User Guide

66 iQ Series Quick Start Guide 67
Fullrange Subwoofer Function
FBQ
Auto Auto
Automatically sets as many lters as required.
Whenever a new feedback frequency is
discovered, the rst lter will be released to
attenuate the new frequency, and so forth.
Single Single
Activates the FBQ (feedback detection)
functionality, up to 8 feedback lters.
Learn Learn
Automatic procedure which searches for
feedback frequencies and locks settings after all
8 lters have been set.
WARNING!
Please use ear protection during this
procedure. The feedback signal may
approach the system’s maximum level,
which may cause hearing damage!
Reset Reset Resets all lters.
SETUP
(page 1)
INPUT
Input Input
Lets you choose the audio input source.
Choose between 'Analogue', 'Ultranet' (e.g., P16
monitoring system or M32 audio via ULTRANET)
and 'Auto' (automatically switches to Analogue,
when no ULTRANET is connected).
The page also shows the hardware (e.g., HW: A
or B) and the rmware version (e.g., FW: V2.2).
Channel Channel Select the ULTRANET P16 digital input channel.
Trim Trim
Adjusts the input gain of the ULTRANET digital
inputs in a range
fm +10 dB to - 30 dB
Remote Remote
Enables ULTRANET remote control functionality
in order to protect against misuse.
VU VU
Displays the respective input level of all 16
channels receiving via ULTRANET; only visible
when ULTRANET input is selected.
POSITION
Stand Floor
For positioning the speaker on a pole mount
stand (fullrange) or on the oor (subwoofer).
Wall Wall
For positioning the speaker on or next to a
wall (xed install); alternatively as a monitor
speaker (wedge).
Ceiling —
For positioning the speaker on a wall next to the
ceiling (xed install).
Corner Corner
For positioning the speaker in a corner next to
the ceiling (xed install); For positioning the
speaker in a corner (subwoofer).
DELAY
Delay Delay
Adjusts the amount of delay (max 300msec =
103.08m or 338.19 feet).
Unit Unit Selects between msec, meter and feet.
SETUP (page 2)
LIMITER
Limit Limit
Adjust the limiter threshold for the input
signal (from OFF up to -30 dB). This threshold
adjustment allows you to set a max output power
which is below the iQ system’s rated max output.
iQ DSP Menu Structure
Fullrange Subwoofer Function
PROCESS MODEL
Model "xyz" Model "xyz"
Choose from dierent sound Models, either the
Turbosound signature voicing or a DSP model of
an industry standard product.
(alt., MODEL active)
EQ
None None
Sets the frequency response to the default
setting.
Live Live
Sets the frequency response to a typical live
sound setting.
Speech Speech
Sets the frequency response for optimal speech
intelligibility.
Playback Playback
Sets the frequency response ideal for Music
playback.
User User
Lets you dene your own frequency response
setting by entering the corresponding sub menu.
Sub menu
Low/ High Shelving Low/ High Shelving Lets you dene a low and high shelving lter.
Parametric 1 & 2 Parametric 1 & 2
Lets you dene a parametric bell-type EQ
(Frequency, Qual and Gain).
XOVER
None None
Unit is set for default full range/ subwoofer
reproduction.
— iQ8
Preset with ideal settings for use in combination
with iQ8 fullrange speaker.
— iQ10
Preset with ideal settings for use in combination
with iQ10 fullrange speaker.
— iQ12
Preset with ideal settings for use in combination
with iQ12 fullrange speaker.
— iQ15
Preset with ideal settings for use in combination
with iQ15 fullrange speaker.
iQ15B —
Preset with high pass alignment for iQ15B
subwoofer.
iQ18B —
Preset with high pass alignment for iQ18B
subwoofer.
User User
User crossover sub menu for combination with
other fullrange or subwoofer speaker systems.
Sub Menu
Freq Freq
Select the desired crossover frequency:
For Fullrange Systems: 75 Hz to 400 Hz
For Subwoofer Systems: 50 Hz to 150 Hz
Phase Phase Adjust the absolute phase (0° or 180°)