\). Screw the nut \(#34\) onto the stopper housing \(#23 or #24\) hand tight. Do not over tighten. Note: The outlet pipe \(#30\) connects to the p-trap drain. Refer to the installation instructions for the p-trap for more information on how to connect the outlet pipe \(#30\) to the p-trap drain.
- 书签9261288A 23 or 24
- 书签C3F0D900 25
- 书签CF1EEF59 10. Place a ring of silicone sealant around the washer \(#25\) on the stopper housing \(#23 or #24\) or the drain opening of the sink. Insert the stopper housing \(#23 or #24\) into the drain hole from the top.
- 书签8763E051 Steps 10-15
- 书签B6789EA6 23 or 24
- 书签A483687B 23 or 24
- 书签81197B9E 15. Turn on both the hot and cold water and let it run for one minute. This will help clear any debris that may have come loose during installation and prevent the system from becoming clogged. Turn off the water and reinstall the aerator assembly \(#32\).
- 页 6
- 书签84B8EA60 Installation Instructions
- 书签5242D49C Steps 5-9
- 书签C7B1219C 9. Overflow Hole Instructions: Note: Skip this step if installing the drain into a sink without an overflow hole. Unscrew the cover \(#21\) counterclockwise by hand. Unscrew the stopper core \(#22\) counterclockwise using a pair of pliers if needed. Screw the stopper core \(#22\) into the stopper housing \(with overflow hole\) \(#24\). Screw the cover \(#21\) onto the stopper core \(#22\).
- 书签30569C83 7. Remove the nut \(#31\), outlet pipe \(#30\), O-ring \(#29\), lock nut \(#28\), wearing ring \(#27\), and washer \(#26\) from the drain assembly. Note: Before installation, verify there is no damage to the push up pop-up drain. If there is damage, please call customer service for a replacement. Do NOT install damaged parts.
- 书签D180856F 8. Remove the old drain assembly. Clean the surface to remove the old adhesive and dirt before installing the new drain. Dry the area thoroughly.
- 书签14E61F96 4
- 书签2BC443E9 Teflon
- 书签A833B96F 32
- 书签ECEE700A Installation Instructions
- 书签AAB8FF6B 13. Remove the aerator assembly \(#32\). Open the hot and cold shut offs and check for leaks If a leak occurs, refer to step 5 or 6. Note: Remove by hand. Do NOT use pliers to remove the aerator assembly \(#32\) as this may cause damage.
- 书签63CC8D39 14. Close the drain and fill the sink with water. Check for leaks. If water is leaking from the drain, refer to step 10 or 11 to tighten the areas leaking.
- 书签19EAAFD7 11. From underneath the sink, slide the washer \(#26\) and wearing ring \(#27\) onto the stopper housing \(#23 or #24\), then screw on the lock nut \(#28\) hand tight. Do not over tighten. See the diagram for a visual.
- 书签513EA1D7 12. Slide the nut \(#31\) over the outlet pipe \(#30\) and insert the O-ring \(#29\) onto the outlet pipe \(#30\). Screw the nut \(#34\) onto the stopper housing \(#23 or #24\) hand tight. Do not over tighten. Note: The outlet pipe \(#30\) connects to the p-trap drain. Refer to the installation instructions for the p-trap for more information on how to connect the outlet pipe \(#30\) to the p-trap drain.
- 书签09A5462D 23 or 24
- 书签D50546A7 25
- 书签6A414C93 10. Place a ring of silicone sealant around the washer \(#25\) on the stopper housing \(#23 or #24\) or the drain opening of the sink. Insert the stopper housing \(#23 or #24\) into the drain hole from the top.
- 书签B8CFB2CC Steps 10-15
- 书签D6450441 23 or 24
- 书签D0B267D2 23 or 24
- 书签E2395C05 15. Turn on both the hot and cold water and let it run for one minute. This will help clear any debris that may have come loose during installation and prevent the system from becoming clogged. Turn off the water and reinstall the aerator assembly \(#32\).
- 书签26ABA60B Troubleshooting
- 书签92424A3E If the installation instructions have been followed carefully and the faucet still does not work properly, take these corrective steps. CAUTION: Faucets are under pressure. For safety, before preforming maintenance on the faucet always turn off the water at the water supply valve and turn on the handle\(s\) to release the pressure.
- 书签35C12632 Revised on 11/12/2020
- 书签CED1529A Release the pressure in the faucet system. Remove the handle \(#3\) and trim cap \(#4\). If the lock nut \(#5\) is loose tighten it. If the lock nut \(#5\) is tight, remove the lock nut \(#5\) and cartridge \(#6\). Verify the O-ring is clean and in proper alignment on the cartridge \(#6\). If the O-ring is dirty rinse with warm water. Reinstall the O-ring onto the cartridge \(#6\). Reinstall the cartridge \(#6\), lock nut \(#5\), trim cap \(#4\), handle \(#3\), set screw \(#2\), and handle button \(#1\). Turn the water supplies on.
- 书签4F530DD9 The lock nut \(#5\) has come loose or the O-ring on the cartridge \(#6\) is dirty or misaligned.
- 书签106F0F83 Dirty or damaged cartridge \(#6\).
- 书签11F2649D Release the pressure in the faucet system. Remove the handle button \(#1\), set screw \(#2\), handle \(#3\), trim cap \(#4\), lock nut \(#5\), and cartridge \(#6\). Check the ceramic disk for dirt and damage. Replace the cartridge \(#6\) if damaged. If the cartridge \(#6\) is dirty, soak it in warm white vinegar for 4 hours. Every 30 minutes, while the cartridge \(#6\) is completely submerged, turn the stem on and off 10 times. Reinstall the cartridge \(#6\), lock nut \(#5\), trim cap \(#4\), handle \(#3\), set screw \(#2\), and handle button \(#1\). Turn the water supplies back on.
- 书签1419498A Leaks under the handle \(#3\).
- 书签772297CA The water will not shut off completely.
- 书签990FF65B The manufacturer warrants that the parts and assemblies of this product will be free from defects in material and workmanship under normal household use for as long as it is owned by the original consumer purchaser. This warranty covers the original purchaser with original receipt only and does not include business, commercial or industrial use of this product. This warranty shall not apply to goods which have been subject to accidents, negligence or improper installation. Our responsibility under this warranty is limited only to the replacement of parts and no other costs. Should a malfunction occur within the time covered by this warranty, replacement parts may be obtained from Customer Service Department 1-800-626-3525 or email warranty@cmiproduct.com. The manufacturer will, at its discretion, provide replacement parts for installation by consumer for any parts that prove defective under normal usage and care with new or equivalent parts.
- 书签9A6E8F30 Aerator assembly \(#32\) is dirty or misaligned.
- 书签95E06740 Remove the aerator assembly \(#32\) and check the washer \(#10\). If the washer \(#10\) is misaligned, realign the washer \(#10\) and reinstall. If the aerator \(#11\) is dirty, rinse in warm water. Reinstall or replace the aerator assembly \(#32\).
- 书签56D13FF2 The aerator assembly \(#32\) leaks or has an inconsistent water flow pattern.
