User's Guide

Ｍagnetic suction automatic postioning
wireless charging mobile phone holder
This product is compatible with iPhone 12/ 13 series
Please read this operation
Instruction carefully and keep it properly before using this product
Product introduction
Thank you for purchasing and using this products! In order to
ensure that you can provide a better operating experience for your
mobile phone or electronic products.
USER GUIDE
1. Please align the phone magnet with the wireless charging
magnet to avoid the magnetic attraction does not work.
2. Please make sure you are using Magsafe cases. It can’t compatible
with non-MagSafe cases. Non-MagSafe cases will make magnetic
force is weak and can’t charge.
3. No metal plate on the back of phone, because it will stop phone
charging
.
4.
Don’t use the wireless charger in high temperature, humidity or
corrosive environment, avoid damaging the circuit and avoid leadage.
5. Take care of children to ensure they will not play with wireless charger
as a toy, in order to avoid uncessary accidents.
6. To ensure the fast and safe charging, we select the QC2.0/QC3.0
standard car charger and the best four-core universal data cable, others
nonstandard car charger or cables will make the charging slow.
7. If the car temperature inside is too high, the charging wil
become slow; with the cold wind from the air outlet, charging
on the air outlet will be much better, with the hot wind from the
air outlet, please charging the mount on the dashboard.
Note!
7. Install the bracket to the vent, tighten the bracket by
roating the nut, and then connect the car charger and
mini USB cable that meet QC3.0 standard for power supply
6. Loose the nut and open
the air outlet chuck
1. Please wipe the car dashboard
carefully with the damp cloth
Operation
Applicable model
Frequency
Input power
Efficiency
Output power
Compliance with Qi standard smart phone
5V 5W | 9V 7.5W
5V 2A | 9V 1.67A | 12V 2A
PS：These above information is based on real sample testing, it wil be a little bit differenbt
for variour products in different conditions.
5. Other bracket base can
be replaced
3. Paste the bracket on the
daskboard
2.
Tear off the protection
film of the tape
Product name Model name Z10W06Qi Car Charger
Operating
temperature
0℃~45℃
CCAO21LP1850T7
NCC Warning：
For low-power radio frequency equipment that has been certified, companies, firms, or users are not allowed to change the frequency,
increase the power, or change the characteristics and functions of the original design without approval.
The use of low-power radio frequency equipment must not affect flight safety and interfere with legal communications;
if interference is found, it should be stopped immediately and improved to no interference before continuing to use.
Legal communications in the preceding paragraph refers to radio communications that operate in accordance with the provisions of the
Telecommunications Administration Law. Low-power radio frequency equipment must endure the interference of legal communications
or industrial, scientific and medical radio wave radiation electrical equipment.
Accessory
Suction stand
Cable Air conditioner
Magnet ring
設備名稱：Qi 無線車充組 型號 (型式) : Z10W06
Equipment name Type designation (Type)
Unit
限用物質及其它化學符號
Restricted substances and its chemical symbols
鉛Lead
(Pb)
汞Mercury
(Hg)
鎘Cadmium
(Cd)
六價鉻
Hexavalent
chromium
(Cr+6)
多溴聯苯
Polybrominated
biphenyls
(PBB)
多溴二苯醚
Polybrominated
dipheny1 ethers
(PBDE)
Circuit
board
Metal
board
Silicone
Metal glue
備考1. “超出0.1 wt %”及 “超出0.01 wt%” 係指限用物質之百分比含量超出百分比含量基準值
。
Note 1: “Exceeding 0.1 wt %” and “exceedingt 0.01 wt %”indicate that the percentage
content of the restricted substance exceeds the reference percentage value of pressence condition.
備考2. “O” 係指該項限用物質之百分比含量未超出百分比含量基準值。
Note 1: “O” indicates that the percentage content of the restricted substance does not exceed the percentage
of reference value of presence.
備考3. “—” 係指該項限用物質為除項目。
Note 3: “The “—”. indicates that the restricated substance corresponds to the expemption.
O O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Importer Sagittech Technology
Address
3rd Floor, No. 30, Section 1, Chongqing North Road, Datong District, Taipei City
12V 10W| 12V 15W
R3E226
RoHS
4. Plug in the charging cable
, shake the phone to align
the magnet then complete
the installation
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device
could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
The equipment complies with FCC RF exposure limits set forth for an uncontrolled
environment.
During the operation of device a distance of 15cm surrounding the device and
20cm above the top surface of the device must be respected.