User Manual

2. Specification

2.1 Electrical Specification

2.1.1 Input

DC 7V ~ 30V (36Vpeak), 2A max.

2.1.2 Output (2* USB-A connector)

DC 5.15V ±0.1V, 2A max. (at Vin ≥ DC 6.5V)

2.1.3 Efficiency

The DC-DC converter efficiency is 82% typically at maximum output load and

rated input Voltage range.

2.1.4 Output Ripple & Noise

The output ripple & noise is less than 150mVp-p.

Measurement shall be made with an oscilloscope with 20MHz bandwidth.

Outputs should be bypassed at the connector with a 0.1uF Ceramic disk capacitor

and 47uF electrolytic capacitor.

2.1.5 Reverse input voltage protection

The DC-DC converter is applied to the reverse voltage will not be damaged

even.

2.1.6 UVLO (Under voltage lock out)

The input voltage is less than 8.6V DC-DC converter operates at a 2Cell mode,

8.6V or greater to 3Cell mode works. The setting of Mode is done automatically.

DC-DC converter input voltage is below the UVLO off voltage when the output

is off, the input voltage is above UVLO on voltage, the output is turned on.

2.1.7 LED indicator

The DC-DC converter with LED indicator displays the status of the operation,

and during normal operation LED indicator turns on.

2.2 Environmental Specification

2.2.1 Temperature

i) Operating ambient temperature range : 0℃ ~ 40℃

ii) Storage ambient temperature range : -30℃ ~ 85℃

Mode

UVLO off voltage

UVLO on voltage

2 Cell

6.35V ~ 6.45V

6.45V ~ 6.55V

3 Cell

9.70V ~ 9.80V

9.90V ~ 10.00V

PAGE 1
2. Specification 2.1 Electrical Specification 2.1.1 Input DC 7V ~ 30V (36Vpeak), 2A max. 2.1.2 Output (2* USB-A connector) DC 5.15V ±0.1V, 2A max. (at Vin ≥ DC 6.5V) 2.1.3 Efficiency The DC-DC converter efficiency is 82% typically at maximum output load and rated input Voltage range. 2.1.4 Output Ripple & Noise The output ripple & noise is less than 150mVp-p. Measurement shall be made with an oscilloscope with 20MHz bandwidth. Outputs should be bypassed at the connector with a 0.
PAGE 2
.2.2 Humidity i) Operating ambient humidity range : ≤85% ii) Storage ambient humidity range : ≤95% 2.
PAGE 3
. Test data 3.1 Output voltage, Ripple & noise, Efficiency Test result Test condition Input voltage 8V 12V 24V 30V #1 Output current Vo [V] Iin [A] 0A 1A 2A 0A 1A 2A 0A 1A 2A 0A 1A 2A 5.183 5.178 5.173 5.182 5.178 5.175 5.181 5.181 5.178 5.182 5.183 5.180 0.008 0.813 1.721 0.007 0.525 1.089 0.006 0.260 0.531 0.006 0.209 0.426 #2 Ripple &Noise [mV] 10 20 40 30 40 50 30 50 60 30 50 60 Efficiency [%] Vo [V] Iin [A] 79.6 75.1 82.2 79.2 83.0 81.2 82.7 81.1 5.158 5.152 5.147 5.158 5.152 5.150 5.