User guide

ManualsBrandsTuffy Security ManualsCar142

Page 1 of 6 - 3/6/2009 – Rev030609

INSTALLATION INSTRUCTIONS

Single Compartment Overhead Console #142

Please read and fill out the enclosed warranty registration card to activate your warranty.

Shipment Contents

#12

Top Panel Slide Assembly #1 Electronics Mounting Bracket #4 Clamp Bracket

#8 Windshield Mounting Bracket #7.9 Wire Clamp #7.20 Wire Loom #9.15 Rubber Seal

#9.13 10-32x3/4 Knob Screw #7.13 (2) ¼-20x1 Screw #7.19 (7) 10-32x1/2 Allen Screw #7.10 (4) 10-32x1/2 Hex Screw

#7.14 (2) ¼-20 Nylock Nut #7.3 (4) 10-32 Nylock Nuts #7.11 (3) 10-32 Flange Nuts (7.15) ¼” Washers

#7.2 (5) #10 Washers #7.1 (2) 1” Grommets

TOOLS / PARTS NEEDED

• T-25 Torx wrench

• 1/8” Allen Wrench or socket

• 5/32” Allen Wrench or socket

• 5/16” Wrench and/or socket

• Ratchet and 3/8” socket, 7/16” socket, & 10mm socket

• Black Electrical tape

• Any electrical wires, connectors, etc. to install electronic equipment. (Read completed instructions prior to making this

list of parts to avoid unnecessary trips to the store)

Summary of content (6 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Single Compartment Overhead Console #142 Please read and fill out the enclosed warranty registration card to activate your warranty. Shipment Contents #12 Top Panel Slide Assembly #8 Windshield Mounting Bracket #9.13 10-32x3/4 Knob Screw #7.14 (2) ¼-20 Nylock Nut #7.2 (5) #10 Washers #7.9 Wire Clamp #7.13 (2) ¼-20x1 Screw #7.3 (4) 10-32 Nylock Nuts #1 Electronics Mounting Bracket #7.20 Wire Loom #7.19 (7) 10-32x1/2 Allen Screw #4 Clamp Bracket #9.15 Rubber Seal #7.
PAGE 2
PLEASE READ ALL INSTRUCTIONS THOROUGHLY BEFORE STARTING INSTALLATION. 1. Install the #7.7 electronics equipment (Not included) in the #1 Electronics mounting bracket using the hardware illustrated #7.19 and #7.1. #7.12 is a stereo support strap that usually comes with the stereo. Plummer’s strap, which can be purchased at any hardware store, can be substituted and is also helpful when mounting CBs or other equipment.
PAGE 3
14. Insert the #8 Windshield mounting bracket over the center loop catch as illustrated then refasten both #7.5 loops with the original hardware #7.16. (See Figure 4) 15. Re-install the #7.21 cover by tucking the ends in then aligning the inserts and pressing firmly to pop it securely in. (See Figure 4) 16. Remove the #7.6 factory sound bar by removing the 6 mounting screws and unplugging the wiring harness. Save all this hardware it will all be reinstalled.
PAGE 4
FIGURE 1 FIGURE 2 Page 4 of 6 - 3/6/2009 – Rev030609
PAGE 5
FIGURE 3 FIGURE 4 Page 5 of 6 - 3/6/2009 – Rev030609
PAGE 6
FIGURE 5 FIGURE 6 Call (970) 564-1762 for Technical Support Page 6 of 6 - 3/6/2009 – Rev030609