Thank you for purchasing our product, an ideal radio system for beginners or experienced users alike. Read this manual carefully before operation in order to ensure your safety, and the safety of others or the safe operation of your system. If you encounter any problem during use, refer to this manual first. If the problem persists, contact your local dealer or visit our service and support website for help: www.Hobbyking.
Table of contents 1. Safety .....................................................................................................................................................3 1.1 Safety Symbols ......................................................................................................................................................3 1.2 Safety Guide..................................................................................................................................................
1. Safety 1.1 Safety Symbols Pay close attention to the following symbols and their meanings. Failure to follow these warnings could cause damage, injury or death. Danger · Not following these instructions may lead to serious injuries or death. Warning · Not following these instructions may lead to major injuries. Attention · Not following these instructions may lead to minor injuries. 1.
2. Introduction The Evolution transmitter and TGY-iA6C receiver constitutes a 2.4GHz AFHDS 2A digital proportional computerized R/C system. This system supports quadcopters. 2.1 System Features The AFHDS 2A (Automatic Frequency Hopping Digital System Second Generation) is specially developed for all radio control models.
2.
2.2.1 Transmitter Antenna Precautions: • • For best signal quality, make sure that the antenna is at about a 90 degree angle to the model. Do not point the antenna directly at the receiver. Never grip the transmitter antenna during operation. It significantly degrades the RF signal quality and strength and may cause loss of control. 2.3 Receiver Overview Status Indicator Update Indicator PPM S.BUS/iBUS VCC Ground Antenna Alt Power Input （0 -- 20V） 2.3.
2.4 USB Simulator Mode The system may be used as a HID controller when connected to a computer via USB. When connected to a computer the function is activated automatically and will be recognized by windows as a game controller. To calibrate or test the system in windows: • • • 1. Type "RUN" into the search bar and select the program. 2. Type "joy.exe" into the "Open:" box and press enter. 3. Select the system and open properties within the game controller menu.
4. Operation Instructions After setting up, follow the instructions below to operate the system. 4.1 Power On Follow the steps below to turn on the system: 1. 2. 3. Check the system and make sure that: • The batteries are fully charged. (Charge the system via USB cable) • The receiver is off and correctly installed. Hold the power buttons until screen lights up. Connect the receiver power supply to the VCC and GND port on the receiver. The system is now powerd on.
5. Home Screen The home screen diplays useful information about your model, including timers and TX/RX status. Start Page TX/RX Battery Status + Battery Setup Menu Timers + Timer Menu Main Menu Display Servos Press and hold the screen to preform a servo test. Note: Make sure that the the engines are turned off/disconected during this test. Failure to do so could lead to harm to yourself or others. The system's navigation is designed to be easy and quick.
6. Function Settings 6.1 Reverse The reverse function changes a channels direction of movement in relation to its input. For example, if the blades are spinning in the wrong direction, pushing the model into the ground instead of taking off, this function can be used to correct this. Setup: To change between normal and reverse touch the box to the right side of the desired channel. Nor = Normal, Rev = Reverse. Select the icon to save and return to the previous menu. 6.
6.4 Subtrim Subtrim changes the center point of the channel. For example, if a model is always drifting to one side, the sub trim can be used to fix this. To set the subtrim function: To change the subtrim: 1. Touch the box to the right of the desired channel. 2. Select the correct decimal and use the up and down arrow keys. 3. Press the 4. Select the or to confirm or cancel changes. icon to save and return to the previous menu. 6.
6.7 LED Setup This function controls the LED's located inside the gimbal. When Idle color mode is off, the system will change colour depending on vertical stick position. When Idle color mode is active the system will maintain a single colour, touch the RGB sliders to change the color. Then select the icon to save and return to the previous menu, select 'Y' when prompted. 6.8 Output Mode The system has four output modes, PWM 、 PPM、i-BUS and S-BUS compatible.
6.10 Select Model The system stores up to 5 different model presets which can be recalled, quickly and easily. To select a model: 1. Touch the model number displayed in a black box. 2. The system will now display the ID menu, use the on-screen up and down arrow keys to navigate to the desired model. 3. Press the to confirm or to cancel. 6.11 Model Reset To reset the current model select model reset from the settings menu and select “Y” for yes. To cancel press “N”. 6.
7. Product Specification 7.1 Transmitter Specification (Evolution) Channels 8 Model type Quadcopter RF range 2.408 ～ 2.475 GHz Bandwidth 500 KHz RF channel 135 RF power Less than 20 dBm 2.4GHz system AFHDS 2A Modulation type GFSK Stick resolution 4096 Low voltage alarm Yes (lower than 3.7V) USB Port Yes Power input 3.7V Antenna length 26 mm*2 Size (Length x Width x Height) 179mm x 81mm x 161mm Color White/Black Certificate CE0678, FCC ID：N4ZMT600，RCM 7.
8.
9. Appendix 1 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of theFCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
FCC ID: N4ZMT600
