User's Manual

B. SERIAL TERMINAL OUTPUT AT START-UP
≡
B Serial terminal output at start-up
Appendix B shows a sample CLI output at start-up in SHOP mode.
 
1 ================================================
2 TTTech TTE -SMC2 Image 2.5.0
3 Jun 10 2020 @ 14:11:50
4 ================================================
5 [INIT STAGE ]
6 Shutdown cause:0 info :13
7 Lifetime: 370:27:36
8 [CONFIGURATION STAGE ]
9 ### Mode changed RESTRICTED : OFF
10 ### State changed INIT -> SHOP
11 Reading Config Pins from Config Plug .
12 Shop Mode
13 Initializing SWE ...
14 SWE : Aero ASIC2 SWE IP (0 x03030000)
15 Initializing ES ...
16 TTE -ES: Device ID: 0 x99000946 , Device Revision :0x0032F001 ES Core
Version:0 x18190000
17 ES: 1.8.24 (0x0032F001)
18 Reading Config Pins from Config Plug .
19 Configured Position: 0
20 Loading default configuration ...
21 Applied config SW0 from position 0 page CONFIGS_DEF
22 ID :0 IP :10.10.10.10 MSK :255.255.255.0 GW:10.10.10.255
23 MAC 02:00:00:00:01:20
24 Setting PHY 1 (88 E1548 ): COPPER -> 1Gbit/s (full duplex ) with AutoNeg MODE ->
AMD SGMII/Copper SFP at Port 1 unplugged.
25 Setting PHY 2 (88 E1548 ): COPPER -> 1Gbit/s (full duplex ) with AutoNeg MODE ->
AMD SGMII/Copper SFP at Port 2 unplugged.
26 Setting PHY 3 (88 E1548 ): COPPER -> 1Gbit/s (full duplex ) with AutoNeg
27 Setting PHY 4 (88 E1548 ): COPPER -> 1Gbit/s (full duplex ) with AutoNeg
28 Setting PHY 5 (88 E1548 ): COPPER -> 1Gbit/s (full duplex ) with AutoNeg
29 Setting PHY 6 (88 E1548 ): COPPER -> 1Gbit/s (full duplex ) with AutoNeg
30 Setting PHY 7 (88 E1548 ): COPPER -> 100Mbit/s (full duplex ) with AutoNeg
31 Setting PHY 8 (88 E1548 ): COPPER -> 100Mbit/s (full duplex ) with AutoNeg
32 Setting PHY 9 (88 E1548 ): COPPER -> 100Mbit/s (full duplex ) with AutoNeg
33 Setting PHY 10 (88 E1548 ): COPPER -> 100 Mbit/s (full duplex ) with AutoNeg
34 Setting PHY 11 (88 E1548 ): COPPER -> 100 Mbit/s (full duplex ) with AutoNeg
35 Setting PHY 12 (88 E1548 ): COPPER -> 100 Mbit/s (full duplex ) with AutoNeg
36 Setting PHY 13 (88 E1548 ): COPPER -> 100 Mbit/s (full duplex ) with AutoNeg
37 Setting PHY 14 (88 E1548 ): COPPER -> 100 Mbit/s (full duplex ) with AutoNeg
38 Setting PHY 15 (88 E1548 ): COPPER -> 100 Mbit/s (full duplex ) with AutoNeg
39 Setting PHY 16 (88 E1548 ): COPPER -> 100 Mbit/s (full duplex ) with AutoNeg
40 Setting PHY 17 (88 E1548 ): COPPER -> 100 Mbit/s (full duplex ) with AutoNeg
41 Setting PHY 18 (88 E1548 ): COPPER -> 100 Mbit/s (full duplex ) with AutoNeg
42 Setting PHY 19 (88 E1548 ): COPPER -> 100 Mbit/s (full duplex ) with AutoNeg
43 Setting PHY 20 (88 E1548 ): COPPER -> 100 Mbit/s (full duplex ) with AutoNeg
44 Setting PHY 21 (88 E1548 ): COPPER -> 100 Mbit/s (full duplex ) with AutoNeg
45 Setting PHY 22 (88 E1548 ): COPPER -> 100 Mbit/s (full duplex ) with AutoNeg
46 Setting PHY 23 (88 E1548 ): COPPER -> 100 Mbit/s (full duplex ) with AutoNeg
47 Setting PHY 24 (88 E1548 ): COPPER -> 100 Mbit/s (full duplex ) with AutoNeg
48 Setting PHY 25 (88 E1548 ): COPPER -> 100 Mbit/s (full duplex ) with AutoNeg
49 Initializing Application Ports ... Initializing BPDU application ports ... done
50 Management functionality via best effort
51 Initializing CAL ... done
52 Initializing Network Stack ... done
© TTTech Computertechnik AG 2020. All rights reserved.
Confidential and Proprietary Information
38
Document Number:
D-A664Lab-G-05-001