Quick Start Guide

18 NuQ-AN Series Quick Start Guide 19
NuQ-AN DSP Menu Structure
Fullrange Subwoofer Function
PROCESS EQ
None None Sets the frequency response to the default setting.
Live Live Sets the frequency response to a typical live sound setting.
Speech Speech Sets the frequency response for optimal speech intelligibility.
Playback Playback Sets the frequency response ideal for music playback.
User User
Lets you dene your own frequency response setting by
entering the corresponding sub menu.
Sub menu
Low/ High Shelving Low/ High Shelving Lets you dene a low and high shelving lter.
Parametric 1 & 2 Parametric 1 & 2
Lets you dene a parametric bell-type EQ (Frequency, Qual.
and Gain).
XOVER
None - Unit is set for default full rangereproduction.
HP 120 Hz LP 120 Hz
Preset with 120 Hz 24 dB / octave lter for crossover
between subwoofer and full-range speakers.
HP 100 Hz LP 100 Hz
Preset with 100 Hz 24 dB / octave lter for crossover
between subwoofer and full-range speakers.
- NuQ82
Preset with ideal settings for use in combination with NuQ82
fullrangespeaker.
- NuQ102
Preset with ideal settings for use in combination with
NuQ102 fullrangespeaker.
- NuQ122
Preset with ideal settings for use in combination with
NuQ122 fullrangespeaker.
- NuQ152
Preset with ideal settings for use in combination with
NuQ152 fullrangespeaker.
NuQ115B - Preset with high pass alignment for NuQ115B subwoofer.
NuQ118B - Preset with high pass alignment for NuQ118B subwoofer.
User User
User crossover sub menu for combination with other
fullrange or subwoofer speaker systems
Sub Menu
Freq Freq
Select the desired crossoverfrequency:
For fullrange systems: 75 Hz to 400 Hz
For subwoofer systems: 50 Hz to 150Hz
Phase Phase Adjust the absolute phase (0° or 180°)
FBQ
Auto Auto
Automatically sets as many lters as required. Whenever a
new feedback frequency is discovered, the rst lter will be
released to attenuate the new frequency, and so forth.
Single Single
Activates the FBQ (feedback detection) functionality, up to
8 feedback lters
Fullrange Subwoofer Function
Learn Learn
Automatic procedure which searches for feedback
frequencies and locks settings after all 8 lters have
beenset.
WARNING!
Please use ear protection during this procedure. The
feedback signal may approach the system’s maximum
level, which may cause hearingdamage!
Reset Reset Resets all lters.
SETUP
(page 1)
INPUT
Input Input
Lets you choose the audio input source. Choose between
Local (analogue Input) or ULTRANET (e.g.,P16 monitoring
system or M32audio via ULTRANET).
Volume Volume
Adjusts the input gain. With ULTRANET digital inputs over
a range from+ 10 dB to - 30 dB. With analogue input from
0 dB to -∞dB.
Sensitivity Sensitivity
Adjusts input sensitivity for maxium output when using an
analogue source +4 dBu for normal opperation, + 14 dBu
for high level input.
POSITION
Stand Floor
For positioning the speaker on a pole mount stand
(fullrange) or on the oor(Subwoofer)
Wall Wall
For positioning the speaker on or next to a wall (xed
install); alternatively as a monitor speaker (wedge).
Ceiling -
For positioning the speaker on a wall next to the ceiling
(xed install)
Corner Corner
For positioning the speaker in a corner next to the
ceiling (xed install); Forpositioning the speaker in a
corner(subwoofer)
Screenshot update
DELAY
Delay Delay
Adjusts the amount of delay (max300msec = 103.08 m or
338.19feet).
Unit Unit Selector between msec, meterandfeet.
LIMITER
Limit Limit
Adjust the limiter threshold for the input signal (from OFF
down to -30dB). This threshold adjustment allows you to
set a max output power which is below the loudspeaker
system’s rated max output.
SETUP
(page 2)
Version Version Displays the installed rmwareversion.
LOAD
1. - 20. 1. - 20.
To load a specic preset, turn the encoder to select the
desired peset’s number, and then either the ENTER button or
the encoder. When asked to conrm press the encoder again
or EXIT to abort.
SAVE
1. - 20. 1. - 20.
To save a preset choose the respectivepreset slot and press
ENTER or theencoder.