Quick Start Guide

24 TCS Passive Series Quick Start Guide 25
Model
Modell
Tabellen nedan sammanfattar de riggdelar eller kit som krävs för olika applikationer, och några exempel på
möjliga riggalternativ illustreras.
Skåp i TCS-serien är utformade med era interna riggpunkter för att passa många möjliga
monteringsmetoder i permanenta installationer. Alla skåp kan enkelt hängas upp med valfria M8- eller
M10-axelöglor kopplade till de medföljande inre riggpunkterna. Ta bort lämpliga försänkta skruvar och byt
ut dem mot ögonbultar som måste ha en gänglängd på minst 18 mm. Använd den bakre riggpunkten för att
vinkla skåpet för optimal täckning av rummet. Skåp kan hängas upp och ner vid behov. Turbosound WB-20,
WB-55 och CB-55 vägg- och takfästen nns som tillval för TCS-serie skåp, och dessa är också kompatibla med
OmniMount * vägg- och takfästen som använder 60 mm x 60 mm hålavstånd.
Vägg Tak Nedfyllning Array Kit Ögonbultar
TCS62
WB-20
TCS62-SB
CB-55
TCS62-SB
TCS62-SB M8 tråd
TCS122 WB-55 CB-55
TCS122-FP
TCS-FK1
TCS-FK2
EB-10-40
TCS152 WB-55 CB-55
TCS152-FP
TCS-FK1
TCS-FK2
EB-10-40
TCS115B
TCS115-FP
TCS-FK3
EB-10-40
TCS Subwoofers EB-10-40
Poniższa tabela zawiera zestawienie części lub zestawów olinowania wymaganych do różnych zastosowań
oraz zilustrowano kilka przykładów możliwych opcji olinowania.
Szafy serii TCS są zaprojektowane z wieloma wewnętrznymi punktami podwieszania, aby dopasować się
do wielu możliwych metod montażu w stałych instalacjach. Wszystkie szafy można po prostu zawiesić za
pomocą opcjonalnych śrub oczkowych M8 lub M10 połączonych z dostarczonymi wewnętrznymi punktami
podwieszania. Wykręć odpowiednie śruby z łbem stożkowym i zastąp je śrubami oczkowymi, które muszą
mieć gwint o długości co najmniej 18 mm. Użyj tylnego punktu podwieszania, aby ustawić szafkę pod kątem,
aby zapewnić optymalne pokrycie pomieszczenia. W razie potrzeby szafki można zawiesić do góry nogami.
Uchwyty ścienne i sutowe Turbosound WB-20, WB-55 i CB-55 są opcjonalnie dostępne dla szaf z serii TCS
i są również kompatybilne z uchwytami ściennymi i sutowymi OmniMount *, które wykorzystują rozstaw
otworów 60 mm x 60 mm.
Ściana Sut Wypełnij Zestaw macierzy Śruby oczkowe
TCS62
WB-20
TCS62-SB
CB-55
TCS62-SB
TCS62-SB Gwint M8
TCS122 WB-55 CB-55
TCS122-FP
TCS-FK1
TCS-FK2
EB-10-40
TCS152 WB-55 CB-55
TCS152-FP
TCS-FK1
TCS-FK2
EB-10-40
TCS115B
TCS115-FP
TCS-FK3
EB-10-40
TCS Subwoofers EB-10-40
(SE) Montering och
xering
(EN) TCS Series Flying
Components
(PL) Montaż i
mocowanie
Wall and Ceiling Brackets
To install a loudspeaker using Turbosound wall and ceiling brackets, rst separate the brackets into their
wall/ceiling plate and speaker plate component parts. Remove the countersunk bolts on the rear panel of the
cabinet. Attach the speaker plate to the cabinet with the bolts supplied. Fix the wall/ceiling plate in the venue
using appropriate xings (not supplied). Lift the loudspeaker on to the wall plate and re-assemble the bracket
parts, adjust the vertical angle and tighten all bolts.
Downll Applications
The TCS62 can be mounted underneath a TCS122 or TCS152 cabinet to provide downll coverage using
the TCS62-SB swivel bracket. First disassemble the swivel bracket into its component parts. Remove the
countersunk bolts from the bottom panel of
the TCS152 cabinet and t the section with
theelongated holes using the xings supplied.
Remove the countersunk bolts on the top panel
and t the swivel bracket using the supplied
xings. Re-assemble the swivel bracket, angle as
appropriate and tighten all xings.
To install the TCS62 in a ceiling-mount
application, separate the component parts as
above, and x the top section to the ceiling
with appropriate xings (not supplied). Fit the
other half to the TCS62 cabinet, re-assemble
the bracket, angle as appropriate and tighten
allxings.
Loudspeaker Arrays and Clusters
An array of two or more cabinets requires the use of kits of yplates and inter-cabinet couplers, which are
xed to the cabinet sides through the M10 rigging points and assembled together in a ‘daisy chain’ fashion to
build up the required array. For all loudspeaker arrays consisting of two or more cabinets:
The number of inter cabinet coupler kits required = the number of boxes – 1, The number of
yplate kits required = the number of boxes.
TCS62-SB
SWIVEL BRACKET
TCS Passive Series