Quick Start Guide

12
TCS-AN series Quick Start Guide
13
TCS-AN DSP Menu Structure
Fullrange Subwoofer Function
PROCESS
EQ
None None
Sets the frequency response to the
default setting.
Array2 -
Sets a corrected frequency response
for 2 cabinets arrayed together.
Array3 -
Sets a corrected frequency
response for 3 or more cabinets
arrayed together.
User User
Lets you defi ne your own frequency
response setting by entering the
corresponding sub-menu.
Sub menu
Low/ High Shelving Low/ High Shelving
Lets you defi ne a low and high
shelving fi lter.
Parametric 1 & 2 Parametric 1 & 2
Lets you defi ne a parametric bell-type
EQ (Frequency, Qual. and Gain).
XOVER
None -
Unit is set for default full-range
reproduction.
HP 100 Hz LP 100 Hz
Preset with 100 Hz, 24 dB/octave fi lter
for crossover between subwoofer and
full-range speakers.
HP 120 Hz LP 120 Hz
Preset with 120 Hz, 24 dB/octave fi lter
for crossover between subwoofer and
full-range speakers.
User User
User crossover sub menu for
combination with other full-range or
subwoofer speaker systems
Sub Menu
Freq Freq
Select the desired crossover frequency:
• Fullrange Systems: 75 Hz to 400 Hz.
• Subwoofer Systems: 50 Hz to 150 Hz.
Phase Phase
Adjust the absolute phase (0° or 180°).
FBQ
Auto Auto
Automatically sets as many fi lters as
required. Whenever a new feedback
frequency is discovered, the fi rst fi lter
will be released to attenuate the new
frequency, and so forth.
Single Single
Activates the FBQ (feedback detection)
functionality, up to 8 feedback fi lters.
Learn Learn
Automatic procedure which searches
for feedback frequencies and locks
settings after all 8 fi lters have been set.
WARNING!
Please use ear protection during this
procedure. The feedback signal may
approach the system's maximum level,
which may cause hearing damage!
Reset Reset
Resets all fi lters.
SETUP
(page 1)
INPUT
Input Input
Lets you choose the audio input
source. Choose between Local
(analogue Input) or ULTRANET
(e.g., P16 monitoring system or M32
audio via ULTRANET).
Fullrange Subwoofer Function
Volume Volume
Adjusts the input gain.
With ULTRANET digital inputs over
a range from + 10 dB to - 30 dB. With
analogue input from 0 dB to - ∞ dB.
Sensitivity
Sensitivity
Adjusts input sensitivity for maxium
output when using an analogue
source +4 dBu for normal opperation,
+ 14 dBu for high level input.
POSITION
Free -
For positioning the speaker in free
suspension or ground stacked away
from walls.
Wall Floor
For positioning the speaker on or next
to a wall, or on the fl oor (subwoofer)
Ceiling Wall
For positioning the speaker near the
ceiling and wall, or fl oor and wall
(subwoofer)
Corner Corner
For positioning the speaker in a corner
next to the ceiling (fi xed install) or in a
corner on the fl oor (subwoofer)
Screenshot update
DELAY
Delay Delay
Adjusts the amount of delay
(max 300 msec = 103 m or 338 feet).
Unit Unit
Selects between msec,
meters and feet.
LIMITER
Limit Limit
Adjust the limiter threshold for the
input signal (from OFF up to -30 dB).
This threshold adjustment allows you
to set a max output power which is
below the loudspeaker system’s rated
max output.
SETUP
(page 2)
Version Version
Displays the installed fi rmware version.
LOAD
1. - 20. 1. - 20.
To load a specifi c preset, turn the
encoder to select the desired preset's
number, and then press either
the ENTER button or the encoder.
When asked to confi rm press the
encoder again or EXIT to abort.
SAVE
1. - 20. 1. - 20.
To save a preset choose the respective
preset slot and press ENTER or
the encoder.
Sub Menu
Save Preset Save Preset
Name the preset by choosing the
characters with the encoder and
pressing to confi rm each character.
When fi nished, press the ENTER
button to save the preset.
SETUP
Contrast Contrast
Adjust LCD panel contrast. The default
contrast value is 15.
Screen Screen
ON: LCD screen saver (default)
turns on automatically after
approx. 2 minutes.
OFF : LCD turns off automatically after
approx. 5 minutes.