Quick Start Guide

14 TCS-AN SERIES Quick Start Guide 15
TCS-AN DSP Menu Structure
Fullrange Subwoofer Function
PROCESS EQ
None None Sets the frequency response to the default setting.
Array2 –
Sets a corrected frequency response for 2 cabinets
arrayed together.
Array3 –
Sets a corrected frequency response for 3 or more
cabinets arrayedtogether.
User User
Lets you dene your own frequency response setting
by entering the corresponding sub-menu.
Sub menu
Low/ High Shelving Low/ High Shelving Lets you dene a low and high shelving lter.
Parametric 1 & 2 Parametric 1 & 2
Lets you dene a parametric bell-type EQ (Frequency,
Qual. and Gain).
XOVER
None – Unit is set for default full-range reproduction.
HP 100 Hz LP 100 Hz
Preset with 100 Hz, 24 dB/octave lter for crossover
between subwoofer and full-range speakers.
HP 120 Hz LP 120 Hz
Preset with 120 Hz, 24 dB/octave lter for crossover
between subwoofer and full-range speakers.
User User
User crossover sub menu for combination with other
full-range or subwoofer speaker systems
Sub Menu
Freq Freq
Select the desired crossover frequency:
• Fullrange Systems: 75 Hz to 400 Hz.
• Subwoofer Systems: 50 Hz to 150Hz.
Phase Phase Adjust the absolute phase (0° or 180°).
FBQ
Auto Auto
Automatically sets as many lters as required.
Whenever a new feedback frequency is discovered,
the rst lter will be released to attenuate the new
frequency, and so forth.
Single Single
Activates the FBQ (feedback detection) functionality,
up to 8 feedback lters.
Learn Learn
Automatic procedure which searches for feedback
frequencies and locks settings after all 8 lters have
been set.
WARNING!
Please use ear protection during this procedure. The
feedback signal may approach the system's maximum
level, which may cause hearing damage!
Reset Reset Resets all lters.
SETUP
(page 1)
INPUT
Input Input
Lets you choose the audio input source. Choose
between Local (analogue Input) or ULTRANET
(e.g.,P16 monitoring system or M32 audio via
ULTRANET).
Volume Volume
Adjusts the input gain. WithULTRANET digital inputs
over a range from + 10 dB to - 30 dB. With analogue
input from 0 dB to - ∞ dB.
Sensitivity Sensitivity
Adjusts input sensitivity for maxium output when
using an analogue source +4 dBu for normal
opperation, +14dBu for high level input.
Fullrange Subwoofer Function
POSITION
Free –
For positioning the speaker in free suspension or
ground stacked away from walls.
Wall Floor
For positioning the speaker on or next to a wall, or on
the oor (subwoofer)
Ceiling Wall
For positioning the speaker near the ceiling and wall,
or oor and wall (subwoofer)
Corner Corner
For positioning the speaker in a corner next to the
ceiling (xed install) or in a corner on the oor
(subwoofer)
Screenshot update
DELAY
Delay Delay
Adjusts the amount of delay (max300msec = 103 m
or 338 feet).
Unit Unit Selects between msec, metersandfeet.
LIMITER
Limit Limit
Adjust the limiter threshold for the input signal (from
OFF up to -30 dB). This threshold adjustment allows
you to set a max output power which is below the
loudspeaker system’s rated maxoutput.
SETUP
(page 2)
Version Version Displays the installed rmwareversion.
LOAD
1. - 20. 1. - 20.
To load a specic preset, turn the encoder to select
the desired preset's number, and then press either
the ENTER button or the encoder. Whenasked to
conrm press the encoder again or EXIT to abort.
SAVE
1. - 20. 1. - 20.
To save a preset choose the respective preset slot and
press ENTER or theencoder.
Sub Menu
Save Preset Save Preset
Name the preset by choosing the characters with
the encoder and pressing to conrm each character.
When nished, press the ENTER button to save the
preset.
SETUP
Contrast Contrast
Adjust LCD panel contrast. The default contrast value
is 15.
Screen Screen
ON: LCD screen saver (default) turns on automatically
after approx.2minutes.
OFF : LCD turns o automatically after approx. 5
minutes.
Sub Menu
Lock Lock
Lock the device and create a password by choosing
the password characters with the encoder and
pressing to conrm each character. When nished
press the ENTER button. Unlock the device by
entering the password or connecting the unit via USB
to a PCrunning proprietary remote software. The
software does not require apassword.
Warning Warning
In case of overheating, an alert appears on the LCD
screen, and the amplier will shut down until the
unit cools